Andreas Walter Bett

Andreas Walter Bett

Auto-generated profile, based on publicly available information

Andreas Walter Bett

Fraunhofer Institute for Solar Energy Systems ISE, Heidenhofstr. 2, 79110 Freiburg, Germany

Research Focus & Metrics

Academic Career Length

23Years (2004-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
18 September 2018 in IEEE Journal of Photovoltaics
Verified
Journal Article
Closed access
MFMarkus Feifel
Markus Feifel
JOJens Ohlmann
Jens Ohlmann
JBJan Benick
Jan Benick
MHMartin Hermle
Martin Hermle
JBJurgen Belz
Jurgen Belz
FDFrank Dimroth
Frank Dimroth
Monolithic multi-junction solar cells made on active silicon substrates are a promising pathway for low-cost high-efficiency devices. We present results of GaInP/GaAs/Si triple-junction solar cells, fabricated by direct growth on silicon in a metal–organic vapor phase epitaxy reactor using a GaAs $_{y}$ P $_{1-}$ $_{y}$ buffer structure to overcome the lattice mismatch between Si and GaAs. A low-temperature (750 °C) Si surface preparation process and a SiN $_{x}$ diffusion barrier at the rear side have been implemented to maintain the minority carrier lifetime in the Si bottom cell. Conversion efficiencies up to 19.7% have been achieved under AM 1.5g spectral conditions. The cells are compared with identical GaInP/GaAs dual-junction solar cells grown on bulk GaP and GaAs substrates to identify loss mechanisms. Subcell electrical characterization using electroluminescence reveals a significant voltage loss of the III–V subcells on Si, compared with the same structures grown on GaP or GaAs. Electron channeling contrast imaging of the metamorphic GaAs $_{y}$ P $_{1-}$ $_{y}$ buffer shows a three times higher threading dislocation density on Si (1.4 × 108 cm−2) than on GaP substrates, and atomic force microscopy shows holes in the GaAs $_{y}$ P $_{1-}$ $_{y}$ buffer on Si that are not observed on GaP. Approaches to reach lower defect densities for the III–V layers on silicon are discussed.

1 January 2015 in Journal of Photonics for Energy
Verified
Journal Article
Closed access
PDF file
AWAlexandre W. Walker
Alexandre W. Walker
OHOliver Höhn
Oliver Höhn
DMDaniel N. Micha
Daniel N. Micha
LWLukas Wagner
Lukas Wagner
HHHenning Helmers
Henning Helmers
FDFrank Dimroth
Frank Dimroth
Modeling single junction solar cells composed of III–V semiconductors such as GaAs with the effects of photon recycling yields insight into design and material criteria required for high efficiencies. For a thin-film single junction GaAs cell to reach 28.5% efficiency, simulation results using a recently developed model which accounts for photon recycling indicate that Shockley–Read–Hall (SRH) lifetimes of electrons and holes must be longer than 3 and 1 μs, respectively, in a 2-μm thin active region, and that the native substrate must be removed such that the cell is coupled to a highly reflective rear-side mirror. The model is generalized to account for luminescence coupling in tandem devices, which yields direct insight into the top cell’s nonradiative lifetimes. A heavily current mismatched GaAs/GaAs tandem device is simulated and measured experimentally as a function of concentration between 3 and 100 suns. The luminescence coupling increases from 14% to 33% experimentally, whereas the model requires increasing electron and hole SRH lifetimes to explain these results. This could be an indication of the saturating defects which mediate the SRH process. However, intermediate GaAs layers between the two subcells may also contribute to the luminescence coupling as a function of concentration.

1 January 2006
Verified
Conference Paper
Closed access
ABA. W. Bett
A. W. Bett
BBB. Burger
B. Burger
FDF. Dimroth
F. Dimroth
GSG. Siefer
G. Siefer
HLH. Lerchenmuller
H. Lerchenmuller
Recently, high-concentration PV using III-V solar cells becomes more attractive and several companies were founded. In the first part of this paper we present examples of III-V based high-concentration systems. The second part of the paper is devoted to experimental results obtained for a CPV system using FLATCONreg-type modules. An averaged system efficiency of 19.1% and a maximum system efficiency of 22.2% were determined. FLATCONreg test modules using triple-junction solar cells achieved outdoor measured efficiencies of 26.8%

23 October 2006 in Journal of Solar Energy Engineering
Verified
Journal Article
Closed access
PDF file
KVK. Volz
K. Volz
TTT. Torunski
T. Torunski
DLD. Lackner
D. Lackner
OROleg Rubel
Oleg Rubel
WSW. Stolz
W. Stolz
ABA. W. Bett
A. W. Bett
The dilute nitride (GaIn)(NAs) material system grown lattice matched to GaAs or Ge with a 1eV band gap is an interesting material for the use in four-junction solar cells with increased efficiencies. As a result of its metastability, several challenges exist for this material system, which up to now limits the device performance. We performed nanostructural analysis in combination with photoluminescence characterization to optimize the metal organic vapor phase growth as well as the annealing conditions for the quaternary solar cell material. The optimum annealing conditions depend strongly on the In content of the quaternary material. Valence force field calculations of stable N environments in the alloy support the model that the N moves from a Ga rich environment realized during growth into an In rich environment upon annealing. Simultaneously, N induced strain fluctuations, which are detected in the N containing material upon growth, are dissolved and the device properties are improved.

14 October 2010 in IEEE Transactions on Electron Devices
Verified
Journal Article
Closed access
HHHenning Helmers
Henning Helmers
EOEduard Oliva
Eduard Oliva
WBWolfgang Bronner
Wolfgang Bronner
FDFrank Dimroth
Frank Dimroth
ABAndreas W. Bett
Andreas W. Bett
Monolithic interconnected modules are large-area high-voltage photovoltaic devices that are realized through solar cell segments that are series-connected via interconnection trenches during wafer processing. This paper investigates different processing techniques, giving detailed information about each processing sequence. In the first approach, a wet chemical etching procedure and photo-defined polyimide as dielectric film is used, leading to minimal trench width of 86 μm. Furthermore, we examine the applicability of advanced processing techniques. An alternative dry-etching process using reactive ion etching in inductively coupled plasma is investigated. With this technique, smooth and near-vertical sidewalls could be achieved, whereas the undercuts in etching profile, which are inevitable when using wet chemical etching, could be avoided. Moreover, an accurate processing technique for plasma-enhanced chemical vapor deposited SiN x as a dielectric film for electrical isolation is presented. This allowed sufficient isolation to be achieved, as well as enabling precise structuring. With these advanced processing techniques, trench widths of 57 μm were realized, resulting in a reduction of area losses due to interconnection from 9% to below 6%.

4 January 2012
Verified
Book Chapter
Closed access
PDF file
SPSimon P. Philipps
Simon P. Philipps
WGWolfgang Guter
Wolfgang Guter
EWElke Welser
Elke Welser
JSJan Schöne
Jan Schöne
MSMarc Steiner
Marc Steiner
ABAndreas W. Bett
Andreas W. Bett