We present an extensive study leading to a general understanding about the optical transitions involved in the surface photovoltage (SPV) spectra of type-I quantum well (QW) structures. SPV measurements were carried out on QW samples with varying QW width and on QW samples with varying aluminum content. The results are compared with experimental electroreflectance spectra, absorption spectra simulated with multiband computations, and theoretical calculations of the electronic states in the QWs. Thus, the transitions which induce steps in the SPV spectra are unambiguously identified. Most remarkably, the bound electron-to-free hole transition is detected by SPV measurements. This distinguishes the SPV method from many other optical techniques like photoluminescence and photoreflectance spectroscopy that allow only the observation of bound-to-bound and free-to-free transitions. The analogous free electron-to-bound hole transition does not give rise to a feature in the SPV spectra. In addition, the bound-to-bound transitions , , and are observed, if the respective states are confined. Also, the free-to-free transition is measured. We demonstrate how these transitions can typically be identified in the spectra without any further measurements or calculations. With this knowledge, the practical band offsets of the QW structure, i.e., the energy difference between the lowest confined states in the QW and the extended states in the barrier, can be extracted directly from the spectra. An advantage over conventional techniques for the determination of band offsets is that neither any additional knowledge of other QW parameters nor simulations are necessary. As an example for the application of the SPV technique, the electronic states and band offsets of a series of QWs with varying QW width are characterized. These experiments directly show that nitrogen affects only the conduction band states.
23 October 2006 in Journal of Solar Energy Engineering
The dilute nitride material system grown lattice matched to or Ge with a band gap is an interesting material for the use in four-junction solar cells with increased efficiencies. As a result of its metastability, several challenges exist for this material system, which up to now limits the device performance. We performed nanostructural analysis in combination with photoluminescence characterization to optimize the metal organic vapor phase growth as well as the annealing conditions for the quaternary solar cell material. The optimum annealing conditions depend strongly on the In content of the quaternary material. Valence force field calculations of stable N environments in the alloy support the model that the N moves from a Ga rich environment realized during growth into an In rich environment upon annealing. Simultaneously, N induced strain fluctuations, which are detected in the N containing material upon growth, are dissolved and the device properties are improved.
Self-mode-locking has become an emerging path to the generation of ultrashort pulses with vertical-external-cavity surface-emitting lasers. In our work, a strong Kerr nonlinearity that is so far assumed to give rise to mode-locked operation is evidenced and a strong nonlinearity enhancement by the microcavity is revealed. We present wavelength-dependent measurements of the nonlinear absorption and nonlinear refractive index change in a gain chip using the Z-scan technique. We report negative nonlinear refraction up to 5x10−12 cm2/W in magnitude in the (InGa)As/Ga(AsP) material system close to the laser design wavelength, which can lead to Kerr lensing. We show that by changing the angle of incidence of the probe beam with respect to the gain chip, the Kerr nonlinearity can be wavelength-tuned, shifting with the microcavity resonance. Such findings may ultimately lead to novel concepts with regard to tailored self-mode-locking behavior achievable by peculiar Kerr-lens chip designs for cost-effective, robust and compact fs-pulsed semiconductor lasers.
1 May 1996 in SAE International Journal of Advances and Current Practices in Mobility
Quantitative Laser-Induced Incandescence (LII) has been applied to investigate the soot formation in a combusting Diesel jet for various conditions. For the quantification of the LII signal the local soot volume fraction of a diffusion flame burner was measured using laser beam extinction. These data were used for the calibration of the LII signal. The investigation of the soot formation in a combusting Diesel jet was performed in a high pressure, high temperature combustion chamber with optical access. A wide range of pressure (up to 10 MPa) and temperature (up to 1,500 K) conditions could be covered using a hydrogen precombustion, which is initiated inside the chamber before fuel injection. The influence of different gas atmospheres have been investigated by varying the gas composition (H2, O2 and N2) inside the chamber. Local soot volume fractions (up to 12 × 10-6) of different combusting Diesel sprays were measured time (<100 ns) and 2D-spatially resolved (578 x 384 Pixel, <100 μm per pixel). The measurements indicate, that at the initial stage of combustion a decrease of the oxygen concentration of 25% (compared to air) reduces the maximum local soot volume fraction by a factor of 5 to 6. Additionally at this condition the ignition delay is longer.
We report on the design and fabrication of high-power, high-brightness diode-pumped vertical-external-cavity surface-emitting lasers. Over 3 W continuous wave fundamental transverse mode output at 980 nm with a high slope efficiency of 44% is demonstrated at room temperature. The diffraction-limited beam with factor of 1.15 at high-power operation is achieved. A vertical-external-cavity surface-emitting laser operating near 976 nm with a diffraction-limited beam is used to pump the core of 3 cm long -codoped single-mode phosphate fiber lasers. An output power in excess of 250 mW at 1535 nm with a slope efficiency of 29% is obtained without any cooling.