14 February 2019 in Advanced Materials
The latest progress and future perspectives of thin film photovoltaic kesterite technology are reviewed herein. Kesterite is currently the most promising emerging fully inorganic thin film photovoltaic technology based on critical raw‐material‐free and sustainable solutions. The positioning of kesterites in the frame of the emerging inorganic solar cells is first addressed, and the recent history of this family of materials briefly described. A review of the fast progress achieved earlier this decade is presented, toward the relative slowdown in the recent years partly explained by the large open‐circuit voltage (VOC) deficit recurrently observed even in the best solar cell devices in the literature. Then, through a comparison with the close cousin Cu(In,Ga)Se2 technology, doping and alloying strategies are proposed as critical for enhancing the conversion efficiency of kesterite. In the second section herein, intrinsic and extrinsic doping, as well as alloying strategies are reviewed, presenting the most relevant and recent results, and proposing possible pathways for future implementation. In the last section, a review on technological applications of kesterite is presented, going beyond conventional photovoltaic devices, and demonstrating their suitability as potential candidates in advanced tandem concepts, photocatalysis, thermoelectric, gas sensing, etc.
27 October 2017 in Energy & Environmental Science
A fundamental analysis of the impact of Ge on the synthesis of Cu2ZnSnSe4:Ge by a sequential process is presented, reporting the consequences on the absorber morphology and solar cell devices performance.
7 August 2015 in Advanced Energy Materials
6 May 2019 in Journal of Materials Chemistry A
Polycrystalline kesterite Cu2ZnSnSe4 (CZTSe) semiconductors have drawn attention as promising absorber candidates for the next generation of thin film photovoltaics. However, the narrow tolerance to stoichiometry variations, which favours the formation of secondary phases and cluster defects, is a challenging drawback that restrains the device performance. In this context Raman spectroscopy has been demonstrated to be a powerful tool for the characterization of CZTSe, allowing the assessment of relevant parameters such as structure, crystal quality and secondary phases. In this work, multiwavelength Raman scattering measurements using nine excitation wavelengths (from 325 to 1064 nm) were performed on CZTSe polycrystalline thin films in order to give a detailed identification of all the active Raman modes expected in this crystalline structure. The experimental results compare well with the vibrational properties that have been computed by first-principles calculations based on density functional theory. Calculations of the phonon density of states (PDOS), as well as the simulation of the Raman spectra, have allowed a better understanding of the experimentally observed vibrational modes. A “non-band gap resonant” Raman effect was observed under 325 nm excitation conditions, making ultra-violet (UV) Raman spectroscopy a very promising characterization technique due to its high sensitivity to the surface region which provides information on the buffer/absorber interface. Strong intensity enhancement of spectral regions around 176 cm−1 and 250 cm−1 is observed. Calculated PDOS and combinatorial experiments on more than 200 samples with stoichiometries close to the high efficiency device compositions lead to the correlation of these intensities with the concentration of VCu and ZnSn point defects, respectively. Correlation with the optoelectronic properties of the devices allowed identification of the optimal concentration of VCu and ZnSn point defects for the highest performance devices. The application of the presented methodology has been confirmed by performing the same Raman analysis on the CZTSe absorber with 11% device efficiency. This work demonstrates that defect engineering in CZTSe is of the foremost importance for the improvement of solar cell performance, and that UV-based Raman spectroscopy is an effective technique for the non-destructive assessment of defects in kesterite materials.
6 January 2016 in Journal of Materials Chemistry A
MEMoisés Espíndola-Rodríguez
Moisés Espíndola-Rodríguez
+8
Different alkali doping methods to introduce Na and/or K in flexible and light-weight Cu2ZnSnSe4 solar cells were compared. A maximum efficiency of 6.1% was achieved.
1 August 2016 in Nano Energy
Cu2ZnSn(SxSe1-x)4 (CZTSSe) photovoltaic absorbers could be the earth-abundant and low toxicity replacement for the already commercialized CuIn1-xGaxSe2 (CIGS) thin film technology. In order to make this possible, specific research efforts applied to the bulk, front and back interfaces must be performed with the aim of improving CZTSSe performance. In this paper the importance of back contact modification to obtain high efficiency Cu2ZnSnSe4 (CZTSe) solar cells and to increase a paramount and limiting parameter such as VOC is highlighted. Several Mo configurations (monolayer, bi-layer and tri-layer) with different electrical and morphological properties are investigated in CZTSe solar cells. An optimum tri-layer configuration in order to minimize overselenization of the back contact during thermal annealing while keeping reasonable electrical features is defined. Additionally, a thin intermediate MoO2 layer that results in a very effective barrier against selenization and innovative way to efficiently assist in the CZTSe absorber sintering is introduced. The use of this layer enhances grain growth and subsequently the efficiency of solar cells increases via major VOC and FF improvement. An efficiency increase from 7.2% to 9.5% is obtained using a Mo tri-layer with a 20 nm intermediate MoO2 layerThis research was supported by the Framework 7 program under the project KESTCELLS (FP7-PEOPLE-2012-ITN-316488), by MINECO (Ministerio de Economía y Competitividad de España) under the SUNBEAM project (ENE2013-49136-C4-1-R), and by European Regional Development Founds (ERDF, FEDER Programa Competitivitat de Catalunya 2007–2013). Authors from IREC and the University of Barcelona belong to the M-2E (Electronic Materials for Energy) Consolidated Research Group and the XaRMAE Network of Excellence on Materials for Energy of the “Generalitat de Catalunya”. M.E-R. thanks the MINECO for the FPI-MINECO (BES-2011-045774), Y.S. for the PTA fellowship (PTA2012-7852-A), SG for the FPI fellowship (BES-2014-068533), M.P. for the MINECO postdoctoral fellow (FPDI-2013-18968), E.S. and R.C. for the “Ramon y Cajal” fellowship (RYC-2011-09212) and (RYC-2011-08521) respectively, and H.X. thanks the “China Scholarship Council” fellowship (CSC Nº 201206340113