Hiroki Ohno

Hiroki Ohno

Auto-generated profile, based on publicly available information

Hiroki Ohno

Division of Biomaterials and Bioengineering, Department of Oral Rehabilitation, School of Dentistry, Health Sciences University of Hokkaido

Research Focus & Metrics

Academic Career Length

31Years (1996-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 July 2006 in The Angle Orthodontist
Verified
Journal Article
Closed access
MIMasahiro Iijima
Masahiro Iijima
KEKazihiko Endo
Kazihiko Endo
TYToshihiro Yuasa
Toshihiro Yuasa
HOHiroki Ohno
Hiroki Ohno
KHKazuo Hayashi
Kazuo Hayashi
IMItaru Mizoguchi
Itaru Mizoguchi
The purpose of this study was to provide a quantitative assessment of galvanic corrosion behavior of orthodontic archwire alloys coupled to orthodontic bracket alloys in 0.9% NaCl solution and to study the effect of surface area ratios. Two common bracket alloys, stainless steels and titanium, and four common wire alloys, nickel-titanium (NiTi) alloy, beta-titanium (beta-Ti) alloy, stainless steel, and cobalt-chromium-nickel alloy, were used. Three different area ratios, 1:1, 1:2.35, and 1:3.64, were used; two of them assumed that the multibracket appliances consists of 14 brackets and 0.016 inch of round archwire or 0.016 x 0.022 inch of rectangular archwire. The galvanic current was measured for 3 successive days using zero-impedance ammeter. When the NiTi alloy was coupled with Ti (1:1, 1:2.35, and 1:3.64 of the surface area ratio) or beta-Ti alloy was coupled with Ti (1:2.35 and 1:3.64 of the surface area ratio), Ti initially was the anode and corroded. However, the polarity reversed in 1 hour, resulting in corrosion of the NiTi or beta-Ti. The NiTi alloy coupled with SUS 304 or Ti exhibited a relatively large galvanic current density even after 72 hours. It is suggested that coupling SUS 304-NiTi and Ti-NiTi may remarkably accelerate the corrosion of NiTi alloy, which serves as the anode. The different anode-cathode area ratios used in this study had little effect on galvanic corrosion behavior.

1 May 2004 in Dental Materials
Verified
Journal Article
Closed access
HOHiroki Ohno
Hiroki Ohno
KEKazuhiko Endo
Kazuhiko Endo
MHMasanori Hashimoto
Masanori Hashimoto

1 January 1998 in Corrosion Engineering
Verified
Journal Article
Closed access
KEKazihiko Endo
Kazihiko Endo
YAYoshihiro Abiko
Yoshihiro Abiko
MSMasahiro Suzuki
Masahiro Suzuki
HOHiroki Ohno
Hiroki Ohno
TKTohru Kaku
Tohru Kaku

1 January 2000 in Dental Materials Journal
Verified
Journal Article
Open access
KEKazihiko Endo
Kazihiko Endo
MSMasahiro Suzuki
Masahiro Suzuki
HOHiroki Ohno
Hiroki Ohno
The corrosion behaviors of four ferric stainless steels and two austenitic stainless steels were examined in a simulated physiological environment (0.9% NaCl solution) to obtain basic data for evaluating the appropriate composition of stainless steels for dental magnetic attachments. The corrosion resistance was evaluated by electrochemical techniques and the analysis of released metal ions by atomic absorption spectrophotometry. The surface of the stainless steels was analyzed by X-ray photoelectron spectroscopy (XPS). The breakdown potential of ferric stainless steels increased and the total amount of released metal ions decreased linearly with increases in the sum of the Cr and Mo contents. The corrosion rate of the ferric stainless steels increased 2 to 6 times when they were galvanically coupled with noble metal alloys but decreased when coupled with commercially pure Ti. For austenitic stainless steels, the breakdown potential of high N-bearing stainless steel was approximately 500 mV higher than that of SUS316L, which is currently used as a component in dental magnetic attachments. The enriched nitrogen at the alloy/passive film interface may be effective in improving the localized corrosion resistance.

1 January 2001 in Dental Materials Journal
Verified
Journal Article
Open access
HOHiroki Ohno
Hiroki Ohno
KEKazihiko Endo
Kazihiko Endo
YYYuro Yamane
Yuro Yamane
IKIsao Kawashima
Isao Kawashima
Three precious metal alloys, Type IV gold alloy, 14 K gold alloy, and silver-based alloy, were treated with different surface modifications including a metal primer (VBATDT) application, a SiOx coating method, high-temperature oxidation, modification method with a liquid Ga-Sn alloy, and tin electroplating. Then thin PMMA films were bonded with a resin containing 4-META. Water durability at the adhesion interface was evaluated after water immersion, followed by thermal cycling used liquid nitrogen. The weakest zone at the interface was investigated using XPS only for the Ag-Pd alloy specimens that had been surface-treated with as-polishing, adhesive primer, and the SiOx coating method, since peeling of the PMMA film on the surface of specimens surface-treated by other methods was not observed. Metal elements were detected from the resin side at the adhesion interface. The chemical states of Cu in the resin before argon ion etching were characterized as metal oxides and/or states of chemical interaction with 4-META, VBATDT, or SiOx.

1 January 1996 in Dental Materials Journal
Verified
Journal Article
Closed access
HOHiroki Ohno
Hiroki Ohno
YAYoshima Araki
Yoshima Araki
KEKazihiko Endo
Kazihiko Endo
YYYuro Yamane
Yuro Yamane
IKIsao Kawashima
Isao Kawashima
The water durability at adhesion interfaces was investigated by measurement of the peeled area of thin resin films bonded with 4-META resin on metal surfaces after imposing thermal stress using liquid nitrogen. Thermal stress at the adhesion interface was calculated by a computer-aided finite element method. On 18-8 stainless-steel specimens which bond strongly with 4-META resin, total interface failure occurs on specimens with resin thicker than 0.55 mm in dry condition. A resin layer of 0.25 mm was chosen to study degradation of the adhesion interface by water. The shearing stress was calculated as 16 MPa for a 0.25 mm thick resin layer. On mild-steel adherent interface with 4-META resin which degrades rapidly by water molecule, the relationship between water immersion time and degradation at the adhesion interface was discussed together with the amount of water penetrated at the interface. The method proposed in the present study is effective as a quick evaluation method for water durability at the adhesion interface.