10 April 2018 in IEEE Access
The widespread need for ubiquitous power delivery is driving the commercialization of inductive wireless power transfer (WPT). Wireless power transfer systems, however, are plagued by low efficiency. To combat this, we propose a new approach to maximize the efficiency of inductive WPT using multiple coil charging systems. The use of multiple coils can potentially allow the system to efficiently adapt to magnetic field propagation conditions, similar to the way multiple antennas are used to adapt to channel conditions in wireless communication systems. We consider a multiple-input single-output (MISO) WPT system using near-field inductive coupling. While such systems have been extensively studied in previous work using lumped resistance, inductance, and capacitance (RLC) circuit models to analyze their behavior, the difficulty of constructing tractable and realistic circuit models has limited the ability to accurately predict and optimize the performance of these systems. The main innovation in our work is to take a more abstract approach to modeling the WPT system as a linear circuit whose input-output relationship is expressed in terms of a small number of unknown parameters that can be thought of as transimpedances and gains. The crucial advantage of this approach is the economy of the representation, i.e., the number of unknown model parameters can be much smaller than the number of lumped circuit elements required for a complete and accurate RLC circuit representation. We present simple derivations for the optimal voltage excitations to be applied at the transmitters to maximize power transfer efficiency as well as suboptimal excitations which are less computationally intensive. A simple procedure, which we call circuit sounding, for estimating the unknown parameters using a small set of direct measurements is described. We outline a series of experiments with four transmit coils and two receive coils that verify the model and show that the optimal solution can achieve higher efficiencies than those of previously known methods.
24 September 2018 in IEEE Transactions on Wireless Communications
We consider the problem of optimal precoder design for a multi-input single-output wideband wireless system to maximize two different figures of merit: the total communication capacity and the total received power, subject to individual power constraints on each transmit element. We show that the two optimal precoders satisfy a Separation Principle that reveals a simple structure for these precoders. We use this Separation Principle extensively to derive several interesting properties of these two optimal precoders. Some key analytical results are as follows. We show that the power-maximizing precoders must concentrate all their energy in a small number of active channels that cannot exceed the number of input terminals. The capacitymaximizing precoder turns out to be very different from the classical waterfilling solutions and also very different from the power-maximizing precoders except at asymptotically low SNRs where the power-maximizing precoders also maximize capacity. We also show that the capacity of the wideband system is lowerbounded by the sum-rate of a multiple-access channel with the same channel gains and power constraints. Finally, the Separation Principle also yields simple fixed-point algorithms that allow for the efficient numerical computation of the two optimal precoders.
7 November 2016 in IEEE Transactions on Wireless Communications
We consider the problem of multicasting a common message signal from a distributed array of wireless transceivers by beamforming to a set of beam targets, while simultaneously protecting a set of null targets by nullforming to them. We describe a distributed algorithm in which each transmitter iteratively adapts its complex transmit weight using common aggregate feedback messages broadcast by the targets, and the local knowledge of only its own channel gains to the targets. This knowledge can be obtained using reciprocity without any explicit feedback. The algorithm minimizes the mean square error between the complex signal amplitudes at the targets and their desired values. We prove convergence of the algorithm, present geometric interpretations, characterize initializations that lead to minimum total transmit power, and prescribe designs for such initializations. We show that the convergence speed is nondecreasing in the number of transmitters N if a step size parameter is kept constant. For Rayleigh fading channels, as N goes to infinity: 1) convergence can be made arbitrarily fast and 2) beams and nulls can be achieved with vanishing total transmit power even with noise, both with probability one. These results add up to some remarkable scalability properties: the feedback overhead does not grow with the number of transmitters, and with high probability, the algorithm can be configured to converge arbitrarily fast and use vanishingly small total transmit power.
1 January 2011 in IFAC Proceedings Volumes