In order to clarify the potential of internal purification methods on medium speed diesel engines to meet the IMO Tier III nitrogen oxide (NOx) emission regulations, combined 1-D engine working cycle simulation and 3-D CFD simulation were conducted to predict the performance and emissions of the engine under different valve close timings, geometric compression ratios, injection timings, and Exhaust Gas Recirculation (EGR) rates. The numerical results show that, as the inlet valve close timing is advanced, NOx is reduced by as much as 27%, but the peak of premixed combustion heat release rate is increased; this can weaken the ability to reduce NOx with the Miller cycle. Moreover, the peak of premixed combustion heat release rate is reduced when the geometric compression ratio is increased to 15.4, and linking with injection timing by delaying 6°CA can further reduce NOx by 55.3% from the baseline. Finally, over 80% NOx reduction can be achieved when the above schemes are combined with over 15% EGR. The NOx and soot can be reduced simultaneously by using moderate Miller cycle combination with moderate EGR, and the results show a large reduction of NOx and moderate reduction of soot. This can be a feasible technical solution to meet Tier III regulations.
Low-temperature combustions (LTCs), such as homogeneous charge compression ignition (HCCI), could achieve high thermal efficiency and low engine emissions by combining the advantages of spark-ignited (SI) engines and compression-ignited (CI) engines. Robust control of the ignition timing, however, still remains a hurdle to practical use. A novel technology of jet-controlled compression ignition (JCCI) was proposed to solve the issue. JCCI combustion phasing was controlled by hot jet formed from pre-chamber spark-ignited combustion. Experiments were done on a modified high-speed marine engine for JCCI characteristics research. The JCCI principle was verified by operating the engine individually in the mode of JCCI and in the mode of no pre-chamber jet under low- and medium-load working conditions. Effects of pre-chamber spark timing and intake charge temperature on JCCI process were tested. It was proven that the combustion phasing of the JCCI engine was closely related to the pre-chamber spark timing. A 20 °C temperature change of intake charge only caused a 2° crank angle change of the start of combustion. Extremely low nitrogen oxides (NOx) emission was achieved by JCCI combustion while keeping high thermal efficiency. The JCCI could be a promising technology for dual-fuel marine engines.
29 December 2021 in International Journal of Engine Research
A variable valvetrain system is the key part of the variable stroke engine (VSE), which could achieve higher power performance and low-speed torque. An innovative axial shift valvetrain system (ASVS) was put forward to meet the air-charging requirements of a 2/4-stroke engine and complete a changeover within one working cycle. Two sets of intake and exhaust cam profiles for both intake and exhaust sides in the 2/4-stoke mode were designed for 2/4-stoke modes. Furthermore, a simulation model based on ADAMS was established to evaluate the dynamic valve motion and the contact force at different engine speeds. The dynamic simulation results show that the valve motion characteristics meet the challenges at the target engine speed of 3000 r/min. In two-stroke mode, the maximum intake valve lift could achieve 7.3 mm within 78°CaA, and the maximum exhaust valve lift could achieve 7.5 within 82°CaA on the exhaust side. In four-stroke mode, the maximum intake valve lift can achieve 8.8 mm within 140°CaA, and the maximum exhaust valve lift can achieve 8.4 mm within 140°CaA. The valve seating speeds are less than 0.3 m/s in both modes, and the fullness coefficients are more than 0.5 and 0.6 in the 2-stroke and 4-stroke mode, respectively. At the engine speed of 3000 r/min, the contact force on each component is acceptable, and the stress between cam and roller can meet the material requirement.
Methanol has attracted growing attention as a low-carbon alternative fuel for internal combustion engines. However, its low cetane number and high auto-ignition temperature pose significant challenges to achieving reliable ignition and efficient combustion in compression-ignition engines. To overcome these challenges, various advanced combustion strategies have been developed, among which glow plug-assisted ignition (GPAI) technology has emerged as an effective approach for initiating and sustaining methanol combustion under compression ignition conditions. This review systematically summarizes the recent advances in GPAI technology for methanol engines. The fundamental combustion strategies for methanol engines and the operating principles of GPAI are first introduced, followed by a comprehensive review of recent progress in GPAI methanol engines from the perspectives of engine performance, ignition characteristics, in-cylinder flame evolution, combustion behavior, and pollutant formation. This review highlights the critical role of the glow plug in promoting the formation of the initial ignition kernel and regulating subsequent combustion evolution in methanol engines. The existing literature demonstrates that GPAI technology can effectively facilitate methanol ignition and support high-efficiency combustion under compression ignition conditions. However, current research remains predominantly based on numerical simulations, while experimental investigations are relatively limited, particularly for large-bore engines. Overall, this review provides a comprehensive understanding of the ignition and combustion mechanisms of GPAI methanol engines and identifies key research needs to support their further development and practical application.
16 July 2026 in International Journal of Hydrogen Energy