4 December 2017 in IEEE Journal of Photovoltaics
The nonlinear characteristics of a photovoltaic (PV) array, maximum power point tracking of the PV inverter, presence of blocking diodes, and lower irradiation prevent the conventional protection devices to trip under certain faults and lead to reduced system efficiency and fire hazards. Moreover, the PV characteristics under certain partial shading conditions are similar to that under fault conditions. Hence, it is imperative to detect faults and differentiate faults from the partial shading condition to avoid false tripping of the system. This paper proposes a simple fault detection method using the available data of array voltage and current by means of wavelet packets. The proposed scheme is simulated using MATLAB/Simulink and is experimentally tested on a 1.6-kW $\text{4}\,\times \,\text{4}$ PV array to validate its performance .
27 April 2018 in IEEE Transactions on Energy Conversion
This paper presents a new Maximum Power Point Tracking (MPPT) technique for extracting the maximum power in Thermoelectric Generator (TEG) systems. Considering the linear nature of I-V characteristics of a TEG source, the proposed technique is based on the linear extrapolation principle. The I-V co-ordinates of two random operating points are used in computing the co-ordinates of new MPP. As anticipated, the proposed method involves only three sampling periods to reach the MPP under any dynamic conditions. The Linear Extrapolation based MPPT (LEMPPT) technique has several advantages such as simplicity of analysis, fixed and minimal convergence time, ease of implementation and a high tracking efficiency due to the absence of steady-state oscillations. Further, there is no need to interrupt the circuit for measuring the open-circuit voltage of TEG. Also, there is no requirement for additional switches or components. The simulation and test results show that the proposed algorithm has a superior performance as compared to that of the Perturb and Observe (P&O) algorithm.
1 July 2019 in IEEE Transactions on Power Electronics
This paper presents a simple dc-link voltage modulation scheme to minimize the commutation torque ripple in a Permanent Magnet Brushless DC Motor (PMBLDCM). Maintaining a constant current in the non-commutating (NC) phase helps to minimize the torque ripple, which can be achieved by boosting the motor input voltage whenever two phase currents are undergoing commutation. At low speeds, since the required ac voltage at commutation is also less than nominal, the standard PWM operation of inverter with the nominal dc-link voltage suffices. However, at higher speeds, a momentary (only during the commutation interval) boost in the dc-link voltage (above the nominal level) is needed to ensure boost in motor voltage, hence a steady current in the NC phase. In the proposed scheme, the dc voltage boost at higher speeds is obtained by connecting two capacitors in series which are normally connected in parallel across the dc-link. The proposed scheme is verified for a 1hp PMBLDCM drive through simulations and experiments in the laboratory. Results exhibit a notable improvement in reducing the torque ripple.
16 April 2020 in IEEE Transactions on Power Electronics
A major challenge in a Photovoltaic (PV) system is to identify the line-to-line (LL) faults that occurred under low irradiance conditions, during day-to-night/night-to-day transitions in the presence of blocking diodes. Due to active maximum power point tracker, these faults may not be identified and continue to be hidden even if the system returns to a high irradiance condition, since the magnitude of fault current may be less than the rating of the protection device (fuse). Those uncleared faults may subsequently lead to reduced peak output power, reliability issues and may even cause fire risks. To address these issues, a method is proposed to identify the pre-existing/undetected faults using the transitory conditions that occur during the pre-turn ON/OFF condition of the PV inverter (checking mode). From these transitory conditions, the I-V curve of the PV array is exploited without the need for additional components or sensors. Also, there is no need to disconnect the PV array from the setup. Moreover, the local minima is tracked, to discriminate the faults and partial shading conditions. The proposed algorithm is tested on a small-scale grid-connected PV system and implemented in LabVIEW. The results demonstrate the efficacy of proposed algorithm in detecting the pre-existing/undetected faults.
8 March 2017 in IEEE Journal of Emerging and Selected Topics in Power Electronics
This paper presents a detailed analysis of Type-3 phase locked loop (PLL) under wide variation in input voltage and frequency. Using small signal modeling, the performance of both single loop and dual loop Type-3 PLL for variation in input voltage and frequency is studied. The analysis shows that for the same bandwidth, both the single loop and dual loop Type-3 PLLs exhibit similar dynamics provided the supply voltage is balanced. However, under voltage sag conditions, dual loop PLL shows improved dynamic response without affecting its stability. Further, the tracking time is reduced as the feed forward frequency is a function of supply frequency. To improve the filtering characteristics under frequency deviations, a dual loop Type 3 adaptive PLL which accurately tracks the phase and frequency of the input signal under wide frequency deviations is developed. Simulations are carried out in MATLAB and experimentally verified by implementing in ALTERA cyclone II Field Programmable Gate Array (FPGA) board.
11 May 2015 in Electric Power Components and Systems
GIGanesan Saravana Ilango
ZLZachariah Varghese Lakaparampil
Zachariah Varghese Lakaparampil
—India is faced with the major challenges of (a) providing energy access to all its citizens, (b) heavy dependence on fuel imports for energy security, and (c) complying with international protocols on climate change mitigation, although the economic and social development is the foremost priority. The increase in energy demand due to growing population and industrialization in the face of depleting fossil fuel resources has stimulated the country's efforts in adopting power generation from renewable energy sources. Starting with 0.34 GW (2%) out of 17 GW of the country's total installed capacity in the year 2002, the share of renewable power generation has reached 31.7 GW (12.5%) of 250 GW as of 2014. In the aspect of total installed renewable power generation, India occupies the fifth position in the world today. While the governmental policies have steadily encouraged the adoption of renewable power generation, there is need and potential for more vigorous engagement in pursuit of achieving power for all citizens along with economic development. This article presents a brief review of emergence and growth of renewable power generation in India, wind and solar sectors in particular.