1 January 2011 in International Journal of Exergy
Thermodynamic analysis of a distillation column has important role for synthesising and developing energy-efficient distillation process. We have invented representation of this analysis to integrate characteristics of separation performance and exergy features of internal distillation column using Material-Utilisation Diagram (MUD). In this paper, we analyse separation performance and exergy loss phenomena for retrofitted distillation column, i.e., side heating–cooling and pump around in a distillation, on MUD. This MUD methodology displays Minimum Driving Force (MDF) for side heating-cooling and Close to Equilibrium Point (CEP) for pump-around system at a particular heat load.
28 September 2021 in Jurnal Teknologi (Sciences & Engineering)
Epoxides from vegetable oils are currently gaining more attention to replace petroleum-based monomers for polymer synthesis. As one of unsaturated fatty acids derived from vegetable oil, Oleic acid can be converted into epoxidized oleic acid by chemical epoxidation. Epoxidized oleic acid is a bifunctional monomer that has the potential to be used as raw material for fatty-acid-based polyester synthesis. This paper proposes the Taguchi-based optimization technique for in-situ epoxidation of oleic acid. The combining factors affecting the maximum yield were also determined to obtain a higher quality of epoxidized oleic acid in a relatively short time. Epoxidized oleic acid was characterized and tested for degradation. The characterization result showed the possibility of the polymerization reaction, and the kinetic study showed that the rate of epoxide degradation at room temperature follows second order with a reaction rate constant of2.7235 gr.mmol-1.day-1.
26 August 2015 in Advanced Materials Research
ZnO nanoflowers were synthesized by co-precipitation method at low temperature (80°C) for dye-sensitized solar cell applications. ZnO nanostructures were grown at various pH values from Zinc nitrate tetrahydrate [Zn (NO3)2.4H2O], HMTA (Hexamethylenetetramine) and Potassium Hydroxide (KOH). The results indicate that by increasing pH from 6 to 12, the ZnO morphology evolves from aggregrated particles, prism-like and eventually flower-like structures. According the Scherrer equation the particle size of (100), (002), and (101) peaks tends to drop as the pH increased. HMTA is known as an effective reductant to produce hexagonal ZnO rods of various lengths and cross-sections. Low HMTA led to smaller petal and further addition caused the petal became wider. Annealing temperature should not be higher than 200°C.
1 January 2020 in Journal of Oleo Science
Japan's largest platform for academic e-journals: J-STAGE is a full text database for reviewed academic papers published by Japanese societies
16 June 2023 in Jurnal Teknologi Bahan dan Barang Teknik
Reaksi epoksidasi mengubah ikatan rangkap pada senyawa olefin menjadi ikatan epoksida atau oksiran. Metil ester dari minyak nabati dengan kandungan asam lemak tak jenuh dapat digunakan sebagai bahan baku pada reaksi epoksidasi. Epoksida berbasis minyak nabati memiliki potensi yang besar untuk digunakan sebagai plasticizer untuk pemrosesan polimer. Pada penelitian ini, reaksi epoksidasi dilakukan secara in-situ menggunakan asam asetat, hidrogen peroksida, dan asam sulfat sebagai katalis. Rancangan eksperimen dengan Taguchi digunakan untuk optimasi kondisi reaksi yang meliputi suhu reaksi serta perbandingan molar hidrogen peroksida dan asam asetat terhadap metil oleat. Hasil optimasi menunjukkan bahwa faktor yang paling berpengaruh terhadap yield adalah perbandingan molar asam asetat terhadap asam oleat. Yield maksimum sebesar 79,87% diperoleh pada suhu 60°C dengan perbandingan molar hidrogen peroksida dan asam asetat terhadap metil oleat berturut-turut sebesar 1,6 dan 0,3.
24 August 2023 in Bulletin of Chemical Reaction Engineering & Catalysis
Epoxidized oleic acid can be transformed into vegetable oil-based polyesters through a self-polymerization reaction. This study aims to develop the kinetic model for the polymerization reaction between epoxide and carboxyl groups and the product characterization regarding its functional groups, molecular weight, and thermal stability. The polymerization reaction was carried out at the temperature of 120–180 °C for 2–6 h with the highest conversion of oxirane number up to 97%. Kinetic study showed one-step reaction model between oxirane and carboxylic group gives the activation energy value of 34.71 kJ/mol. Furthermore, the two simultaneous reaction model with further reaction between oxirane group and hydroxyl group also taken into account. The later provides a better agreement between the experimental data and the calculated conversion value. The activation energy values in the first and second steps are 38.61 and 26.00 kJ/mol, respectively. The product characterization showed that adding adipic acid did not significantly affect the polymer's molecular weight and thermal stability. The polydisperse characteristics of the poly(oleic acid) produced in this study enable poly(oleic acid) to be used as a lubricant, a polymer additive, or a precursor to produce polymers with higher molecular weights by taking advantage of the accessibility of OH groups. Copyright © 2023 by Authors, Published by BCREC Group. This is an open access article under the CC BY-SA License (https://creativecommons.org/licenses/by-sa/4.0).