Rochmadi Rochmadi

Rochmadi Rochmadi

Auto-generated profile, based on publicly available information

Rochmadi Rochmadi

Department of Chemical Engineering, Faculty of Engineering, Universitas Gadjah Mada, Jl. Grafika No. 2, Yogyakarta 55281, Indonesia

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
25 December 2021 in Energies
Verified
Journal Article
Open access
PDF file
AZAriany Zulkania
Ariany Zulkania
RRRochmadi Rochmadi
Rochmadi Rochmadi
MHMuslikhin - Hidayat
Muslikhin - Hidayat
RCRochim Bakti Cahyono
Rochim Bakti Cahyono
Currently, fossil fuels are still the primary fuel source and reducing agent in the steel industries. The utilization of fossil fuels is strongly associated with CO2 emissions. Therefore, an alternative solution for green steel production is highly recommended, with the use of biomass as a source of fuel and a reducing agent. Biomass’s growth consumes carbon dioxide from the atmosphere, which may be stored for variable amounts of time (carbon dioxide removal, or CDR). The pellets used in this study were prepared from a mixture of low-grade iron ore and palm kernel shells (PKS). The reducing reactivity of the pellets was investigated by combining thermogravimetric analysis (TGA) and laboratory experiments. In the TGA, the heating changes stably from room temperature to 950 °C with 5–15 °C/min heating rate. The laboratory experiments’ temperature and heating rate variations were 600–900 °C and 10–20 °C/min, respectively. Additionally, the reduction mechanism was observed based on the X-ray diffraction analysis of the pellets and the composition of the reduced gas. The study results show that increasing the heating rate will enhance the reduction reactivity comprehensively and shorten the reduction time. The phase change of Fe2O3 → Fe3O4 → FeO → Fe increases sharply starting at 800 °C. The XRD intensities of Fe compounds at a heating rate of 20 °C/min are higher than at 10 °C/min. Analysis of the reduced gas exhibits that carbon gasification begins to enlarge at a temperature of 800 °C, thereby increasing the rate of iron ore reduction. The combination of several analyses carried out shows that the reduction reaction of the mixture iron ore-PKS pellets runs optimally at a heating rate of 20 °C/min. In this heating rate, the reduced gas contains much higher CO than at the heating rate of 10 °C/min at temperatures above 800 °C, which encourages a more significant reduction rate. In addition, the same reduction degree can be achieved in a shorter time and at a lower temperature for a heating rate of 20 °C/min compared to 10 °C/min.

25 December 2021 in Processes
Verified
Journal Article
Open access
PDF file
MHMeiga Putri Wahyu Hardhianti
Meiga Putri Wahyu Hardhianti
RORochmadi
Rochmadi
MAMuhammad Mufti Azis
Muhammad Mufti Azis
Esterification of rosin with pentaerythritol produces rosin pentaerythritol ester (RPE) which is widely used in paint, coating, and pressure-sensitive and hot-melt adhesive industries. Although RPE has excellent valuable applications and has been industrially produced, studies on the reaction kinetics have not been widely reported in the present literature. This work proposed a kinetic study of RPE synthesis by including a series of consecutive reactions forming mono-, di-, tri-, and tetra-ester with decarboxylation of rosin as a side reaction in the kinetics model. For esterification, the reaction rates were determined by the second-order kinetic model. The first-order kinetic order was proposed for decarboxylation. Kinetic experiments were performed at a temperature range of 260 °C to 290 °C. The initial molar ratio of pentaerythritol to rosin (in the mole of OH/COOH) used was between 0.8 and 1.2. A small amount of samples were withdrawn in certain time interval. The sample was analyzed to evaluate their acid and saponification number. Afterward, those experimental data were used to simulate and validate the proposed kinetic model. In general, the proposed model could capture the experimental data well. The resulting activation energies ranged from 65.81 to 129.13 kJ mol−1 for esterification and 233.00 kJ mol−1 for decarboxylation. This model also offers a new insight that correlates well with tetra-ester formation and the softening point.

24 November 2021 in Molecules
Verified
Journal Article
Open access
PDF file
HKHersandy Dayu Kusuma
Hersandy Dayu Kusuma
RORochmadi
Rochmadi
IPImam Prasetyo
Imam Prasetyo
Teguh AriyantoTeguh Ariyanto
Teguh Ariyanto
This study explores the modification of lignin with surfactants, which can be used as a template to make mesoporous structures, and can also be used in combination with manganese oxide to produce manganese oxide/lignin-derived carbon. Organosolv extraction, using ethanol (70%) at 150 °C, was carried out to extract lignin from oil palm wood. Lignin was then mixed with Pluronic F-127, with and without Mn(NO3)2, and then crosslinked with acidic formaldehyde, resulting in a carbon precursor-based modified lignin. Carbonization was carried out at 900 °C to produce lignin-derived carbon and manganese oxide/lignin-derived carbon. The characterization materials included Fourier transform infrared (FTIR) spectroscopy, scanning electron microscope-energy dispersive X-ray (SEM-EDX) mapping, X-ray diffraction (XRD), and N2-sorption analysis. FTIR curves displayed the vibration bands of lignin and manganese oxide. SEM images exhibited the different morphological characteristics of carbon from LS120% (lignin with a Pluronic surfactant of 120%) and LS120%Mn20% (lignin with a Pluronic of 120% and Mn oxide of 20%). Carbon LS120% (C-LS120%) showed the highest specific surface area of 1425 m2/g with a mean pore size of 3.14 nm. The largest mean pore size of 5.23 nm with a specific surface area of 922 m2/g was exhibited by carbon LS120%-Mn20% (C-LS120%-Mn20%). C-LS120%Mn20% features two phases of Mn oxide crystals. The highest specific capacitance of 345 F/g was exhibited by C-LS120%-Mn20%.

18 November 2021 in International Journal of Renewable Energy Development
Verified
Journal Article
Open access
PDF file
WWWusana Agung Wibowo
Wusana Agung Wibowo
RCRochim Bakti Cahyono
Rochim Bakti Cahyono
RRRochmadi Rochmadi
Rochmadi Rochmadi
ABArief Budiman
Arief Budiman
The thermogravimetric behaviors and the kinetic parameters of uncatalyzed and catalyzed pyrolysis processes of a mixture of powdered raw rice husk (RRH) and its ash (RHA) in the form of pellets were determined by thermogravimetric analysis at three different heating rates, i.e., 5, 10, and 20 K/min, from 303 to 873 K. This research aimed to prove that the rice husk ash has a catalytic effect on rice husk pyrolysis. To investigate the catalytic effect of RHA, rice husk pellets (RHP) with the weight ratio of RRH:ARH of 10:2 were used as the sample. Model-free methods, namely Friedman (FR), Kissinger-Akahira-Sunose (KAS), and Flynn-Wall-Ozawa (FWO), were used to calculate the apparent energy of activation(EA). The thermogravimetric analysis showed that the decomposition of RHP in a nitrogen atmosphere could be divided into three stages: drying stage (303-443 K), the rapid decomposition stage (443-703 K), and the slow decomposition stage (703-873 K). The weight loss percentages of each stage for both uncatalyzed and catalyzed pyrolysis of RHP were 2.4-5.7%, 35.5-59.4%, and 2.9-12.2%, respectively. Using the FR, FWO, and KAS methods, the values of for the degrees of conversion (a) of 0.1 to 0.65 were in the range of 168-256 kJ/mol for the uncatalyzed pyrolysis and 97-204 kJ/mol for the catalyzed one. We found that the catalyzed pyrolysis led the to have values lower than those got by the uncatalyzed one. This phenomenon might prove that RHA has a catalytic effect on RHP pyrolysis by lowering the energy of activation.

28 September 2021 in Jurnal Teknologi (Sciences & Engineering)
Verified
Journal Article
Closed access
PDF file
DSDyah Retno Sawitri
Dyah Retno Sawitri
PMPanut Mulyono
Panut Mulyono
RRRochmadi Rochmadi
Rochmadi Rochmadi
ABArief Budiman
Arief Budiman
RORochmadi
Rochmadi
Epoxides from vegetable oils are currently gaining more attention to replace petroleum-based monomers for polymer synthesis. As one of unsaturated fatty acids derived from vegetable oil, Oleic acid can be converted into epoxidized oleic acid by chemical epoxidation. Epoxidized oleic acid is a bifunctional monomer that has the potential to be used as raw material for fatty-acid-based polyester synthesis. This paper proposes the Taguchi-based optimization technique for in-situ epoxidation of oleic acid. The combining factors affecting the maximum yield were also determined to obtain a higher quality of epoxidized oleic acid in a relatively short time. Epoxidized oleic acid was characterized and tested for degradation. The characterization result showed the possibility of the polymerization reaction, and the kinetic study showed that the rate of epoxide degradation at room temperature follows second order with a reaction rate constant of2.7235 gr.mmol-1.day-1.

23 September 2021 in Bulletin of Chemical Reaction Engineering & Catalysis
Verified
Journal Article
Open access
PDF file
MTMeutia Ermina Toif
Meutia Ermina Toif
MHMuslikhin Hidayat
Muslikhin Hidayat
RRRochmadi Rochmadi
Rochmadi Rochmadi
ABArief Budiman
Arief Budiman
Glucose is one of the primary derivative products from lignocellulosic biomass, which is abundantly available. Glucose has excellent potential to be converted into valuable compounds such as ethanol, sorbitol, gluconic acid, and levulinic acid (LA). Levulinic acid is an exceptionally promising green platform chemical. It comprises two functional groups, ketone and carboxylate, acting as highly reactive electrophiles for a nucleophilic attack. Therefore, it has extensive applications, including fuel additives, raw materials for the pharmaceutical industry, and cosmetics. This study reports the reaction kinetics of LA synthesis from glucose catalyzed by hydrochloric acid (HCl), a Bronsted acid, that was carried out under a wide range of operating conditions; i.e. the temperature of 140–180 °C, catalyst concentration of 0.5–1.5 M, and initial glucose concentration of 0.1–0.5 M. The highest LA yield of 48.34 % was able to be obtained from an initial glucose concentration of 0.1 M and by using 1 M HCl at 180 °C. The experimental results show that the Bronsted acid-catalyzed reaction pathway consists of glucose decomposition to levoglucosan (LG), conversion of LG to 5-hydroxymethylfurfural (HMF), and rehydration of HMF to LA. The experimental data yields a good fitting by assuming a first-order reaction model. Copyright © 2021 by Authors, Published by BCREC Group. This is an open access article under the CC BY-SA License (https://creativecommons.org/licenses/by-sa/4.0).