10 May 2018 in Journal of Physics D: Applied Physics
This work shows a promising approach to improve device performance by optimizing the electron transport and hole injection layers for tetraphenyldibenzoperiflanthene (DBP):rubrene-based red fluorescent organic light-emitting diodes (OLEDs). We compared the effect of two electron transport layers (ETLs), and found that the rubrene/bathophenanthroline (Bphen) ETL-based OLED showed a much higher external quantum efficiency (EQE) (4.67%) than the Alq3 ETL-based OLED (EQE of 3.08%). The doping ratio of DBP in rubrene was tuned from 1.0 wt% to 4.5 wt%, and the 1.5 wt%-DBP:rubrene-based OLED demonstrated the highest EQE of 5.24% and lowest turn-on voltage of 2.2 V. Atomic force microscopy images indicated that 1.5 wt% DBP-doped rubrene film exhibited a regular strip shape, and this regular surface was favorable to the hole and electron recombination in the emitting layer. Finally, the sorbitol-doped poly(3, 4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) was used to further improve the EQE; doping with 6 wt% sorbitol achieved the highest current efficiency of 7.03 cd A −1 and an EQE of 7.50%. The significantly enhanced performance implies that the hole injection is a limiting factor for DBP:rubrene-based red fluorescent OLEDs.
17 April 2019 in Journal of Physics D: Applied Physics
Doping poly(3,4-ethylenedioxythiophene):poly (styrene sulfonate) (PEDOT:PSS) by polar solvent is a promising approach to decrease the resistivity of pristine PEDOT:PSS film. In this work, properties of doped PEDOT:PSS films by a series of alcohol additives, including ethanol, glycerol, meso-erythritol, xylitol, and D-sorbitol, are comparatively studied for the first time. The absorption spectra, surface morphology, solvent contact angle, hole mobility, work function, and carrier transport properties via Hall measurement of these doped films were systematically investigated to find out the dopant dependent PEDOT:PSS film property. Then these low-resistivity PEDOT:PSS films were applied as the hole transport layer in 20 wt% poly(diketopyrro lopyrrole-terthiophene) (PDPP3T) based bulk heterojunctions (BHJs), and the highest power conversion efficiency (PCE) of 3.74% was achieved for the meso-erythritol doped PEDOT:PSS based BHJ, which is 21% higher than that (3.09%) of the pristine PEDOT:PSS based BHJ. Finally, the performance of all six BHJs is significantly improved by using lithium fluoride instead of bathocuproine, and the PCE for the meso-erythritol doped PEDOT:PSS based BHJ achieves 4.86%. Among these alcohol additives, meso-erythritol and D-sorbitol depict the optimum doping effect. Our results give important guidance to develop alcohol-additive doped PEDOT:PSS films in organic optoelectronic devices.
21 January 2019 in Nanotechnology
This work demonstrates effective performance improvement by simultaneous manipulating of the hole injection and electron transport layers for (4s,6s)-2,4,5,6-tetra(9H-carbazol-9-yl)isophthalonitrile (4CzIPN) based green thermally activated delayed fluorescent (TADF) organic light-emitting diodes (OLEDs). A 3 wt% sorbitol doped PEDOT:PSS layer results in the highest maximum current efficiency (CE max ) of 28.28 cd A –1 and external quantum efficiency (EQE) of 17.04%. Single carrier devices denote that hole mobility gradually rises with the sorbitol ratio. The electroluminescence mainly originates from the emission of 4CzIPN. Atomic force microscopy images imply that 3 wt% sorbitol doped PEDOT:PSS film includes the largest PEDOT aggregate, which contributes to a higher electric conductivity thus the better performance of 3 wt% sorbitol doped device. Also the 4CzIPN ratio in the emissive layer was optimized, and 4 wt%-4CzIPN in CBP achieves the highest EQE of 20.99% and CE max of 34.99 cd A –1 . The EL spectrum is independent of the luminous angle at a low 4CzIPN ratio but becomes more sensitive to the luminous angle at a high 4CzIPN ratio. Finally, we find out that the TADF OLED performance is very sensitive to TPBi thickness ranging from 20 nm to 65 nm, and 40 nm of TPBi achieves a CE max up to 64.10 cd A –1 and an excellent EQE of 25.14%, ascribing from its more balanced carrier transport.
1 October 2007 in Analytical Letters
The electrochemical behavior of Cu(II) was investigated on three‐dimensional 3‐mercaptopropionic acid (MPA) assembled on gold nanoparticle‐modified glassy carbon (GNP/GC) electrode. The results demonstrated that the MPA monolayer inhibited the charging current while promoted the response of accumulated Cu(II) on GNP/GC electrode. The effects of pH, scan rate, and accumulation time on the voltammetric behavior of Cu(II) on the MPA/GNP/GC electrode were studied. The MPA modified electrode presented a voltammetric response linearly proportional to the Cu(II) concentration from 0.1 µg/l to 100 µg/l, with a detection limit of 3.2 ng/l. Moreover, this electrode was successfully applied to the determination of Cu(II) in tap water.
30 October 2017 in Journal of Physics D: Applied Physics
To find the ideal acceptors for perovskite solar cells (PSCs) and get insight into the dielectric property at the interface between perovskite and acceptor, series of small molecular fullerene and non-fullerene acceptors were comparatively investigated. Fullerene acceptors based PSCs show higher performance than non-fullerene acceptors based PSCs. However, the perylene tetracarboxylic diimide based PSC has achieved a η PCE of 4.70%, implying that it is a promising acceptor candidate for PSCs because of its suitable energy level, high electron mobility, and smooth surface. By employing double acceptors of (6,6)-phenyl-C61-butyric acid methyl ester (PCBM)/C 60 or PCBM/3,4,9,10-perylenetetracarboxylic bisbenzimidazole, the PSC stability is greatly improved even without performance enhancement. The perovskite (Pero)/PCBM film shows smooth surface, suggesting that PCBM penetrates into the Pero layer. The hydrophobicity trend of Pero/acceptor composite films is same as the device performance by judging from the water contact angle, and Pero/PCBM as well as Pero/C 60 show higher hydrophobicity than other Pero/small-molecular-acceptor composite films. Capacitance–voltage characteristics of the series of single and double acceptor based PSCs were measured. The double acceptor based PSCs show larger depletion layer width ( W d ) than single acceptor based PSCs. Meanwhile, the defect density ( N A ) in Pero layer for single acceptor based PSCs is larger than that for double acceptor based PSCs, implying better n-doping of Pero layer by using a single acceptor.
20 August 2021 in Nanotechnology
Unlike the traditional fabrication of distributed Bragg reflector (DBR) structure via atomic layer deposition or spin-coating, here the 1–6 pairs of magnesium fluoride (MgF 2 )/zinc sulfide (ZnS) alternative dielectric layers were grown via thermal evaporation. The absorption, transmission, reflection, and photoluminescence (PL) spectra were evaluated. 5 pair MgF 2 /ZnS denotes the largest reflectance (88.5% at 535 nm) together with a stopband at 450–650 nm among the 1– 6 pair dielectric layers, exhibiting the potential for using as DBR. Relative to the bare 4,4’-bis(carbazol-9-yl)biphenyl(CBP):(4s,6s)−2,4,5,6-tetra(9H-carbazol-9-yl) isophthalonitrile (4CzIPN) film, the PL intensity of CBP:4CzIPN/5 pair MgF 2 /ZnS DBR is enhanced and splitted into two peaks. The 5 pair alternative dielectric film presents more uniform aggregation over 4 pair MgF 2 /ZnS. The cross-sectional scanning electron microscopic image denotes explicit layering for the MgF 2 and ZnS. The organic light-emitting diode (OLED) incorporating 5 pair MgF 2 /ZnS DBR layers illustrates significantly improved electroluminescent (EL) performance due to the photons concentrated in the direction perpendicular to the DBR. The slightly narrowed EL spectrum is originated from the microcavity effect between the two Al electrodes. Here we develop a universal method for the DBR fabrication suitable to most of OLEDs.