Himavarsha Dhulipati

Himavarsha Dhulipati

Auto-generated profile, based on publicly available information

Himavarsha Dhulipati

Department of Electronics, Carleton University, Ottawa, ON, Canada

Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
6 August 2019 in IEEE Transactions on Energy Conversion
Verified
Journal Article
Closed access
HDHimavarsha Dhulipati
Himavarsha Dhulipati
EGEshaan Ghosh
Eshaan Ghosh
SMShruthi Mukundan
Shruthi Mukundan
PKPhilip Korta
Philip Korta
JTJimi Tjong
Jimi Tjong
NKNarayan Chandra Kar
Narayan Chandra Kar
Few of the challenges with development of a single on–board motor for direct–drive electric vehicles include high torque density and low torque ripple. Therefore, in this paper, a 36–slot, 34–pole consequent pole six–phase permanent magnet synchronous machine (PMSM) has been optimized to address the aforementioned challenges for direct–drive application. Existing literature on optimization processes that rely solely on finite element models are restricted to three–phase machines only and also take longer computation time. Therefore, this paper proposes a novel optimization approach based on supervised machine learning for six–phase PMSM. In this approach, a non–conventional extended dual dq–frame model that accounts for higher order space harmonics in inductances and flux linkages has been developed and used for accurate computation of average torque and torque ripple of six–phase PMSM. Using the performance characteristics obtained from the extended dual dq–frame model for a set of initial design candidates, support vector regression algorithm is employed for supervised machine learning and increasing solutions in the design space. Furthermore, pareto front is used for selecting optimal machine models with maximum torque density and reduced torque ripple. Multi–objective trade–offs and comparison of initial and optimized designs based on average torque, torque ripple, efficiency and cost are performed.

24 September 2020 in IEEE Transactions on Magnetics
Verified
Journal Article
Closed access
HDHimavarsha Dhulipati
Himavarsha Dhulipati
SMShruthi Mukundan
Shruthi Mukundan
ZLZe Li
Ze Li
EGEshaan Ghosh
Eshaan Ghosh
JTJimi Tjong
Jimi Tjong
NKNarayan C. Kar
Narayan C. Kar
Developing a permanent magnet synchronous machine (PMSM) for direct–drive electric vehicle (EV) has challenges such as obtaining high torque density and low torque ripple. The PMSM should have high pole numbers owing to low–speed operation, thereby increasing the use of rare earth magnets and cost. Therefore, in this paper a consequent pole (CP) rotor topology is proposed in which the permanent magnet (PM) volume is reduced when compared with conventional surface PMSM (SPMSM). However, replacing south poles in an SPMSM with induced steel poles can increase torque ripple and reduce torque density. In order to improve torque density in a CP PMSM, structural modifications such as multilayer windings, non-ferromagnetic barriers have been proposed in the literature. These modifications increased the torque density while increasing the torque ripple. Therefore, this paper proposes a novel two-level optimization method based on gradient descent algorithm, to address the challenges of improving torque density and reducing torque ripple simultaneously in a CP PMSM. Initially, an expression for the magnet pole arc angle is derived for CP PMSM based on magnetic equivalent circuit. A two-level optimization is performed on a baseline CP PMSM to determine the optimal magnet pole arc. The torque production and torque ripples of the optimized design are validated by simulation and experimental results.

25 December 2019 in IEEE Transactions on Transportation Electrification
Verified
Journal Article
Closed access
ABAiswarya Balamurali
Aiswarya Balamurali
GFGuodong Feng
Guodong Feng
AKAnimesh Kundu
Animesh Kundu
HDHimavarsha Dhulipati
Himavarsha Dhulipati
NKNarayan C. Kar
Narayan C. Kar
This manuscript proposes improved mathematical models for torque and system efficiency used towards obtaining accurate current advance angle for maximizing the efficiency of an interior permanent magnet synchronous motor (IPM). Firstly, improved torque and efficiency calculation procedure that considers the effects of parameter variations such as inductance, stator resistance and PM flux linkage simultaneously and motor and inverter losses has been developed from a combination of analytical models and practical experiments. Subsequently, an offline search procedure has been utilized to determine optimal current angle using the improved dq axis – based models. The novelty of the efficiency model is that the method uses preliminary non- invasive experimental tests to consider the saturation and temperature effects simultaneously and successfully determines the relationship between stator and rotor temperatures by using only controller command voltages and currents. Experimental investigations are performed on a laboratory IPM for validating the developed control method through interpolation of improved look–up tables (LUT) with the derived current angle values for varying speed, torque and temperature conditions. The effectiveness of the proposed method in improving efficiency is also verified and compared with maximum efficiency and maximum torque per ampere methods using experimental sweep tests.

12 November 2018 in IEEE Transactions on Energy Conversion
Verified
Journal Article
Closed access
HDHimavarsha Dhulipati
Himavarsha Dhulipati
SMShruthi Mukundan
Shruthi Mukundan
CLChunyan Lai
Chunyan Lai
KMKaushik Mukherjee
Kaushik Mukherjee
JTJimi Tjong
Jimi Tjong
NKNarayan Chandra Kar
Narayan Chandra Kar
Permanent magnet (PM) synchronous machines (PMSMs) with concentrated windings (CW) exhibit high content of space harmonics leading to non-sinusoidal distribution of PM flux linkage and phase inductances in addition to the non-sinusoidal wave shape of the induced EMF. The ideal single reference frame based PMSM model considers these parameters to be sinusoidal and does not include the effect of harmonics. Hence, computation of electromagnetic torque using ideal model can lead to deviation from the actual waveform. In this paper, a novel analytical model for electromagnetic torque has been derived using multiple reference frames (MRF) incorporating non-sinusoidal aspects of CW PMSM. Initially, the PM flux linkage and inductances in abc frame are extended by incorporating higher order harmonics. Then, the extended model is transformed into dq-axis using MRF rotating at speeds of dominant harmonics in PM flux linkages and inductances, the fundamental being the electrical rotor frequency. Based on this MRF model, a comprehensive electromagnetic torque model for the CW PMSM is derived. Simulation and experiments are conducted on a CW PMSM to validate the proposed model under different operating conditions.

17 August 2018 in IEEE Transactions on Vehicular Technology
Verified
Journal Article
Closed access
LILakshmi Varaha Iyer
Lakshmi Varaha Iyer
CLChunyan Lai
Chunyan Lai
SMShruthi Mukundan
Shruthi Mukundan
HDHimavarsha Dhulipati
Himavarsha Dhulipati
KMKaushik Mukherjee
Kaushik Mukherjee
NKNarayan C. Kar
Narayan C. Kar
Power electronics and motor drive components existing in a conventional electric vehicle (EV) drivetrain employed to propel the EV can also be used to charge the battery under level 3 fast charging capacity. This integrated battery charging technology can be realized by employing the winding inductances of the three-phase interior permanent magnet synchronous motor (IPMSM) used for propulsion as line inductors while charging the EV's battery pack. The difference in the d- and q-axis inductances in the IPMSM offers unbalanced Thevenin impedances as viewed from stator terminals. This causes the voltages across the stator windings to become unbalanced when balanced three-phase currents synchronized with the grid utility voltages are forced into the three armature phases during charging. This paper first presents a case study employing a conventional laboratory IPMSM to illustrate the unbalanced phase winding impedance during an “emulated integrated charging” operation. Thereafter, the authors derive motivation to design and analyze an IPMSM with dampers in the rotor for propulsion and mitigation of the saliency effect, that is, the effect of unequal armature phase impedance at standstill during integrated charging. A novel design approach is presented and employed to design an IPMSM with dampers. Performance of the designed IPMSM with dampers is compared to that of the conventional IPMSM under both integrated charging and traction conditions. The proposed design is also validated experimentally using a laboratory IPMSM with dampers.

2 October 2018 in IEEE Transactions on Magnetics
Verified
Journal Article
Closed access
SMShruthi Mukundan
Shruthi Mukundan
HDHimavarsha Dhulipati
Himavarsha Dhulipati
JTJimi Tjong
Jimi Tjong
NKNarayan C. Kar
Narayan C. Kar
With advent in permanent magnet synchronous machine (PMSM) structure and inverter topologies, accurate parameter determination is of significance for high-performance control, analysis, and making critical decisions on inter-dependent design parameter variations for machine optimization. However, the machine parameters, including permanent magnet (PM) flux linkage and dq -axis inductances, vary during operation with machine nonlinearities such as magnetic saturation, temperature rise, and the introduction of spatial- and time-harmonic contents contributing toward inaccuracies during machine parameter determination. While classical dq -axis modeling fails to accommodate non-sinusoidal winding distributions and the effects of temperature rise, finite-element analysis (FEA) is computationally expensive and coupling of electromagnetic and thermal analysis including current harmonics becomes complex. Therefore, in this paper, a novel magnetic equivalent circuit model incorporating the effects of temperature rise and current harmonics has been developed for parameter determination of PMSMs. A lumped thermal model is implemented to determine the temperatures at each point of the machine. The proposed coupled electromagnetic and thermal model has been validated for various operating conditions of a fractional-slot distributed wound laboratory PMSM with FEA and experimental investigations.