Kuntawit Witthayolankowit

Kuntawit Witthayolankowit

Auto-generated profile, based on publicly available information

Kuntawit Witthayolankowit

Kasetsart University

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
20 June 2023 in Chemical Engineering Journal
Verified
Journal Article
Open access
KWKuntawit Witthayolankowit
Kuntawit Witthayolankowit
KBKiran Reddy Baddigam
Kiran Reddy Baddigam
DLDaria Lebedeva
Daria Lebedeva
MSManzoorahmed Shaikh
Manzoorahmed Shaikh
AKAnuja Kane
Anuja Kane
JSJoseph S.M. Samec
Joseph S.M. Samec

19 November 2023 in Journal of Natural Fibers
Verified
Journal Article
Open access
KWKuntawit Witthayolankowit
Kuntawit Witthayolankowit
JBJirachaya Boonyarit
Jirachaya Boonyarit
PSPreeyanuch Srichola
Preeyanuch Srichola
NRNattadon Rungruangkitkrai
Nattadon Rungruangkitkrai
TAThanyachol Apipatpapha
Thanyachol Apipatpapha
RCRungsima Chollakup
Rungsima Chollakup

1 October 2025
Verified
Book Chapter
Closed access
PDF file
PBPhacharaporn Bunyawanichakul
Phacharaporn Bunyawanichakul
Narongkorn KrajangsawasdiNarongkorn Krajangsawasdi
Narongkorn Krajangsawasdi
KWKuntawit Witthayolankowit
Kuntawit Witthayolankowit
WNWattanan Niwas
Wattanan Niwas
NCNopparuj Chongtrakool
Nopparuj Chongtrakool
RCRungsima Chollakup
Rungsima Chollakup

5 August 2026 in SSRN Electronic Journal
Verified
Preprint
Open access
NCNattapong Chantipmanee
Nattapong Chantipmanee
RKRattiwat Kamta
Rattiwat Kamta
KWKuntawit Witthayolankowit
Kuntawit Witthayolankowit
Rapid and reproducible protein determination is important for routine quality control of commercial protein powders. Although the bicinchoninic acid (BCA) assay is widely used because of its operational simplicity and broad working range, conventional batch procedures generally require prolonged incubation and multiple manual handling steps. In this study, an automated sequential injection analysis (SIA) system coupled with the BCA assay was developed and optimized for rapid total protein determination. The effects of sample loop volume, flow rate, working reagent (WR)-to-sample ratio, and incubation time were systematically investigated under dynamic flow conditions. The selected operating conditions comprised a 250 μL sample loop, a flow rate of 100 μL s⁻¹, a WR-to-sample ratio of 6:1, and a 3 min incubation period. Under these conditions, the method exhibited a linear response over 300–1300 μg mL⁻¹ with a coefficient of determination of 0.9997. The estimated limits of detection and quantification were 29.7 and 90.0 μg mL⁻¹, respectively, while intra- and interday precision were approximately 5% RSD or lower. The method was applied to three commercial protein. The obtained results were of a similar order to those produced by a manual batch BCA procedure. Relative to the conventional 8:1 WR-to-sample protocol, the optimized SIA procedure reduced the nominal working-reagent requirement by approximately 25%. A complete analytical cycle required approximately 4 min, corresponding to a throughput of approximately 15 samples h⁻¹. The proposed platform therefore provides a rapid, automated, and reagent-efficient approach to protein analysis while demonstrating the importance of flow-specific optimization when adapting conventional colorimetric assays to sequential injection systems.

8 October 2026 in SSRN Electronic Journal
Verified
Preprint
Open access
SCSirayu Chanpee
Sirayu Chanpee
SJSupachai Jadsadajerm
Supachai Jadsadajerm
KMKanit Manatura
Kanit Manatura
SWSutthipoj Wongrerkdee
Sutthipoj Wongrerkdee
WHWisa Homchan
Wisa Homchan
PAPornsawan Assawasaengrat
Pornsawan Assawasaengrat
Nanoporous carbon was produced from marine macroalgae (Rhizoclonium riparium) through pyrolysis, subsequently performing chemical activation with KOH at ratios between 1:1–1:5 for carbon dioxide (CO2) capture. The textural characteristics of the nanoporous carbon were assessed using nitrogen adsorption at -196 °C, while CO2 adsorption isotherms were evaluated at 0 °C and 25 °C. The non-linear density functional theory (NLDFT) was utilized to analyze the CO2 isotherms for the characterization of microporosity. The adsorption of CO2 on macroalgae-derived nanoporous carbon exhibited a high correlation with micropore volume and surface area. The synthesized materials demonstrated micropore volumes from 0.001-0.086 cm³/g and Brunauer–Emmett–Teller surface areas (SBET) spanning 1538.95-3247.67 m²/g. The nanoporous carbon with a 1:2 KOH ratio (MARC-800-1:2) had the maximum CO2 adsorption of 5.76 mmol/g at 0 °C. Simultaneously, the MARC-800-1:1 demonstrated the greatest absorption at 25 °C, recording a value of 3.76 mmol/g. Moreover, the studied nanoporous carbon exhibited a significant isosteric heat of adsorption, varying from approximately 29 to 15 kJ/mol, signifying robust interactions between CO2 molecules and the carbon surface.