Sumiko Fujisaki

Sumiko Fujisaki

Auto-generated profile, based on publicly available information

Sumiko Fujisaki

Research and Development Group, Hitachi, Ltd. 1 , 1-280 Higashi-Koigakubo, Kokubunji-shi, Tokyo 185-8601, Japan

Research Focus & Metrics

Academic Career Length

20Years (2007-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 September 2022 in Applied Physics Letters
Verified
Journal Article
Closed access
PDF file
SFSumiko Fujisaki
Sumiko Fujisaki
YYYoshihide Yamaguchi
Yoshihide Yamaguchi
HKHiroyuki Kobayashi
Hiroyuki Kobayashi
KSKazunori Shinoda
Kazunori Shinoda
MYMasaki Yamada
Masaki Yamada
MIMasaru Izawa
Masaru Izawa
Thermal-cyclic atomic layer etching of a Co film and a fine pattern with a smooth etched surface by plasma oxidation and organometallization is demonstrated. One cycle of the etching process consists of a two-temperature process. In the first step, plasma oxidation of Co is carried out at a low temperature of 25 °C to obtain a smooth Co oxide layer. In the second step, the Co oxide is organometallized with acetylacetone and desorbs at a high temperature of 210 °C that is suitable for organometallization and desorption. The etched amount per cycle is 0.6 nm, which is the same as the saturation amount of oxidation. A smooth etched surface is obtained after 20 cycles with a root mean square roughness of 0.53 nm, which is only slightly higher than the initial value of 0.34 nm. High etching selectivity over barrier metal of titanium-nitride was obtained. The two-step temperature cycle is crucial to achieve favorable etching with smooth etched surfaces.

1 December 2007 in IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control
Verified
Journal Article
Closed access
SFSumiko Fujisaki
Sumiko Fujisaki
YFYoshihisa Fujisaki
Yoshihisa Fujisaki
HIHiroshi Ishiwara
Hiroshi Ishiwara
Characteristics of metal-ferroelectrics-metal (MFM) capacitors and metal-ferroelectrics-insulator-semi-conductor (MFIS) diodes with poly(vinylidene fluoride-trifiuoroethylene) [P(VDF-TrFE)] copolymer films thinner than 100 nm were investigated. The films were prepared by spin-cast process and were annealed at 140degC in air for crystallization. The ferroelectric properties are equivalent to those of oxide ferroelectrics, even under low voltage or high frequency operation.

31 March 2007 in Applied Physics B
Verified
Journal Article
Closed access
PDF file
YLY. Lee
Y. Lee
STS. Tanaka
S. Tanaka
NUN. Uetake
N. Uetake
SFS. Fujisaki
S. Fujisaki
RIR. Inoue
R. Inoue
Masayoshi TonouchiMasayoshi Tonouchi
Masayoshi Tonouchi

1 April 2024 in AIP Advances
Verified
Journal Article
Open access
PDF file
SFSumiko Fujisaki
Sumiko Fujisaki
YYYoshihide Yamaguchi
Yoshihide Yamaguchi
HKHiroyuki Kobayashi
Hiroyuki Kobayashi
KSKazunori Shinoda
Kazunori Shinoda
MYMasaki Yamada
Masaki Yamada
MIMasaru Izawa
Masaru Izawa
Thermal-cyclic atomic layer etching of Co blanket film and a fine pattern by plasma oxidation and organometallization were investigated. To obtain a smoothly etched surface and self-limiting etching, a two-step temperature-etching process was used. Co was first oxidized using O2 plasma at a low temperature of 25 °C. Then, the Co oxide formed in the first step was organometallized with acetylacetone (acacH) and sublimed at a high temperature of 210 °C, which is appropriate for organometallization and sublimation. The etched amount per cycle was 0.6 nm. This value is the same as the saturated oxidation amount. The root-mean-square roughness after 20-cycle etching was 0.53 nm, and an atomically smooth etched surface was obtained. From the x-ray photoelectron spectroscopy (XPS) analysis, the oxidation state of Co oxide with a 530-eV O1s peak was dominant for organometallization with acacH. As the temperature increased, the O1s XPS peak of the Co oxide shifted lower to 529 eV and formed a columnar-shaped oxide. However, with acacH, oxide was organometallized when the O1s peak was at 530 eV.