Temporal characteristics of two-dimensional (2D) spatial images of a net production rate in a capacitively coupled plasma (CCP) reactor driven at high frequency (13.56 MHz) are investigated by newly developed computer-assisted optical emission tomography. Typical examples are presented for the absolute net formation rate of Ar(3p5) in Ar for 2 Torr and 13.56 MHz. The tomographic imaging enables us to understand a complex radial discharge structure in a CCP reactor, as well as in the central axial region.
1 August 2012 in Japanese Journal of Applied Physics
A newly designed microwave electron cyclotron resonance (ECR) plasma etching reactor has been developed for 450 mm wafer processing. The etching rates of polycrystalline silicon (poly-Si) and SiO2 across the wafer were evaluated as a function of ECR position. Two-dimensional (radial and vertical) distributions of the ion flux in the reactor were also investigated using a movable single probe system. A ring-shaped region of high-density plasma along the ECR plane was observed. This reveals the mechanism that the etching-rate distribution could be controlled by the ECR position. As a result, a polycrystalline silicon etching rate uniformity of 1.5% across a wafer was successfully obtained. Furthermore, the uniformity control of critical dimensions (CDs) based on wafer temperature was also investigated, and CD uniformity below 3 nm across the wafer was obtained in the optimum temperature distribution.
Thermal-cyclic atomic layer etching of Co blanket film and a fine pattern by plasma oxidation and organometallization were investigated. To obtain a smoothly etched surface and self-limiting etching, a two-step temperature-etching process was used. Co was first oxidized using O2 plasma at a low temperature of 25 °C. Then, the Co oxide formed in the first step was organometallized with acetylacetone (acacH) and sublimed at a high temperature of 210 °C, which is appropriate for organometallization and sublimation. The etched amount per cycle was 0.6 nm. This value is the same as the saturated oxidation amount. The root-mean-square roughness after 20-cycle etching was 0.53 nm, and an atomically smooth etched surface was obtained. From the x-ray photoelectron spectroscopy (XPS) analysis, the oxidation state of Co oxide with a 530-eV O1s peak was dominant for organometallization with acacH. As the temperature increased, the O1s XPS peak of the Co oxide shifted lower to 529 eV and formed a columnar-shaped oxide. However, with acacH, oxide was organometallized when the O1s peak was at 530 eV.
12 January 2026 in Journal of Vacuum Science & Technology A
Self-limiting thermal-cyclic etching of SiGe films demonstrating etch selectivity over Ge was achieved using alternating exposure to radicals generated in CHF3/N2/O2 plasma and infrared heating. Si, Ge, and SiGe with Ge contents from 25% to 70% were used as sample materials. In situ x-ray photoelectron spectroscopy revealed a N 1s peak attributed to N-H bonds after radical exposure to SiGe and Ge. The peak disappeared upon heating to 100 °C, indicating removal of the surface-modified layer. Cyclic etching of SiGe and Ge using a dry chemical removal tool shows thickness reduction with increasing cycles. The etch per cycle (EPC) for SiGe ranged from 3 to 7 nm, while that for Ge was 1–2 nm. Si was continuously etched. Saturation behavior with respect to radical exposure time was observed for both SiGe and Ge. Enhanced EPC of SiGe over Ge is attributed to the selective formation of the modified layer on SiGe surfaces.
1 August 2012 in Japanese Journal of Applied Physics
A newly designed microwave electron cyclotron resonance (ECR) plasma etching reactor has been developed for 450 mm wafer processing. The etching rates of polycrystalline silicon (poly-Si) and SiO2across the wafer were evaluated as a function of ECR position. Two-dimensional (radial and vertical) distributions of the ion flux in the reactor were also investigated using a movable single probe system. A ring-shaped region of high-density plasma along the ECR plane was observed. This reveals the mechanism that the etching-rate distribution could be controlled by the ECR position. As a result, a polycrystalline silicon etching rate uniformity of 1.5% across a wafer was successfully obtained. Furthermore, the uniformity control of critical dimensions (CDs) based on wafer temperature was also investigated, and CD uniformity below 3 nm across the wafer was obtained in the optimum temperature distribution.
1 September 2006 in 2006 IEEE International Symposium on Semiconductor Manufacturing
We have developed a fab-wide APC system to control critical dimension (CD) of gate electrode length. We have also developed a model equation to predict gate CD by considering the structures of gate electrode and STI. This prediction model was also used to do factor analysis of gate CD variation. Effectiveness of the prediction model for feedforward control was evaluated by both simulation and experiment.