19 September 2024 in IEEE Transactions on Transportation Electrification
Compound disturbances in steer-by-wire (SbW) include non-periodic disturbances in the mechanical system and periodic torque ripple in the permanent magnet synchronous motor (PMSM). Compound disturbances lead to degradation of control accuracy and robustness, with repeated deviations in tracking accuracy. Moreover, according to the time-varying conditions of SbW, the frequency of periodic disturbances varies over time. To this end, this paper proposes a compound disturbances suppression strategy that combines spatial domain iterative learning with forgetting factor (SILCFF) and extended state observer (ESO). ESO compensates the non-periodic disturbances to the non-singular fast terminal sliding mode controller (NFTSMC) to track the steering angle and reduce the unknown disturbance boundaries. After disturbance compensation, the system is approximately linearized, making it more suitable for SILCFF designs. SILCFF solves the problem of time-varying iteration cycles caused by the variable speed conditions of SbW, which is difficult to handle by conventional time-domain iterative learning, and compensates for periodic torque ripple. The results indicate that SILCFF can effectively compensate for periodic torque ripple at time-varying frequencies. This strategy can ensure the SbW system has good dynamic steering angle tracking performance and robustness.
4 February 2025 in IEEE Transactions on Intelligent Transportation Systems
We will apply dual three-phase permanent magnet synchronous motors (DTP-PMSM) to the road sensing unit of the steer-by-wire system to improve redundancy and fault tolerance performance, meeting the requirements of intelligent transportation systems. However, open circuit faults inevitably lead to periodic torque ripple, parameter mismatch, and current harmonics, which pose a huge threat to drivers and traffic participants. Therefore, this article proposes a dynamic balancing strategy that can operate stably under both motor health and fault conditions. Firstly, this strategy does not require diagnostic fault information, thereby fundamentally avoiding performance degradation caused by diagnostic accuracy, time, model reconstruction, and strategy switching. The torque control module (TCM) is based on adaptive iterative learning control with a forgetting factor, which achieves torque tracking and suppression of periodic ripple after faults. The current control module (CCM) is based on ultra local model free predictive current control and extended state observer to track current and suppress the effects of parameter mismatch and current harmonics. Based on the multi-variable multi-objective sliding mode extreme value search strategy, the internal parameters and external weights of the two modules are dynamically adjusted to achieve dynamic balance between health and fault operation of TCM and CCM. The experimental results show that this strategy effectively improves the robustness of the system in a healthy state and the fault tolerance performance in a faulty state, effectively suppressing the periodic torque ripple and current harmonics caused by faults. Compared with the dynamic balancing strategy based on NSGA-II, this strategy increases the THD of torque by 13.45% and reduces the THD of current harmonics by 9.83%.
27 June 2025 in IEEE Transactions on Intelligent Transportation Systems
Four-Wheel Independent Steering (4WIS) vehicles can independently control each wheel angle to achieve multiple steering modes, thereby expanding their motion space. However, existing trajectories do not match the multiple steering modes, making it difficult to leverage the stability of same-direction steering and the agility of opposite-direction steering of the front and rear wheels. This results in 4WIS vehicles facing challenges in generating trajectories that balance flexibility and stability under emergency obstacle avoidance scenarios. To address this, this manuscript proposes a multi-mode trajectory planning method for 4WIS vehicles under emergency obstacle avoidance scenarios. It decomposes the multiple steering modes of 4WIS vehicles into stable side-move motion and flexible yaw motion. By integrating these two motions, we establish a comprehensive kinematic model for 4WIS multi-mode operation. Based on this, the method combines side-move and yaw motions to construct a multi-mode risk field. The field is then iteratively optimized by the ILQR-MPC method to generate obstacle avoidance trajectories with sideslip and yaw angles, providing reference for the side-move and yaw motions across the multiple steering modes. Results show that the proposed method can generate trajectories that balance flexibility and stability, providing a foundation for safe and efficient obstacle avoidance.
19 March 2026 in IEEE Transactions on Automation Science and Engineering
The development of intelligent driving and steer-by-wire (SBW) technologies has increased the computational complexity and the number of CAN bus nodes in SBW vehicles, leading to the presence of significant time-varying CAN network time delay (TV-CAN-TD) in the control inputs of the SBW system. For dual-motor steer-by-wire (DMSBW) vehicles, TV-CAN-TD not only severely affects vehicle stability but also further deteriorates the synchronization performance of two motors, potentially causing accidents. To ensure vehicle safety under TV-CAN-TD conditions, a hierarchical time delay control strategy is proposed. For the upper-level controller, a TD-H₂/H∞ mixed sensitivity stability controller is designed. Based on the operational mechanism of the CAN network, the random time delay uncertainties in the vehicle's lateral dynamics model are modeled in detail using a polytope model. Combined with H₂/H∞ robust control, the controller mitigates the adverse effects of time delay uncertainties on vehicle stability. For the lower-level controller, a synchronization strategy that combines the novel reaching law sliding mode control with a cross-coupling synchronization structure is designed to ensure synchronization performance under TV-CAN-TD conditions. Simulations and hardware-in-the-loop experiments demonstrate that the proposed hierarchical control strategy effectively enhances the stability and synchronization performance of the DMSBW vehicle under TV-CAN-TD.
9 May 2025 in Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering
This study presents a piezoelectric energy harvester (PEH) integrated behind the suspension dampers of smart vehicles, employing vortex-induced vibration (VIV) to harvest wind energy for microsystem power supply. Through systematic investigation of spring-induced windbreak effects, we quantitatively analyzed the correlation between spring compression levels and vortex generation dynamics using suspension travel characteristic tests and confined flow field simulations. Building upon these findings, we developed an equivalent variable cross-section cylinder model to simplify the suspension mechanism. Comprehensive finite element simulations were conducted to elucidate the vortex shedding characteristics and formation mechanisms in the wake of variable-geometry cylindrical structures within bounded flow fields. To enhance energy conversion efficiency, we implemented electrode coverage optimization and impedance matching strategies, effectively reducing piezoelectric losses. These optimizations were systematically validated through multiphysics simulations (COMSOL), bench excitation tests, and hydrodynamic experiments. The PEH’s operational efficacy was further demonstrated through constrained wind tunnel testing and on-road vehicle trials, achieving respective output voltages of 73 and 81 mV under distinct airflow conditions: one featuring lateral wind with turbulence interference, and another under controlled laminar flow conditions.
19 January 2026 in Control Engineering Practice