Yukai Chu

Yukai Chu

Auto-generated profile, based on publicly available information

Yukai Chu

Department of Vehicle Engineering, Nanjing University of Aeronautics and Astronautics, Nanjing, China

Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
7 August 2024 in IEEE Transactions on Intelligent Transportation Systems
Verified
Journal Article
Closed access
YCYukai Chu
Yukai Chu
CWChunyan Wang
Chunyan Wang
XZXiaochuan Zhou
Xiaochuan Zhou
ZZZiyu Zhang
Ziyu Zhang
WZWanzhong Zhao
Wanzhong Zhao
Compared with other steering systems, Four-Wheel Independent Steering (4WIS) can control not only yaw motion but also their unique side-move motion to provide intelligent vehicles with stronger trajectory tracking capabilities. However, existing 4WIS wheel angle control often aims at zeroing the sideslip angle of the Center of Gravity (CoG), which inhibits the unique side-move motion of 4WIS vehicles. Especially under large-curvature turning conditions, relying only on yaw motion, the system is prone to entering a state of nonlinear instability; its trajectory tracking accuracy and stability are difficult to guarantee. In response, this paper proposes a 4WIS vehicle instantaneous center of rotation (ICR) tracking control method under large-curvature turning conditions. It converts traditional wheel angle control into ICR control. Through the coordinated control of side-move and yaw motion, trajectory tracking accuracy and stability are ensured under large-curvature turning conditions. The proposed ICR tracking control includes two parts: ICR control and trajectory decomposition. ICR control constructs a polar coordinate system with the vehicle CoG as the pole and establishes a decoupled mapping of side-move and yaw motion to the ICR. By predicting and optimizing the deviation between the ICR and its reference, the side-move and yaw motions are coordinated to achieve effective tracking of large curvature trajectories. Trajectory decomposition mainly converts the trajectory tracking target into the ICR control reference. By combining the particle model and trajectory curvature, polar coordinates are used to decompose the trajectory curvature into side-move and yaw curvatures, and through rolling optimization of lateral and heading errors, the target trajectory is decomposed into side-move and yaw control reference. HIL experimental results show that the proposed ICR tracking control strategy can effectively improve the trajectory tracking performance of 4WIS vehicles under large-curvature turning conditions.

30 September 2024 in IEEE Transactions on Transportation Electrification
Verified
Journal Article
Closed access
XZXiaochuan Zhou
Xiaochuan Zhou
WZWanzhong Zhao
Wanzhong Zhao
CWChunyan Wang
Chunyan Wang
YWYunqi Wang
Yunqi Wang
YCYukai Chu
Yukai Chu
X-by-wire chassis plays an important role in intelligent vehicle motion control. However, the traditional deterministic optimization method is difficult to achieve the global optimal and robust comprehensive performance of the chassis due to the multidisciplinary coupling relationship and uncertainties among steering, suspension and drive subsystems. This paper proposed a multidisciplinary optimization design framework incorporating the coupling relationship and uncertainties of structural parameters into the X-by-wire chassis. First, the dynamics models of hub motor driving, differential steering and semi-active suspension were established. Based on energy, safety and ergonomic, the performance indicators of the X-by-wire chassis were deduced and quantified. Second, the coupling relationship and the influence of uncertain factors on the reliability of constraints were analyzed by Monte Carlo and 6-Sigma methods. The Uncertain Bi-Level Collaborative Optimization (UBLCO) was proposed by integrating uncertainty analysis and Bi-Level Integrated System Collaborative Optimization. The proposed framework can ensure constraint reliability at the system level, allocate design variables to subsystems based on parameter coupling and uncertainty analysis, and achieve discipline decoupling through parallel optimization. The optimization results showed that UBLCO could effectively improve the reliability and robustness of the chassis performance under uncertainty. Finally, both the effectiveness and feasibility of the uncertain multidisciplinary optimization in X-by-wire chassis were further verified through the road tests, which is expected to provide a reference for the comprehensive design of the X-by-wire chassis of electric vehicles.

4 February 2025 in IEEE Transactions on Intelligent Transportation Systems
Verified
Journal Article
Closed access
HSHaoyu Sun
Haoyu Sun
WZWanzhong Zhao
Wanzhong Zhao
CWChunyan Wang
Chunyan Wang
ZLZhongkai Luan
Zhongkai Luan
WLWeihe Liang
Weihe Liang
HHHeng Huang
Heng Huang
We will apply dual three-phase permanent magnet synchronous motors (DTP-PMSM) to the road sensing unit of the steer-by-wire system to improve redundancy and fault tolerance performance, meeting the requirements of intelligent transportation systems. However, open circuit faults inevitably lead to periodic torque ripple, parameter mismatch, and current harmonics, which pose a huge threat to drivers and traffic participants. Therefore, this article proposes a dynamic balancing strategy that can operate stably under both motor health and fault conditions. Firstly, this strategy does not require diagnostic fault information, thereby fundamentally avoiding performance degradation caused by diagnostic accuracy, time, model reconstruction, and strategy switching. The torque control module (TCM) is based on adaptive iterative learning control with a forgetting factor, which achieves torque tracking and suppression of periodic ripple after faults. The current control module (CCM) is based on ultra local model free predictive current control and extended state observer to track current and suppress the effects of parameter mismatch and current harmonics. Based on the multi-variable multi-objective sliding mode extreme value search strategy, the internal parameters and external weights of the two modules are dynamically adjusted to achieve dynamic balance between health and fault operation of TCM and CCM. The experimental results show that this strategy effectively improves the robustness of the system in a healthy state and the fault tolerance performance in a faulty state, effectively suppressing the periodic torque ripple and current harmonics caused by faults. Compared with the dynamic balancing strategy based on NSGA-II, this strategy increases the THD of torque by 13.45% and reduces the THD of current harmonics by 9.83%.

15 October 2025 in IEEE/ASME Transactions on Mechatronics
Verified
Journal Article
Closed access
YCYukai Chu
Yukai Chu
CWChunyan Wang
Chunyan Wang
XZXiaochuan Zhou
Xiaochuan Zhou
ZZZiyu Zhang
Ziyu Zhang
ZLZhongkai Luan
Zhongkai Luan
WZWanzhong Zhao
Wanzhong Zhao
Addressing the challenges of existing wheel angle control methods that fail to fully utilize the side-move and yaw motions of four-wheel independent steering (4WIS) vehicles and struggle to balance stability and trajectory tracking accuracy during high-speed turns, this article proposes a dynamic stability domain expansion and instantaneous center of rotation (ICR) tracking control method for 4WIS vehicles. It includes three modules: ICR control model establishment, stability domain expansion and quantification, and controller design. The ICR control model transforms vehicle states into ICR states, converting traditional wheel angle control into ICR control in polar coordinates. By regulating side-move and yaw motion through ICR, four-wheel angles are allocated. Based on this, the second module uses the limiting ICR states of the 4WIS vehicle to define the global dynamic stability domain, expanding its boundaries to constrain ICR positions, and designing an energy ellipse to quantify vehicle stability to allocating ICR reference. An ICR tracking controller is then designed by integrating the ICR control model. Hardware-in-the-loop experiments confirm that the proposed method ensures precise and stable trajectory tracking for 4WIS vehicles during high-speed turns.

27 June 2025 in IEEE Transactions on Intelligent Transportation Systems
Verified
Journal Article
Closed access
YCYukai Chu
Yukai Chu
WZWanzhong Zhao
Wanzhong Zhao
XZXiaochuan Zhou
Xiaochuan Zhou
ZZZiyu Zhang
Ziyu Zhang
ZLZhongkai Luan
Zhongkai Luan
HSHaoyu Sun
Haoyu Sun
Four-Wheel Independent Steering (4WIS) vehicles can independently control each wheel angle to achieve multiple steering modes, thereby expanding their motion space. However, existing trajectories do not match the multiple steering modes, making it difficult to leverage the stability of same-direction steering and the agility of opposite-direction steering of the front and rear wheels. This results in 4WIS vehicles facing challenges in generating trajectories that balance flexibility and stability under emergency obstacle avoidance scenarios. To address this, this manuscript proposes a multi-mode trajectory planning method for 4WIS vehicles under emergency obstacle avoidance scenarios. It decomposes the multiple steering modes of 4WIS vehicles into stable side-move motion and flexible yaw motion. By integrating these two motions, we establish a comprehensive kinematic model for 4WIS multi-mode operation. Based on this, the method combines side-move and yaw motions to construct a multi-mode risk field. The field is then iteratively optimized by the ILQR-MPC method to generate obstacle avoidance trajectories with sideslip and yaw angles, providing reference for the side-move and yaw motions across the multiple steering modes. Results show that the proposed method can generate trajectories that balance flexibility and stability, providing a foundation for safe and efficient obstacle avoidance.

19 January 2026 in Engineering Applications of Artificial Intelligence
Verified
Journal Article
Closed access
YCYukai Chu
Yukai Chu
CWChunyan Wang
Chunyan Wang
XZXiaochuan Zhou
Xiaochuan Zhou
ZZZiyu Zhang
Ziyu Zhang
ZLZhongkai Luan
Zhongkai Luan
WZWanzhong Zhao
Wanzhong Zhao