29 June 2010 in Measurement Science and Technology
15 November 2013 in International Journal of Structural Integrity
Purpose: – The present paper aims to characterize the fatigue crack propagation behavior of wheel and rail steels, in particular the AVE wheel steel and an UIC60 rail steel, including several R-values and near threshold behavior. To accomplish this objective, mode I fatigue crack growth tests were performed according to the ASTM E647 standard on C(T) specimens taken from a Spanish high-speed AVE train used wheel and a UIC60 rail, tested with 0.1, 0.4 and 0.7 load ratios. Design/methodology/approach: – In the present study, the two different methodologies presented in the ASTM E647 standard were used to characterize the fatigue crack propagation behavior of the two studied materials. The K-decreasing test procedure was used to characterize fatigue crack propagation near the threshold, whereas the K-increasing with constant load range method was used in the Paris law regime. Findings: – It was observed that for the wheel a small influence of R-ratio was found, with greater R implying higher fatigue crack growth rates. For the rail, the influence is small, and for large values of ΔK, it is slightly reversed. The near-threshold results obtained indicate lower threshold values for higher R-ratio, a fact that is possibly associated with crack closure phenomena. A scanning electron microscope (SEM) study of fatigue crack propagation surfaces identified a random behavior in the striation orientation for both materials and no correlation was found between striation spacing and actual fatigue crack growth rate. Originality/value: – R-ratio and threshold behavior of fatigue crack propagation of a steel used in high-speed train wheels, as well as of UIC60 rail steel, were studied, with the objective of generating data to be used in maintenance and damage tolerance models.
1 August 2014 in Advanced Materials Research
Rolling contact fatigue twin-disc tests were performed on rail/wheel steels from Spanish high velocity trains (AVE). Residual stress profiles were determined using X-ray diffraction before and after cyclic loading. The evolution of residual stress profiles, due to cyclic loading, was analysed in order to study how they affect the rolling contact fatigue behaviour of these materials. This study is included in a major project where other related phenomena and materials’ properties have been studied.
12 January 2010 in Materials Science Forum
Great interest is dedicated to the wheel/rail contact problem, in particular as a result of some accidents worldwide and also in Portugal. In the present work a three dimensional finite element analysis of the wheel/ rail contact problem was performed using the software ABAQUS. A preliminary study on simpler geometries was carried out, in order to identify the solution strategies giving more accurate solutions. The influence of mesh refinement, friction coefficient, and numerical techniques as Lagrange and penalty functions were analysed in the simpler cases of contact of two cylinders along a generatrix, and the contact of a cylinder and a rigid plane. The corresponding Hertz solutions were programmed using MATLAB in order to compare with the finite element analyses. The numerical procedures giving better results were later applied to the wheel/rail contact problem, using standard rail and wheels profiles used by the Portuguese Railways company (CP). The influence of small geometry variations on the stress analysis results was then studied, and the study of initiation of defects using the Dang Van fatigue criterion was performed.
1 September 2013 in Materials Science Forum
Twin disc tribological tests were performed in wheel and rail materials, with specimens taken from a Spanish AVE train wheel and a UIC60 rail, in a program intended to characterize their contact fatigue behavior. The X-ray diffraction technique was used to characterize the residual stress distribution at the initial and damaged stages, as well as in intermediate stages, since existing residual stresses in the surface layers of the railways steels and its evolution during contact loading can have a major influence on crack initiation and propagation.
12 November 2012 in Materials Science Forum
The present work intends to evaluate, using simple, exemplary cases, the importance of a full elasto-plastic analysis in fatigue design. A strain cycling situation (-ε to ε) was modelled with ABAQUS considering two situations: firstly a linear σ vs. ε relationship was assumed, and secondly, the real cyclic σ vs. ε curve was used to model each cycle, which includes a small plastic deformation. The case of change of cross section in a steel shaft subjected to constant torsion and cyclic bending was analysed through finite element modelling using ABAQUS.