Daniel Belo

Daniel Belo

Auto-generated profile, based on publicly available information

Daniel Belo

Departamento de Eletrónica, Telecomunicações e Informática, Instituto de Telecomunicações, Universidade de Aveiro, 3810-193 Aveiro, Portugal

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
3 April 2023 in IEEE Journal of Microwaves
Verified
Journal Article
Open access
KNKyriaki Niotaki
Kyriaki Niotaki
Nuno CarvalhoNuno Carvalho
Nuno Carvalho
Apostolos GeorgiadisApostolos Georgiadis
Apostolos Georgiadis
Xiaoqiang GuXiaoqiang Gu
Xiaoqiang Gu
SHSimon Hemour
Simon Hemour
NSNaoki Shinoara
Naoki Shinoara
Radio frequency (RF) energy harvesting and wireless power transmission (WPT) technologies —both near-field and far-field—have attracted significant interest for wireless applications and RFID systems. We already utilize near-field WPT products in our life and it is expected that RF EH and far-field WPT systems can drive the future low-power wireless systems. In this article, we initially present a brief historical overview of these technologies. The main technical challenges of rectennas and WPT transmitters are discussed. Furthermore, this paper presents the recent advances on the development of these technologies, including the possibility of powering RFID systems through the millimeter wave power from 5G networks, the trends in flexible rectennas design and the technological developments on the simultaneous wireless information and power transfer (SWIPT).

14 May 2019 in IEEE Transactions on Microwave Theory and Techniques
Verified
Journal Article
Closed access
DBDaniel Belo
Daniel Belo
DRDiogo C. Ribeiro
Diogo C. Ribeiro
Pedro PinhoPedro Pinho
Pedro Pinho
Nuno CarvalhoNuno Carvalho
Nuno Carvalho
This paper proposes a selective, tracking, and power adaptive far-field wireless power transfer (WPT) system that may be integrated into passive wireless sensor networks (PWSNs). Both transmitter and receiving nodes are developed with features that allow them to cooperate. The system operates based on a backscattered pilot signal, which is used to control and focus the radiated energy. The transmitter may change between several states by turning on or off sets of antenna elements. Each of these states will transmit and consume a specific amount of power, and they will be selected based on the node's received signal strength (RSS). The receiving nodes are low complexity and battery-less devices, which use a small portion of the rectified energy to create an RSS-dependent modulation frequency, used to drive a backscatter modulator. Based on the nonlinear response of the rectifying devices, additional hardware was integrated into the nodes to activate/wake up them from specific wireless power signals. A complete system operating at 5.8 GHz for WPT and 3.6 GHz for the pilot signal is reported. It will be shown that effective far-field WPT links can be created with reasonable simplicity.

8 October 2019 in IEEE Transactions on Microwave Theory and Techniques
Verified
Journal Article
Closed access
DBDaniel Belo
Daniel Belo
RCRicardo Correia
Ricardo Correia
YDYuan Ding
Yuan Ding
SDSpyridon Nektarios Daskalakis
Spyridon Nektarios Daskalakis
GGGeorge Goussetis
George Goussetis
Nuno CarvalhoNuno Carvalho
Nuno Carvalho
This article describes the design of an IQ impedance modulator radio front-end which is used to generate long range (LoRa) symbols with backscattering techniques, allowing building low-power devices that may be compatible with the current LoRa networks. It is shown that a linear frequency modulated (LFM) chirp can be generated by properly varying the phase of a reflected wave instead of directly varying its instantaneous frequency. The proposed device consists of two radio frequency (RF) transistors that generate a set of impedances by changing their gate bias, allowing reflecting their incident wave with predefined phase values. By joining these two reflected waves in quadrature, a new set of impedances is obtained whose phases vary 360°, on a constant Voltage Standing Wave Ratio (VSWR) circle. In order to validate the proposed design, several LoRa symbols were generated and successfully transmitted and decoded. Measurements of the bit error rate (BER) versus signal-to-noise ratio (SNR) were conducted and shown to be in accordance with other related work. Moreover, the impact of intentional perturbations added to the control bias voltages was analyzed and tests over-the-air (OTA) were performed for different indoor propagation scenarios.

10 December 2020 in IEEE Transactions on Microwave Theory and Techniques
Verified
Journal Article
Closed access
DBDaniel Belo
Daniel Belo
Nuno CarvalhoNuno Carvalho
Nuno Carvalho
In this work, a general-purpose wireless energy receiving unit with improved backscatter (BS) communications capabilities assisted by far-field wireless power transfer (WPT) techniques is proposed. The unit employs an auxiliary RF-to-dc converter circuit which is used to simultaneously power and tune a low-power voltage controlled oscillator (VCO). By doing so, a relation between its frequency of oscillation and the instantaneous available RF input power is established. It is shown that by adding a small amplitude modulation to the wireless power carrier, the device can generate a linear frequency modulated signal which is used to provide low-power and long-range ON-OFF keying (OOK) chirp spread spectrum (CSS) BS communications. Experimental validation in real scenarios is provided, showing its superiority against the well-known conventional BS amplitude shift-keying (ASK) modulation scheme. Moreover, contrary to other designs, it is demonstrated that the proposed design does not need a dedicated processing unit to generate the required baseband signals, allowing to save power and complexity.

4 November 2020 in IEEE Transactions on Microwave Theory and Techniques
Verified
Journal Article
Closed access
MJMarina Jordao
Marina Jordao
DBDaniel Belo
Daniel Belo
Rafael F. S. CaldeirinhaRafael F. S. Caldeirinha
Rafael F. S. Caldeirinha
Arnaldo S. R. OliveiraArnaldo S. R. Oliveira
Arnaldo S. R. Oliveira
Nuno CarvalhoNuno Carvalho
Nuno Carvalho
A novel over-the-air (OTA) beamforming calibration procedure is proposed, which can be applied to different types of multiple-input multiple-output (MIMO) transmitting antennas. The method consists of using two tones on each antenna element, the main tone, and the tickle tone. The latter one operates in a different frequency for each antenna element and is used to obtain the optimum phase that needs to be set for each element to generate a beam in the desired direction, at the main tone frequency. The novel method was applied to linear, planar, 3-D antennas, and noncollocated multiantennas to validate its applicability to different antenna types. Line-of-Sight (LOS) and non-LOS experimental results demonstrate that the method can be used to retrieve the required phase to fully control the antenna radiation pattern. An optimum radiation pattern and lowest error vector magnitude (EVM) can be achieved even under high multipath effects/non-LOS conditions. A comparison between the performance and the application of the array factor (AF) theory is presented for practical indoor scenarios, demonstrating the effectiveness of the method. It is demonstrated that the method may be an alternative to the calibration of nonstandard MIMO antennas, where the AF computation is complex or not possible.

9 May 2022 in Energies
Verified
Journal Article
Open access
PDF file
DMDiogo Matos
Diogo Matos
Ricardo A. M. PereiraRicardo A. M. Pereira
Ricardo A. M. Pereira
HRHelena Ribeiro
Helena Ribeiro
BMBernardo Mendes
Bernardo Mendes
DBDaniel Belo
Daniel Belo
Nuno CarvalhoNuno Carvalho
Nuno Carvalho
Wireless power transfer promises to revolutionize the way in which we use and power mobile devices. However, low transfer efficiencies prevent this technology from seeing wide scale real-world adoption. The aim of this work is to use quasioptics to develop a system composed of a dielectric lens fed by a phased array to reduce spillover losses, increasing the beam efficiency, while working on the antenna system’s Fresnel zone. The DC-RF electronics, digital beamforming and beam-steering by an FPGA, and radiating 4 × 4 microstrip patch phased array have been developed and experimented upon, while the lens has been designed and simulated. This paper details these preliminary results, where the phased array radiation pattern was measured, showing that the beam is being generated and steered as expected, prompting the lens construction for the complete system experimentation.