1 January 2007 in Journal of Glaciology
To avoid some of the limitations of studying soft-bed processes through boreholes, a prism of simulated till (1.8 m × 1.6 m × 0.45 m) with extensive instrumentation was constructed in a trough blasted in the rock bed of Engabreen, a temperate glacier in Norway. Tunnels there provide access to the bed beneath 213 m of ice. Pore-water pressure was regulated in the prism by pumping water to it. During experiments lasting 7–12 days, the glacier regelated downward into the prism to depths of 50–80 mm, accreting ice-infiltrated till at rates predicted by theory. During periods of sustained high pore-water pressure (70–100% of overburden), ice commonly slipped over the prism, due to a water layer at the prism surface. Deformation of the prism was activated when this layer thinned to a sub-millimeter thickness. Shear strain in the till was pervasive and decreased with depth. A model of slip by ploughing of ice-infiltrated till across the prism surface accounts for the slip that occurred when effective pressure was sufficiently low or high. Slip at low effective pressures resulted from water-layer thickening that increased non-linearly with decreasing effective pressure. If sufficiently widespread, such slip over soft glacier beds, which involves no viscous deformation resistance, may instigate abrupt increases in glacier velocity.
15 July 2021 in Frontiers in Earth Science
Ice at depth in ice-stream shear margins is thought to commonly be temperate, with interstitial meltwater that softens ice. Models that include this softening extrapolate results of a single experimental study in which ice effective viscosity decreased by a factor of ∼3 over water contents of ∼0.01–0.8%. Modeling indicates this softening by water localizes strain in shear margins and through shear heating increases meltwater at the bed, enhancing basal slip. To extend data to higher water contents, we shear lab-made ice in confined compression with a large ring-shear device. Ice rings with initial mean grain sizes of 2–4 mm are kept at the pressure-melting temperature and sheared at controlled rates with peak stresses of ∼0.06–0.20 MPa, spanning most of the estimated shear-stress range in West Antarctic shear margins. Final mean grain sizes are 8–13 mm. Water content is measured by inducing a freezing front at the ice-ring edges, tracking its movement inward with thermistors, and fitting the data with solutions of the relevant Stefan problem. Results indicate two creep regimes, below and above a water content of ∼0.6%. Comparison of effective viscosity values in secondary creep with those of tertiary creep from the earlier experimental study indicate that for water contents of 0.2–0.6%, viscosity in secondary creep is about twice as sensitive to water content than for ice sheared to tertiary creep. Above water contents of 0.6%, viscosity values in secondary creep are within 25% of those of tertiary creep, suggesting a stress-limiting mechanism at water contents greater than 0.6% that is insensitive to ice fabric development in tertiary creep. At water contents of ∼0.6–1.7%, effective viscosity is independent of water content, and ice is nearly linear-viscous. Minimization of intercrystalline stress heterogeneity by grain-scale melting and refreezing at rates that approach an upper bound as grain-boundary water films thicken might account for the two regimes.
12 November 2018 in Journal of Geophysical Research: Earth Surface
The subglacial processes of abrasion and quarrying are thought to be primarily responsible for bedrock erosion by glaciers. While theory points to sliding speed as the dominant control on abrasion, rates of quarrying are likely scaled by a more complex combination of sliding speed, effective pressure, bed roughness, and short‐term water‐pressure fluctuations. Here we pair a model for quarrying based on statistical characterization of bedrock strength with a model for subglacial hydrology that describes the temporal evolution of cavities under the influence of variations in sliding speed and effective pressure. Using a finite element model, we simulate the evolution of the hydrological system at the base of a glacier and compute rates of abrasion and quarrying. Cavity lengths and channel cross sections evolve through time, causing temporal shifts in ice‐bed contact area, which in turn govern the differential stress that influences erosion over the course of a year. Our results demonstrate how variations in meltwater production amplify rates of subglacial erosion relative to the case of steady meltwater generation. The level of amplification depends on how the variations control the ice‐bed contact area. Seasonal variations are most effective in boosting mean rates of basal sliding and hence subglacial abrasion, whereas shorter‐term variations (monthly‐weekly) most strongly influence rates of subglacial quarrying through temporal amplification of differential bedrock stress around cavities. This influence of transient hydrology on subglacial erosion processes may explain why glaciers in temperate climates with strong variations in temperature and precipitation erode faster than similar‐type glaciers in polar environments.
21 July 2004 in Earth Surface Processes and Landforms