4 February 2021 in Superconductor Science and Technology
Fiber-optic thermometry has the potential to provide rapid and reliable quench detection for emerging large-scale, high-field superconducting magnets fabricated with high-temperature-superconductor (HTS) cables. Developing non-voltage-based quench detection schemes, such as fiber Bragg grating (FBG) technology, are particularly important for applications such as magnetic fusion devices where a high degree of induced electromagnetic noise impose significant challenges on traditional voltage-based quench detection methods. To this end, two fiber optic quench detection techniques—FBG and ultra-long FBG (ULFBG)—were incorporated into two vacuum pressure impregnated, insulated, partially transposed, extruded, and roll-formed (VIPER) high-current HTS cables and tested in the SULTAN facility, which provides high-fidelity operating conditions to large-scale superconducting magnets. During surface heater induced quench-like events under a variety of operating conditions, FBG and ULFBG demonstrated strong signal-to-noise ratios (SNRs) ranging from 4 to 32 and measured single-digit temperature excursions; both the SNR and temperature sensitivity increase with temperature. Fiber thermal response times ranged between effectively instantaneous to a few seconds depending on the operating temperature. Strain sensitivity dominates the thermal sensitivity in the conditions achievable at SULTAN; however, measurements at higher quench evolution temperatures, coupled to future work to increase the thermal-to-strain signal, show promise for quench detection capability in full-scale magnets where temperature and strain may occur simultaneously. Overall, FBG and ULFBG were proven capable to quickly and reliably detect small temperature disturbances which induced quench initiation events for high current VIPER HTS conductors in realistic operating conditions, motivating further work to develop FBG and ULFGB quench detection systems for full-scale HTS magnets.
4 October 2024 in Superconductor Science and Technology
A low-AC loss Rare-earth barium copper oxide (REBCO) cable, based on the VIPER cable technology has been developed by commonwealth fusion systems for use in high-field, compact tokamaks. The new cable is composed of partitioned and transposed copper ‘petals’ shaped to fit together in a circular pattern with each petal containing a REBCO tape stack and insulated from each other to reduce AC losses. A stainless-steel jacket adds mechanical robustness—also serving as a vessel for solder impregnation—while a tube runs through the middle for cooling purposes. Additionally, fiber optic sensors are placed under the tape stacks for quench detection (QD). To qualify this design, a series of experiments were conducted as part of the SPARC tokamak central solenoid (CS) model coil program—to retire the risks associated with full-scale, fast-ramping, high-flux high temperature superconductors CS and poloidal field coils for tokamak fusion power plants and net-energy demonstrators. These risk-study and risk-reduction experiments include (1) AC loss measurement and model validation in the range of ∼5 T s−1, (2) an IxB electromagnetic (EM) loading of over 850 kN m−1 at the cable level and up to 300 kN m−1 at the stack level, (3) a transverse compression resilience of over 350 MPa, (4) manufacturability at tokamak-relevant speeds and scales, (5) cable-to-cable joint performance, (6) fiber optic-based QD speed, accuracy, and feasibility, and (7) overall winding pack integration and magnet assembly. The result is a cable technology, now referred to as PIT VIPER, with AC losses that measure fifteen times lower (at ∼5 T s−1) than its predecessor technology; a 2% or lower degradation of critical current (Ic
) at high IxB EM loads; no detectable Ic
degradation up to 600 MPa of transverse compression on the cable unit cell; end-to-end magnet manufacturing, consistently producing Ic
values within 7% of the model prediction; cable-to-cable joint resistances at 20 K on the order of ∼15 nΩ; and fast, functional QD capabilities that do not involve voltage taps.
26 September 2022 in Applied Optics
Optical fiber Bragg gratings (FBGs) are well suited for applications as temperature or/and strain sensors in harsh environments, e.g., detecting thermal hot spots in high-temperature superconductor (HTS) fusion energy magnets at cryogenic temperatures and high radiation environments. To maximize the signal-to-noise ratio (SNR) of the FBGs to a hot spot, we propose to have them mounted in V-shaped grooves of HTS’ copper former. To investigate the differences between different adhesives on transferring strain and heat in this configuration, five arrays of FBGs are mounted in the V-shaped grooves of a copper dog-bone using Scotch-Weld epoxy, Stycast 2850 FT, Apiezon N, and Loctite 5145 silicone. The copper is cycled through tensile forces in a modified universal tensile tester, subjected to a thermal cycle between 293 K and 77 K, and exposed to heat pulse propagations at 293 K and 80 K. The FBGs that are bonded using Stycast show the highest temperature and strain sensitivities at room and cryogenic temperatures. No major differences in the temperature and strain sensitivities have been found between Ormocer and polyimide coated FBGs. Apiezon N is found to transfer strain consistently well below 245 K, which is comparable with other bonding materials in the temperature range between 77 K and 110 K. The FBGs bonded with the four adhesives in the V-groove configurations are shown to have comparable SNRs to a temperature rise of 20 K at 80 K. This paper emphasizes the importance of maximizing the thermal strain transferred from the host material through the bonding agents to achieve high temperature sensitivity of FBGs.