Bori Mokrickiy

Bori Mokrickiy

Auto-generated profile, based on publicly available information

Bori Mokrickiy

Komsomolsk-on-Amur State University, Komsomolsk-on-Amur, Russia

Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
10 November 2018 in Coatings
Verified
Journal Article
Open access
PDF file
Alexey VereschakaAlexey Vereschaka
Alexey Vereschaka
MOMaksim Oganyan
Maksim Oganyan
YBYuri Bublikov
Yuri Bublikov
NSNikolay Sitnikov
Nikolay Sitnikov
KDKonstantin Deev
Konstantin Deev
BMBoris Mokritskii
Boris Mokritskii
The study deals with an increase in the tool life parameter for metal-cutting tools and efficiency of end milling for titanium alloys, due to the use of tools with multilayered composite nano-structured Zr–ZrN–(Zr,Al)N and Zr–ZrN–(Zr,Cr,Al)N coatings, deposited through the technology of the filtered cathodic vacuum arc deposition (FCVAD). The studies included the microstructured investigations using SEM, the analysis of chemical composition (Energy-dispersive X-ray spectroscopy, EDXS), the determination of the value of critical failure force (with the use of scratch testing), and the measurement of the microhardness of the coatings under study. The cutting tests were conducted in end milling of titanium alloys at various cutting speeds. The mechanisms of wear and failure for end milling cutters with the coatings under study were studied in milling. The studies determined the advantages of using a tool with the coatings under study compared to an uncoated tool, as well as to tools with the commercial Ti–TiN coating and the nano-structured Ti–TiN–(Ti,Al)N coating. Adding Cr to the composition of the coating can significantly increase the hardness, while the coating retains sufficient ductility and brittle fracture resistance, which allows for a best result when milling titanium alloys.

1 February 2013 in Russian Engineering Research
Verified
Journal Article
Closed access
PDF file
BMB. Ya. Mokritskii
B. Ya. Mokritskii
AKA. V. Kirichek
A. V. Kirichek
ASA. M. Shpilev
A. M. Shpilev
DPD. A. Pustovalov
D. A. Pustovalov
PSP. A. Sablin
P. A. Sablin
Pendulum inscription by means of an indenter, with acoustic recording, may be employed to analyze the failure kinetics of tool materials and predict tool quality. The use of acoustic emission to assess tool failure is well known. Its downside is that the load introduced by the indenter is local. A possible compensation is to inscribe the indenter in the surface at constant depth. Pendulum inscription permits investigation of the failure kinetics when the indenter travels over an arc within the sample [1–3].

25 January 2014 in Chemical and Petroleum Engineering
Verified
Journal Article
Closed access
PDF file
BMB. Ya. Mokritskii
B. Ya. Mokritskii

21 May 2018
Verified
Conference Paper
Open access
PDF file
AMAnna Morozova
Anna Morozova
BMBoris Mokritskii
Boris Mokritskii
VVVladislav Vereshchagin
Vladislav Vereshchagin
A continuous change of physical and mechanical characteristics and operational properties of functional and structural materials demands a corresponding adjustment of the cutting tool material for machining. The adjustment involves the development of a new tool material and sometimes a new design tool. These two directions of the improvement of metal-cutting tools have a lot of solutions. A look through these options by trial and error is expensive and laborious. Of course, that there are accepted trends in the choice of a rational variant, but they are not justified scientifically and are associated with the experience of the developer. In this situation, it is desirable to simulate the processing of the workpiece with a tool to identify the most preferred solutions for the design and material of the tool. The possibility of using the ANSYS software environment (standard module Workbench Explicit Dynamics) for such a choice of the preferred variants of the design and material of the tool is considered.

6 August 2023 in Computational nanotechnology
Verified
Journal Article
Closed access
BMBoris Ya. Mokritski
Boris Ya. Mokritski
VZVictor G. Zavodinsky
Victor G. Zavodinsky
OGOlga A. Gorkusha
Olga A. Gorkusha
The energy of a three-layer coating on the surface of a hard alloy based on tungsten carbide WC92Co8 (technical name VK8) has been studied using computer simulation methods of density functional theory and pseudopotentials. The first layer is titanium; the second layer is titanium nitride; the third layer is a composite nitride (Ti, Cr, Al)N. The dependence of the energy of adhesion of titanium to the WC and Co surfaces on the thickness of the deposited titanium layer (from one to three atomic layers) has been studied. The adhesion energy of titanium nitride to the pre-deposited titanium layer is calculated. For four variants of the structure of the compound (Ti, Cr, Al)N, the adhesion energy of this compound to the TiN surface was calculated.

12 April 2023 in Transport engineering
Verified
Journal Article
Closed access
BMBori Mokrickiy
Bori Mokrickiy
AKAlexander Kosmynin
Alexander Kosmynin
PSPavel Sablin
Pavel Sablin
VSVadim Shelkovnikov
Vadim Shelkovnikov
The study objective is to increase the durability period of replaceable carbide inserts by applying coatings for turning hard-to-machine stainless steels. Research results: recommendations are made on the choice of a rational coating of a metal-cutting tool, depending on its operating conditions. Conclusions: The developed coatings allow to increase the durability period of the cutting tool up to 3 times. The paper discusses the results of applying the newly developed coatings on the hard-alloy material of VK8 brand. The analysis is done for turning stainless steels of 09X17N7YU, 12X18N10T, 13X15N5AM-3 grades. The most rational coatings are found, which make it possible to increase the durability period of the metal-cutting tool up to 3 times.