7 December 2018 in Energy & Environmental Science
All inorganic perovskite solar cells lead to extended device lifespan in an accelerated ageing test.
14 December 2018 in Advanced Energy Materials
5 May 2020 in ACS Energy Letters
MAMahmoud Hussein Aldamasy
+4
22 September 2023 in ACS Energy Letters
EGEmilio Gutierrez-Partida
+9
In perovskite solar cells (PSCs) energy level alignment and charge extraction at the interfaces are the essential factors directly affecting the device performance. In this work, we present a modified interface between all-inorganic CsPbI3 perovskite and its hole-selective contact (spiro-OMeTAD), realized by the dipole molecule trioctylphosphine oxide (TOPO), to align the energy levels. On a passivated perovskite film, with n-octylammonium iodide (OAI), we created an upward surface band-bending at the interface by TOPO treatment. This improved interface by the dipole molecule induces a better energy level alignment and enhances the charge extraction of holes from the perovskite layer to the hole transport material. Consequently, a Voc of 1.2 V and a high-power conversion efficiency (PCE) of over 19% were achieved for inorganic CsPbI3 perovskite solar cells. Further, to demonstrate the effect of the TOPO dipole molecule, we present a layer-by-layer charge extraction study by a transient surface photovoltage (trSPV) technique accomplished by a charge transport simulation.
21 June 2019 in Energy & Environmental Science
Direct piezoelectric force microscopy (DPFM) is employed to examine whether or not lead halide perovskites exhibit ferroelectricity. Compared to conventional piezoelectric force microscopy, DPFM is a novel technique capable of measuring piezoelectricity directly. This fact is fundamental to be able to examine the existence of ferroelectricity in lead halide perovskites, an issue that has been under debate for several years. DPFM is used to detect the current signals, i.e. changes in the charge distribution under the influence of the scan direction and applied force of the atomic force microscope (AFM) tip in contact mode. For comparison, (i) we use DPFM on lead halide perovskites and well-known ferroelectric materials (i.e. periodically poled lithium niobate and lead zirconate titanate); and (ii) we conduct parallel experiments on MAPbI3 films of different grain sizes, film thicknesses, substrates, and textures using DPFM as well as piezoelectric force microscopy (PFM) and electrostatic force microscopy (EFM). In contrast to previous work that claimed there were ferroelectric domains in MAPbI3 perovskite films, our work shows that the studied perovskite films Cs0.05(FA0.83MA0.17)0.95Pb(I0.83Br0.17)3 and MAPbI3 are ferroelectricity-free. The observed current profiles of lead halide perovskites possibly originate from ion migration that happens under an applied electrical bias and in strained samples under mechanical stress. This work provides a deeper understanding of the fundamental physical properties of the organic–inorganic lead halide perovskites and solves a longstanding dispute about their non-ferroelectric character: an issue of high relevance for optoelectronic and photovoltaic applications.
24 June 2019 in Advanced Energy Materials
Two new hole selective materials (HSMs) based on dangling methylsulfanyl groups connected to the C‐9 position of the fluorene core are synthesized and applied in perovskite solar cells. Being structurally similar to a half of Spiro‐OMeTAD molecule, these HSMs (referred as FS and DFS) share similar redox potentials but are endowed with slightly higher hole mobility, due to the planarity and large extension of their structure. Competitive power conversion efficiency (up to 18.6%) is achieved by using the new HSMs in suitable perovskite solar cells. Time‐resolved photoluminescence decay measurements and electrochemical impedance spectroscopy show more efficient charge extraction at the HSM/perovskite interface with respect to Spiro‐OMeTAD, which is reflected in higher photocurrents exhibited by DFS/FS‐integrated perovskite solar cells. Density functional theory simulations reveal that the interactions of methylammonium with methylsulfanyl groups in DFS/FS strengthen their electrostatic attraction with the perovskite surface, providing an additional path for hole extraction compared to the sole presence of methoxy groups in Spiro‐OMeTAD. Importantly, the low‐cost synthesis of FS makes it significantly attractive for the future commercialization of perovskite solar cells.