Zafar Iqbal

Zafar Iqbal

Auto-generated profile, based on publicly available information

Zafar Iqbal

Helmholtz‐Zentrum Berlin für Materialien und Energie GmbH Berlin Germany

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
22 September 2023 in ACS Energy Letters
Verified
Journal Article
Open access
ZIZafar Iqbal
Zafar Iqbal
FZFengshuo Zu
Fengshuo Zu
AMArtem Musiienko
Artem Musiienko
EGEmilio Gutierrez-Partida
Emilio Gutierrez-Partida
HKHans Köbler
Hans Köbler
QWQiong Wang
Qiong Wang
In perovskite solar cells (PSCs) energy level alignment and charge extraction at the interfaces are the essential factors directly affecting the device performance. In this work, we present a modified interface between all-inorganic CsPbI3 perovskite and its hole-selective contact (spiro-OMeTAD), realized by the dipole molecule trioctylphosphine oxide (TOPO), to align the energy levels. On a passivated perovskite film, with n-octylammonium iodide (OAI), we created an upward surface band-bending at the interface by TOPO treatment. This improved interface by the dipole molecule induces a better energy level alignment and enhances the charge extraction of holes from the perovskite layer to the hole transport material. Consequently, a Voc of 1.2 V and a high-power conversion efficiency (PCE) of over 19% were achieved for inorganic CsPbI3 perovskite solar cells. Further, to demonstrate the effect of the TOPO dipole molecule, we present a layer-by-layer charge extraction study by a transient surface photovoltage (trSPV) technique accomplished by a charge transport simulation.

9 February 2024 in Journal of the American Chemical Society
Verified
Journal Article
Open access
ZIZafar Iqbal
Zafar Iqbal
RFRoberto Félix
Roberto Félix
AMArtem Musiienko
Artem Musiienko
JTJarla Thiesbrummel
Jarla Thiesbrummel
HKHans Köbler
Hans Köbler
QWQiong Wang
Qiong Wang
Here, we report a detailed surface analysis of dry- and ambient air-annealed CsPbI3 films and their subsequent modified interfaces in perovskite solar cells. We revealed that annealing in ambient air does not adversely affect the optoelectronic properties of the semiconducting film; instead, ambient air-annealed samples undergo a surface modification, causing an enhancement of band bending, as determined by hard X-ray photoelectron spectroscopy measurements. We observe interface charge carrier dynamics changes, improving the charge carrier extraction in CsPbI3 perovskite solar cells. Optical spectroscopic measurements show that trap state density is decreased due to ambient air annealing. As a result, air-annealed CsPbI3-based n-i-p structure devices achieved a 19.8% power conversion efficiency with a 1.23 V open circuit voltage.

14 July 2025 in ACS Energy Letters
Verified
Journal Article
Open access
DPDebendra Prasad Panda
Debendra Prasad Panda
RIRabeb Issaoui
Rabeb Issaoui
ZIZafar Iqbal
Zafar Iqbal
GGGopal Krishna Murthy Grandhi
Gopal Krishna Murthy Grandhi
Muhammad Okash Ur RehmanMuhammad Okash Ur Rehman
Muhammad Okash Ur Rehman
AAAntonio Abate
Antonio Abate
Indoor photovoltaic (IPV) technology has emerged as an effective strategy to sustainably power batteryless Internet of Things (IoT) devices. Though tin perovskite solar cells offer competitive IPV performance, their effectiveness is often compromised by Sn2+ oxidation, particularly when processed with dimethyl sulfoxide (DMSO) solvent. This work explored the IPV performance of DMSO-free tin perovskites FASnI3–x Br x by tuning the halide composition. Notably, X-ray photoelectron spectroscopy confirms no traces of Sn4+, highlighting the critical role of eliminating DMSO. Under 1000 lx indoor illumination, the power conversion efficiency (PCE) increases with Br content, reaching a maximum of 11.1% for FASnI2Br without introducing any reducing agent. Remarkably, after six months of storage, it exhibited an impressive indoor PCE of 11.9%, demonstrating the effectiveness of the DMSO-free processing route for the intrinsic stability of the tin perovskite. These findings provide crucial insights for developing high-performance, lead-free perovskite materials for sustainable energy applications and IoT devices.

6 May 2025 in Small Science
Verified
Journal Article
Open access
TGThomas W. Gries
Thomas W. Gries
DRDavide Regaldo
Davide Regaldo
HKHans Köbler
Hans Köbler
NHNoor Titan Putri Hartono
Noor Titan Putri Hartono
SHSteven Harvey
Steven Harvey
AAAntonio Abate
Antonio Abate
Inorganic perovskite CsPbI3 solar cells hold great potential for improving the operational stability of perovskite photovoltaics. However, electron extraction is limited by the low conductivity of TiO2, representing a bottleneck for achieving stable performance. In this study, a co‐doping strategy for TiO2 using Nb(V) and Sn(IV), which reduces the material's work function by 80 meV compared to Nb(V) mono‐doped TiO2, is introduced. To gain fundamental understanding of the processes at the interfaces between the perovskite and charge‐selective layer, transient surface photovoltage measurements are applied, revealing the beneficial effect of the energetic and structural modification on electron extraction across the CsPbI3/TiO2 interface. Using 2D drift‐diffusion simulations, it is found that co‐doping reduces the interface hole recombination velocity by two orders of magnitude, increasing the concentration of extracted electrons by 20%. When integrated into n–i–p solar cells, co‐doped TiO2 enhances the projected TS80 lifetimes under continuous AM1.5G illumination by a factor of 25 compared to mono‐doped TiO2. This study provides fundamental insights into interfacial charge extraction and its correlation with operational stability of perovskite solar cells, offering potential applications for other charge‐selective contacts.

14 June 2024 in Solar RRL
Verified
Journal Article
Open access
ZIZafar Iqbal
Zafar Iqbal
TGThomas W. Gries
Thomas W. Gries
AMArtem Musiienko
Artem Musiienko
AAAntonio Abate
Antonio Abate
The efficient functioning of perovskite solar cells largely depends on the interaction between perovskite halide materials and the hole‐transport layer poly(3‐hexylthiophene) (P3HT). However, a high rate of nonradiative recombination often hampers this interaction, leading to poor performance of the solar cells. We have developed a technique to modify the interface using a long‐chain alkyl halide molecule called n‐hexyl trimethylammonium bromide to address this issue. This modification technique significantly improves hole extraction, leading to an impressive open‐circuit voltage of 1.14 V and a power conversion efficiency of 15.8% for inorganic perovskite CsPbI3 with P3HT as a dopant‐free hole‐transport layer. This breakthrough can pave the way for developing more efficient and sustainable solar cells.

20 May 2026 in Small
Verified
Journal Article
Open access
PDF file
MAMahmoud H. Aldamasy
Mahmoud H. Aldamasy
AMArtem Musiienko
Artem Musiienko
MRMarin Rusu
Marin Rusu
DRDavide Regaldo
Davide Regaldo
ZIZafar Iqbal
Zafar Iqbal
AAAntonio Abate
Antonio Abate
Tin perovskites are emerging as a sustainable alternative to lead‐based photovoltaics, yet their efficiency remains limited by energy‐level mismatch and intrinsic instability from tin oxidation. Progress is further hindered by inconsistent electrical behavior, obscuring the true bottlenecks of device performance. Here, we deliver a comprehensive, layer‐resolved analysis of FASnI 3 solar cells, combining Kelvin probe and photoelectron yield spectroscopy to directly map the band structure and quantify interfacial losses. We reveal that the commonly overlooked Bathocuproine buffer layer plays a decisive role in boosting open‐circuit voltage by forming a hybrid energy level with silver, enabling efficient electron extraction.Using time‐resolved surface photovoltage, we uncover the ultrafast charge‐transfer dynamics governing device operation. These insights expose a critical limitation in the conventional p‐p‐n, where severe recombination at the perovskite and hole transport interface suppresses performance. A transition to an n‐p‐p configuration significantly enhances charge extraction and minimizes recombination losses.By integrating these findings into a predictive digital twin, we establish a clear, experimentally validated roadmap toward tin perovskite solar cells exceeding 25% efficiency. This work provides both fundamental understanding and actionable design rules, accelerating the development of high‐performance, lead‐free photovoltaics.