Preoperative assessment of tissue anatomy and accurate surgical planning is crucial in conjoined twin separation surgery. We developed a new method that combines three-dimensional (3D) printing, assembling, and casting to produce anatomic models of high fidelity for surgical planning. The related anatomic features of the conjoined twins were captured by computed tomography (CT), classified as five organ groups, and reconstructed as five computer models. Among these organ groups, the skeleton was produced by fused deposition modeling (FDM) using acrylonitrile-butadiene-styrene. For the other four organ groups, shell molds were prepared by FDM and cast with silica gel to simulate soft tissues, with contrast enhancement pigments added to simulate different CT and visual contrasts. The produced models were assembled, positioned firmly within a 3D printed shell mold simulating the skin boundary, and cast with transparent silica gel. The produced phantom was subject to further CT scan in comparison with that of the patient data for fidelity evaluation. Further data analysis showed that the produced model reassembled the geometric features of the original CT data with an overall mean deviation of less than 2 mm, indicating the clinical potential to use this method for surgical planning in conjoined twin separation surgery.
Fine particles about 20 nm in average diameter of alloys prepared by evaporation in nitrogen atmosphere were studied using Mössbauer technique, x-ray diffraction, and magnetic measurement. Their different phases were identified, and their hyperfine field distribution, specific saturation magnetization, remnant magnetization, and coercivity were determined. The fine particles show some properties, which are sensitive to the Ni content x and different from those of corresponding bulk alloys. The results suggest that the fine particles may be useful from an applied viewpoint.
1 February 2013 in Radiation Effects and Defects in Solids
Bi 3.15Nd 0.85Ti 3O 12 (BNT) thin films have been deposited onto Pt/Ti/SiO 2/Si substrates by chemical solution deposition. Pt top electrodes were then deposited to form the capacitor structure (Pt/BNT/Pt). The prepared capacitors were subjected to 1×1015 n/ cm2 neutron radiation. Loss in the remanent polarization and changes in the leakage current characteristics were observed after radiation. Possible mechanisms concerning the radiation-induced changes were discussed. The increased pinning of domain wall was identified as the primary reason for polarization loss, while the decreased barrier height resulted in the increased leakage current.
Adsorption of chalcogen atoms on metal surfaces has attracted increasing interest for both the fundamental research and industrial applications. Here, we report a systematic study of selenium (Se) adsorption on Au(111) at varies substrate temperatures by scanning tunneling microscopy. At room temperature, small Se clusters are randomly dispersed on the surface. Increasing the temperature up to 200 °C, a well-ordered lattice of Se molecules consisting of 8 Se atoms in ring-like structure is formed. Further increasing the temperature to 250 °C gives rise to the formation of Se monolayer with Au(111)- lattices superimposed with a quasi-hexagonal lattice. Desorption of Se atoms rather than the reaction between the Se atoms and the Au substrate occurs if further increasing the temperature. The ordered structures of selenium monolayers could serve as templates for self-assemblies and our findings in this work might provide insightful guild for the epitaxial growth of the two-dimensional transition metal dichalcogenides.
18 January 2011 in Journal of the American Ceramic Society
The device physics of AlGaN/GaN metal-oxide-semiconductor high-electron mobility transistor (MOS-HEMT) with localized stress introduced by a diamond-like carbon (DLC) liner or encapsulation layer was investigated. DLC film with high intrinsic compressive stress formed over AlGaN/GaN MOS-HEMTs contributed local compressive stress in the channel region. This was found to reduce the two-dimensional electron gas (2-DEG) density in the channel, leading to a positive threshold voltage shift. Transconductance and drain current at a given gate overdrive were also improved. On the other hand, the DLC introduced local tensile stress in the region between the gate and source/drain contacts, leading to a localized increase in 2-DEG density, giving reduced series resistance. The results of this work are expected to be useful for strain engineering of AlGaN/GaN MOS-HEMTs.