Ji Hun Yu

Ji Hun Yu

Auto-generated profile, based on publicly available information

Ji Hun Yu

Department of Tractor R&D Center LS Mtron 55322 Wanju Korea

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
17 November 2022 in Advances in Mechanical Engineering
Verified
Journal Article
Open access
JYJi Hun Yu
Ji Hun Yu
PJPark Jinkam
Park Jinkam
SCSu Hwan Cheon
Su Hwan Cheon
SBSeojung Byeon
Seojung Byeon
JLJin Woong Lee
Jin Woong Lee
Agricultural tractors are connected with various implements such as plow, baler, rotovator, and loader for performing agricultural work. In particular, the rotovator is used to crush and uniformly spread the soil after plowing operations. However, achieving uniformly spread soil and flattened fields using rotovator can be extremely challenging, because the soil is often pushed to a particular side or remains on a slope owing to the variations in soil composition, plowing depth, and the skill level of workers, which consequently affects the transplantation work. This study aims to analyze the prediction accuracy of the implement and tractor attitudes as a reference standard by (a) developing an algorithm to predict the implement attitude based on the hitch height, support points of the lower link and lift rod, and distance between the lower links, through four-section link mathematical modeling for a three-point hitch system, and (b) using an observer to predict the tractor attitude using a Kalman filter with gyroscopic and acceleration sensors. We developed a control algorithm using the gyroscopic and acceleration information from the sensor to improve the precision and adjustment speed of the conventional tractor–implement leveling-control system. In addition, the performance improvement was verified by comparing the conventional and proposed systems. The results revealed that the error rates in the proposed system were up to 72% less than those of the conventional system, implying that the control performance of the stated system could be improved by reducing the implement attitude estimation error and tractor attitude measurement delay.

1 December 2025 in Korean Journal of Agricultural Science
Verified
Journal Article
Open access
PDF file
DKDong Wook Kim
Dong Wook Kim
JYJi Hun Yu
Ji Hun Yu
JPJong Dae Park
Jong Dae Park
MPMin Jong Park
Min Jong Park
YKYong-Joo Kim
Yong-Joo Kim
This study aimed to develop a simulation model and validate the durability of a 20-kW electric tractor power transmission. Power transmission consisted of a motor, transmission, axle and wheels. The transmission simulation model was developed using MASTA, a gear analysis software, and motor rotational speed, as well as wheel and power takeoff (PTO) torque generated during agricultural work were applied as input parameters of the simulation model. The safety factors of the gears and bearing damage were analyzed. The power transmission durability test was conducted using a dynamometer. The input motor speed was adjusted by the input speed, and the load motor torque was adjusted by applied the load under test conditions. Zero-failure test times were 2,418 hours, whereas acceleration life testing (ALT) was approximately 160 hours using the dynamometer. The gear safety analysis results showed that the bending safety factor of the pinion in spiral bevel gear was 1.19 and the contact safety factor was also 1.12 which was the lowest among all gear pairs. The bearing safety analysis showed that the highest bearing damage rate was 58.69%, and the lowest safety factor of 1.30. Gear and bearing analysis results of the powertrain satisfied the target safety. However, spalling was found in one tooth of the differential pinion gear. The face width of the damaged spiral bevel gear was changed from 41 to 43, and the safety factor was analyzed. The bending and contact safety factors were 1.71 and 1.32, respectively, which were improved by approximately 44% and 18%. It is judged that power transmission would be applied to electric tractors.

1 December 2025 in Korean Journal of Agricultural Science
Verified
Journal Article
Open access
PDF file
DKDong Wook Kim
Dong Wook Kim
JYJi Hun Yu
Ji Hun Yu
MPMin Jong Park
Min Jong Park
JPJong Dae Park
Jong Dae Park
YKYong-Joo Kim
Yong-Joo Kim
This study aimed to verify the agricultural working performance of an electric tractor by developing a 1-D power transmission system simulation model using SimulationX (ver. 4.4, ESI ITI GmbH, Germany). A load measurement system was installed on the electric tractor to measure real-time data during plow tillage, including axle torque and the state of charge (SOC) level of the battery. The t-tests were conducted to compare the measured and simulated axle torques and validated the simulation model. The p-values for the front and rear axles were 0.18 and 0.19, respectively, indicating no statistically significant differences. Although the measured and simulated SOC did not perfectly match, the trends showed similar patterns. The divergences in SOC were mainly due to the resolution limitations of the SOC sensor during measurement. Based on both measured and simulated results, the estimated workable time for plow tillage using the electric tractor was approximately 2 hours.