Space-charge-limited current (SCLC) measurements have been widely used to study the charge carrier mobility and trap density in semiconductors. However, their applicability to metal halide perovskites is not straightforward, due to the mixed ionic and electronic nature of these materials. Here, we discuss the pitfalls of SCLC for perovskite semiconductors, and especially the effect of mobile ions. We show, using drift-diffusion (DD) simulations, that the ions strongly affect the measurement and that the usual analysis and interpretation of SCLC need to be refined. We highlight that the trap density and mobility cannot be directly quantified using classical methods. We discuss the advantages of pulsed SCLC for obtaining reliable data with minimal influence of the ionic motion. We then show that fitting the pulsed SCLC with DD modeling is a reliable method for extracting mobility, trap, and ion densities simultaneously. As a proof of concept, we obtain a trap density of 1.3 × 1013 cm–3, an ion density of 1.1 × 1013 cm–3, and a mobility of 13 cm2 V–1 s–1 for a MAPbBr3 single crystal.
The short exciton diffusion length associated with most classical organic semiconductors used in organic photovoltaics (5-20 nm) imposes severe limits on the maximum size of the donor and acceptor domains within the photoactive layer of the cell. Identifying materials that are able to transport excitons over longer distances can help advancing our understanding and lead to solar cells with higher efficiency. Here, we measure the exciton diffusion length in a wide range of nonfullerene acceptor molecules using two different experimental techniques based on photocurrent and ultrafast spectroscopy measurements. The acceptors exhibit balanced ambipolar charge transport and surprisingly long exciton diffusion lengths in the range of 20 to 47 nm. With the aid of quantum-chemical calculations, we are able to rationalize the exciton dynamics and draw basic chemical design rules, particularly on the importance of the end-group substituent on the crystal packing of nonfullerene acceptors.
The presence of mobile ions in metal halide perovskites has been shown to adversely affect the intrinsic stability of perovskite solar cells (PSCs). However, the actual contribution of mobile ions to the total degradation loss compared with other factors such as trap-assisted recombination remains poorly understood. Here we reveal that mobile ion-induced internal field screening is the dominant factor in the degradation of PSCs under operational conditions. The increased field screening leads to a decrease in the steady-state efficiency, often owing to a large reduction in the current density. Instead, the efficiency at high scan speeds (>1,000 V s−1), where the ions are immobilized, is much less affected. We also show that the bulk and interface quality do not degrade upon ageing, yet the open-circuit voltage decreases owing to an increase in the mobile ion density. This work reveals the importance of ionic losses for intrinsic PSC degradation before chemical or extrinsic mechanical effects manifest.
Solution processed organic solar cells (OSCs) composed of all small molecules (ASM) are promising for production on an industrial scale owing to the properties of small molecules, such as well-defined chemical structures, high purity of materials, and outstanding repeatability from batch to batch synthesis. Remarkably, ASM OSCs with power conversion efficiency (PCE) beyond 13% were achieved by structure improvement of the electron donor and choosing Y6 as the electron acceptor. However, the fill factor (FF) is an obstacle that limits the further improvement of the PCE for these ASM OSCs. Herein, we focus on the FF improvement of recently reported ASM OSCs with BTR-Cl:Y6 as the active layer by miscibility-induced active layer morphology optimization. The incorporation of fullerene derivatives, which have good miscibility with both BTR-Cl and Y6, results in reduced bimolecular recombination and thus improved FF. In particular, when ca. 5 wt% of PC71BM was added in the active layer, a FF of 77.11% was achieved without sacrificing the open circuit voltage (VOC) and the short circuit current density (JSC), leading to a record PCE of 15.34% (certified at 14.7%) for ASM OSCs. We found that the optimized device showed comparable charge extraction, longer charge carrier lifetime, and slower bimolecular recombination rate compared with those of the control devices (w/o fullerene). Our results demonstrate that the miscibility driven regulation of active layer morphology by incorporation of a fullerene derivative delicately optimizes the active layer microstructures and improves the device performance, which brings vibrancy to OSC research.
Perovskite solar cells (PSCs) are one of the main research topics of the photovoltaic community; with efficiencies now reaching up to 24%, PSCs are on the way to catching up with classical inorganic solar cells. However, PSCs have not yet reached their full potential. In fact, their efficiency is still limited by nonradiative recombination, mainly via trap-states and by losses due to the poor transport properties of the commonly used transport layers (TLs). Indeed, state-of-the-art TLs (especially if organic) suffer from rather low mobilities, typically within 10–5 and 10–2 cm2 V–1 s–1, when compared to the high mobilities, 1–10 cm2 V–1 s–1, measured for perovskites. This work presents a comprehensive analysis of the effect of the mobility, thickness, and doping density of the transport layers based on combined experimental and modeling results of two sets of devices made of a solution-processed high-performing triple-cation (PCE ≈ 20%). The results are also cross-checked on vacuum-processed MAPbI3 devices. From this analysis, general guidelines on how to optimize a TL are introduced and especially a new and simple formula to easily calculate the amount of doping necessary to counterbalance the low mobility of the TLs.