26 February 2021 in ACS Energy Letters
Space-charge-limited current (SCLC) measurements have been widely used to study the charge carrier mobility and trap density in semiconductors. However, their applicability to metal halide perovskites is not straightforward, due to the mixed ionic and electronic nature of these materials. Here, we discuss the pitfalls of SCLC for perovskite semiconductors, and especially the effect of mobile ions. We show, using drift-diffusion (DD) simulations, that the ions strongly affect the measurement and that the usual analysis and interpretation of SCLC need to be refined. We highlight that the trap density and mobility cannot be directly quantified using classical methods. We discuss the advantages of pulsed SCLC for obtaining reliable data with minimal influence of the ionic motion. We then show that fitting the pulsed SCLC with DD modeling is a reliable method for extracting mobility, trap, and ion densities simultaneously. As a proof of concept, we obtain a trap density of 1.3 × 1013 cm–3, an ion density of 1.1 × 1013 cm–3, and a mobility of 13 cm2 V–1 s–1 for a MAPbBr3 single crystal.
3 January 2020 in ACS Energy Letters
9 May 2022 in ACS Energy Letters
As perovskite-based photovoltaics near commercialization, it is imperative to develop industrial-scale defect-passivation techniques. Vapor deposition is a solvent-free fabrication technique that is widely implemented in industry and can be used to fabricate metal-halide perovskite thin films. We demonstrate markably improved growth and optoelectronic properties for vapor-deposited [CH(NH2)2]0.83Cs0.17PbI3 perovskite solar cells by partially substituting PbI2 for PbCl2 as the inorganic precursor. We find the partial substitution of PbI2 for PbCl2 enhances photoluminescence lifetimes from 5.6 ns to over 100 ns, photoluminescence quantum yields by more than an order of magnitude, and charge-carrier mobility from 46 cm2/(V s) to 56 cm2/(V s). This results in improved solar-cell power conversion efficiency, from 16.4% to 19.3% for the devices employing perovskite films deposited with 20% substitution of PbI2 for PbCl2. Our method presents a scalable, dry, and solvent-free route to reducing nonradiative recombination centers and hence improving the performance of vapor-deposited metal-halide perovskite solar cells.
10 October 2019 in ACS Energy Letters
Perovskite halides are well-suited to monolithic multijunction photovoltaics, promising low cost solar-to-electrical power conversion. Critical to all-perovskite multijunction fabrication is the deposition of a low-bandgap absorber without damaging other device layers. Vapour deposition is thus an attractive method, obviating the need for optically lossy protective interlayers, but is challenging for multi-component perovskites. Here, we demonstrate a method to dual-source co-evaporate low-bandgap perovskite films and devices. We used mixtures formed by melting of metal halides as a single-crucible source of Cs, Pb, and Sn cations. Surprisingly, when this melt was co-evaporated with formamidinium iodide (FAI), uniform and dense perovskite films in the family FA1-xCsxSn1-yPbyI3 were formed. Inclusion of SnF2 in the melt helped to regulate the perovskite’s optoelectronic quality leading to a steady-state power conversion efficiency of ~10% in a solar cell. This represents a new processing paradigm for evaporated perovskite alloys, which is an important step towards all-perovskite multijunction photovoltaics.
22 November 2024 in Nature Communications
Perovskite solar cells (PSCs) offer an efficient, inexpensive alternative to current photovoltaic technologies, with the potential for manufacture via high-throughput coating methods. However, challenges for commercial-scale solution-processing of metal-halide perovskites include the use of harmful solvents, the expense of maintaining controlled atmospheric conditions, and the inherent instabilities of PSCs under operation. Here, we address these challenges by introducing a high volatility, low toxicity, biorenewable solvent system to fabricate a range of 2D perovskites, which we use as highly effective precursor phases for subsequent transformation to α-formamidinium lead triiodide (α-FAPbI3), fully processed under ambient conditions. PSCs utilising our α-FAPbI3 reproducibly show remarkable stability under illumination and elevated temperature (ISOS-L-2) and “damp heat” (ISOS-D-3) stressing, surpassing other state-of-the-art perovskite compositions. We determine that this enhancement is a consequence of the 2D precursor phase crystallisation route, which simultaneously avoids retention of residual low-volatility solvents (such as DMF and DMSO) and reduces the rate of degradation of FA+ in the material. Our findings highlight both the critical role of the initial crystallisation process in determining the operational stability of perovskite materials, and that neat FA+-based perovskites can be competitively stable despite the inherent metastability of the α-phase.