21 October 2020 in International Journal of Control, Automation, and Systems
16 April 2019 in IET Control Theory & Applications
Iterative learning control (ILC) is an effective approach for tracking control system that performs repeating tasks. However, the performance of ILC is significantly deteriorated when the reference is changed. To obtain high tracking performance for both repeating and varying tasks, a novel data‐driven tuning method of feedforward controller structured with infinite impulse response (IIR) filter via ILC is developed in this study. Global optimal parameters of the feedforward controller are obtained by linear least‐squares method based on the optimal feedforward control force obtained by ILC, while model information is not required. Additionally, to deal with the possible instability problem of the feedforward controller structured with IIR filter, a stable approximation approach on the basis of zero‐phase‐error tracking algorithm is presented. The stable approximation approach can convert the approximation problem to a convex optimisation problem. Finally, the proposed approach is compared with the standard ILC and a data‐driven feedforward control structured with finite impulse response filter by two simulation studies. Simulation results demonstrate that the proposed data‐driven feedforward tuning method can achieve high tracking performance and is insensitive to reference variations.
11 February 2021 in IET Control Theory & Applications
This paper proposes a novel performance‐enhanced iterative learning control (ILC) scheme using a model‐free disturbance observer (DOB) to achieve high performance for precision motion systems that encounter non‐repetitive disturbances. As is well known, the performance of the standard ILC (SILC) is severely degraded by the non‐repetitive disturbances. By introducing DOB into SILC, this paper improves the robustness of the ILC system against non‐repetitive disturbances. In the proposed enhanced ILC (EILC), SILC aims at learning the feedforward signals for a specific reference, while DOB is to compensate for external disturbances. Little or no plant model knowledge is required for SILC. To maintain this advantage after introducing DOB, a model‐free design method for DOB is proposed to release the need for the plant model. Based only on a specific reference and the corresponding feedforward signals learned by SILC, the filter of DOB is optimized via an instrumental‐variable estimate method. Numerical simulation is performed to illustrate the effectiveness and enhanced performance of the proposed control approach.
19 August 2020 in IET Control Theory & Applications
This study proposes a novel model‐free output feedback discrete sliding mode control (OFDSMC) with disturbance compensation to achieve high performance for precision motion systems encountering model uncertainties and disturbances. Traditional discrete sliding mode control design requires model and/or state information. In this study, OFDSMC with disturbance compensation is first developed by using a parametric input–output model such that no system states are needed. The essential four control terms of OFDSMC with disturbance compensation is revealed. Then a data‐driven control method is introduced into OFDSMC to eliminate the need for the parametric model. The proposed model‐free OFDSMC facilitates a rapid implementation without either a parameter model or a state observer, and achieves good robustness against model uncertainties and disturbances. Finally, three simulation cases are presented to illustrate the effectiveness and enhanced performance of the proposed approach.
18 September 2023 in Eksploatacja i Niezawodność – Maintenance and Reliability
It remains an important challenge to quantitatively describe the corrosion of reinforced concrete (RC) structures under chloride penetration. When considering the uncertainties encountered throughout the life cycle of RC structures exposed to a corrosive environment and evaluating their safety and reliability, the complexity of the problem intensifies. To address these issues, this paper focuses on the time-dependent reliability analysis of corroded RC beams, utilizing the phase-type (PH) fitting method. Initially, a model for the time-dependent reliability of corroded RC beams is established, incorporating the time-dependent chloride diffusion coefficient. Subsequently, a novel PH fitting method is proposed. The effectiveness of this new method is demonstrated through numerical examples. Furthermore, the time-dependent reliability analysis of corroded RC beams is compared using both the PH fitting method and the Monte Carlo simulation. The results reveal that the proposed method can accurately and efficiently deal with time-dependent reliability problems.
19 January 2026 in IEEE Transactions on Reliability
For traditional surrogate model-based methods, the distribution parameters of random variables will change with the enrichment of the data, ultimately leading to the reconstruction of surrogate model and reassessment of reliability, which often results in a wastage of computational resources. In response, an extended Kriging model-based method is proposed in this paper for efficient reliability analysis under parameters change. Different from the standard Kriging model, in addition to random variables, variable distribution parameters are also included in the proposed method to constitute the extended input variables. In this way, the updated Kriging model with prior parameter information can be directly treated as the initial surrogate model for the posterior problem. Consequently, there is no need to reconstruct the surrogate model if the distribution parameters change, and only one Kriging model is required for this method. The efficiency, robustness and accuracy of the proposed method are demonstrated through three examples. This study contributes to dynamic assessment techniques for structural reliability analysis.