Paper deals with design of traction drive for small electric car where its primary energy source is realized by two hydrogen cells with nominal power 2 × 1,2 kW. Main attention is paid to find appropriate torque-velocity, resp. power-velocity dependences related to wheel of the small electric car. According to these characteristics an appropriate gear ratio is calculated. Finally, an appropriate traction motor is chosen.
In this paper, a comparison of two loss minimization algorithms for induction motor drives derived for the Gamma network and the inverse Gamma network is performed. The basic principle of the algorithm is to find the optimal flux at which the motor has the lowest power losses at the desired torque and speed. The optimal flux is then given as the desired flux to the flux controller in the d-axis. To validate the algorithms, motor models in a stationary frame were first built with non-constant magnetizing inductance and estimation of iron losses and mechanical losses. The proposed algorithms were verified by simulation in Matlab/Simulink environment with real motor parameters. The simulation results confirmed that both algorithms achieve the same efficiency. In terms of derivation complexity, the inverse Gamma network-derived model is simpler.
This paper describes development and experience in modern education in sustainable energy. Up-to-date knowledge from education-research institutions was used to develop of comprehensive online education resources for lifelong learning of professionals from industry and secondary schools' teachers. Nine distance learning modules that cover five thematic fields in sustainable energy were developed. The topics were chosen by considering real knowledge/education needs of the professionals and teachers. To facilitate the complete learning experience, which goes beyond offering only the theory, many virtual experiments and some remote experiments were integrated in the modules. The learning material is designed in such form that it supports the learner at self-learning (by interactive elements in the learning material) and at the self-evaluation of gained knowledge (by automatically assessed e-tests). The modules are available within a modern and user-friendly learning management system (online learning portal) which was especially adapted to support remote and virtual experiments. Three learning modules developed at three different universities are outlined in the paper: (1) Solar Electricity - From Solar cell to system; (2) Power electronics for electric cars, and (3) Drivetrain and combined energy storage system for electric hybrid vehicle.
The paper describe design of battery powered drive unit intended for tree harvester application. Battery powered hybrid drive unit in working machine is currently quite common (1). The battery capacitance is not sufficient to realize harvester as an only battery powered machine. Nevertheless, the hybrid concept of electric drive is useful to cover short power peaks demands during the harvester standard operation. In harvester application there is typical high ratio between short power peak and average demanded power. The development in batteries increases of significance and possibility of electric drive utilization in three harvesters.
The paper deals with design of electric drive for two-tons mini-excavator powered from Lithium battery. Utilization of battery powered excavator has significant benefit in closed areas where the excavators with combustion engine are uncomfortable for working staff. The paper describes the other operational advantages of electric drive in comparison with combustion engine and defines the requirements on battery pack.
This paper deals with the design and operational evaluation of a timber tractor-trailer unit with a hybrid trailer drive. The source of electrical energy for the two induction motors driving the front wheels of the tandem trailer axle is a battery, which is recharged by an induction machine operating as a generator during periods of a lower demand for power from the tractor diesel engine. An electric drive was designed for the defined working cycle of the tractor-trailer unit, and its loading characteristics were tested in the laboratory. The parameters measured on the field tests during timber forwarding were battery voltage and power, and the energy balance. Three adjustment levels of the potentiometer controlling the trailer hybrid drive (50, 75 and 100%) were tested at three different forwarding distances of 100, 500 and 1000 m. Additionally, any slippage of the prime mover wheels and trailer was measured. The maximum peak power taken from the battery was ca. 33 kW during the field tests, whilst the drive was able to deliver a peak output of up to 72 kW for 10 s and permanently up to ca. 50 kW. Even in harsh terrain conditions, the electric drive assisted the combustion engine only when the loaded tractor-trailer unit was travelling uphill. The hybrid drive operation was sustainable for the whole working shift, without the need for recharging when the potentiometer was set to 50%. This appropriate setting of the potentiometer controlling the trailer’s hybrid drive reduced the slipping of the driven wheels of the tractor-trailer unit whilst travelling uphill.