Electronic band convergence can have a beneficial impact on thermoelectric performance, but finding the right band-converged compositions is still time-consuming. We propose a method for designing a series of compositions with simultaneous band convergence in the high-entropy Yb x Ca 1−x Mg y Zn 2−y Sb 2 material by zeroing the weighted sum of crystal-field splitting energies of the parent compounds. We found that so-designed compositions have both larger power factors and lower thermal conductivities and that one of these compositions exhibits a large thermoelectric figure of merit value in comparison with to other p-type Zintls. Our material shows high stability both thermally and temporally. We then assembled an all-Zintl single-stage module, nontoxic and free of tellurium, that demonstrates an exceptional heat-to-electricity conversion efficiency exceeding 10% at a temperature difference of 475 kelvin.
The staggering accumulation of end-of-life lithium-ion batteries (LIBs) and the growing scarcity of battery metal sources have triggered an urgent call for an effective recycling strategy. However, it is challenging to reclaim these metals with both high efficiency and low environmental footprint. We use here a pulsed dc flash Joule heating (FJH) strategy that heats the black mass, the combined anode and cathode, to >2100 kelvin within seconds, leading to ~1000-fold increase in subsequent leaching kinetics. There are high recovery yields of all the battery metals, regardless of their chemistries, using even diluted acids like 0.01 M HCl, thereby lessening the secondary waste stream. The ultrafast high temperature achieves thermal decomposition of the passivated solid electrolyte interphase and valence state reduction of the hard-to-dissolve metal compounds while mitigating diffusional loss of volatile metals. Life cycle analysis versus present recycling methods shows that FJH significantly reduces the environmental footprint of spent LIB processing while turning it into an economically attractive process.
4 April 2023 in Proceedings of the National Academy of Sciences
Two-dimensional (2D) covalent-organic frameworks (COFs) with a well-defined and tunable periodic porous skeleton are emerging candidates for lightweight and strong 2D polymeric materials. It remains challenging, however, to retain the superior mechanical properties of monolayer COFs in a multilayer stack. Here, we successfully demonstrated a precise layer control in synthesizing atomically thin COFs, enabling a systematic study of layer-dependent mechanical properties of 2D COFs with two different interlayer interactions. It was shown that the methoxy groups in COF TAPB-DMTP provided enhanced interlayer interactions, leading to layer-independent mechanical properties. In sharp contrast, mechanical properties of COF TAPB-PDA decreased significantly as the layer number increased. We attributed these results to higher energy barriers against interlayer sliding due to the presence of interlayer hydrogen bonds and possible mechanical interlocking in COF TAPB-DMTP, as revealed by density functional theory calculations.
With the limited resources and high cost of lithium‐ion batteries (LIBs) and the ever‐increasing market demands, sodium‐ion batteries (SIBs) gain much interest due to their economical sustainability, and similar chemistry and manufacturing processes to LIBs. As cathodes play a vital role in determining the energy density of SIBs, Mn‐based layered oxides are promising cathodes due to their low cost, environmental friendliness, and high theoretical capacity. However, the main challenge is structural instability upon cycling at high voltage. Herein, Mg is introduced into the P2‐type Na0.62Ni0.25Mn0.75O2 cathode to enhance electrochemical stability. By combining electrochemical testing and material characterizations, it is found that substituting 10 mol% Mg can effectively alleviate the P2–O2 phase transition, Jahn‐Teller distortion, and irreversible oxygen redox. Moreover, structural integrity is greatly improved. These lead to enhanced electrochemical performances. With the optimized sample, a remarkable capacity retention of 92% in the half cell after 100 cycles and 95% in the full cell after 170 cycles can be achieved. Altogether, this work provides an alternative way to stabilize P2‐type Mn‐based layer oxide cathodes, which in turn, put forward the development of this material for the next‐generation SIBs.
The growth and penetration of lithium dendrites through electrolytes and separators remain key challenges to realizing high–energy density lithium-metal batteries. Using mechanically strong electrolytes and separators has been considered a promising strategy based on the commonly believed softness of lithium. However, dendrite formation persists in stiff solid electrolytes, suggesting distinct mechanical behaviors. We measured the mechanical properties of individual lithium dendrites using an air-free protocol. We found that lithium dendrites are unexpectedly strong and brittle, with fracture stress greater than ~150 megapascals, unlike the ductile bulk metal. Cryo–transmission electron microscopy and mechanical modeling showed that this behavior arises from solid electrolyte interface constraints and nanoscale strengthening. These findings provide alternative mechanisms for dendrite penetration and dead lithium formation as well as guidance for design strategies for lithium-metal batteries.
28 November 2023 in Journal of Colloid and Interface Science