Anion exchange membrane water electrolysis (AEMWE) is an emerging technology for the low-cost production of hydrogen. However, the efficiency and durability of AEMWE devices is currently insufficient to compete with other low-temperature electrolysis technologies. The porous transport layer (PTL) is a critical cell component that remains relatively unoptimized for AEMWE. In this study, we demonstrate that device performance is significantly affected by the morphology and composition of the PTL. For Ni fiber-based PTLs with a ∼2 μm Co3O4 oxygen evolution reaction catalyst layer, decreasing the pore size and porosity resulted in a 20% increase in current density at 2 V in 1 M KOH supporting electrolyte. Alloy PTLs with even lower porosity had a higher performance; in particular, the stainless steel PTL gave an 80% increase in current density relative to Ni. Without Co3O4, the alloy PTLs still demonstrated high activity, indicating that the PTL material was catalytically active. However, characterization of the electrode and electrolyte after testing indicated that the alloy PTLs also underwent restructuring and corrosion processes that may limit long-term stability. This study demonstrates that the design of PTLs with improved morphology and composition is an important area of focus to achieve AEMWE performance targets.
Carbon‐supported Pt nanoparticles are the leading catalysts for the cathode oxygen reduction reaction (ORR) in polymer electrolyte membrane fuel cells. However, these ORR catalysts suffer from poor electrochemical durability, particularly the loss of electrochemical surface area (ECSA) due to Pt nanoparticle dissolution and agglomeration. Here, Pt loss is mitigated through a Pickering emulsion‐processing strategy that employs graphene nanoplatelet dispersions stabilized by the polymer ethyl cellulose. The resulting graphene‐Pt/Vulcan carbon (Pt/C) catalysts exhibit superior durability and ECSA retention throughout an accelerated stress test compared with a commercial Pt/C standard catalyst, both in a diagnostic‐rotating disc electrode setup and in a membrane electrode assembly full cell. These graphene‐Pt/C catalysts also improve durability at high‐voltage conditions, providing further evidence of their exceptional electrochemical stability. Consistent with density functional theory calculations, postelectrochemical characterization reveals that Pt nanoparticles localize at graphene defects both on the basal plane and especially at the edges of the graphene nanoplatelets. Since this Pt nanoparticle localization suppresses Pt nanoparticle dissolution and agglomeration without hindering accessibility of the reactant species to the catalyst surface, the ORR performance under both idealized and practical experimental conditions shows significantly improved durability while maintaining high electrochemical activity.
In situ spectroscopies reveal the increase of Fe and Ni valence states during oxygen evolution in anion-exchange-membrane water electrolyzers (AEMWE) for hydrogen production.
The formation and study of oxygen vacancies are critical for the development of enhanced functional oxides; in the oxygen evolution reaction (OER), oxygen vacancies are proposed to influence the activity and degradation of electrocatalysts. We use thin films of state-of-the-art OER catalyst deposited on crystal substrates with varied lattice parameters to demonstrate the effect of epitaxial strain on oxygen vacancy formation. Through in situ x-ray diffraction under elevated temperatures and reducing conditions of 3% /balance , we show that tensile epitaxial strain makes oxygen vacancy formation more favorable, whereas compressive epitaxial strain has no significant effect compared with an unstrained film. We further use in situ and ex situ x-ray absorption spectroscopy to reveal the effect of strain on the favorability of full reduction of Ir species within films from to and on the energy levels of unoccupied electronic states in the out-of-plane direction, respectively. This study adds experimental evidence for the link between strain and oxygen vacancy formation in thin film perovskites, for which the discussion has been dominated by theory-based approaches.
An improved understanding of catalyst dynamics for the oxygen evolution reaction (OER) in acid is critical for informing the development of highly efficient, stable, and cost‐effective OER catalysts for proton exchange membrane water electrolysis applications. Herein highly tunable, active, and dynamic Ir 5+ materials are studied, Ln3IrO7 (Ln = Pr, Nd, Sm, and Eu). Leveraging a combination of in situ and ex situ characterization, as well as an advanced mercury underpotential deposition technique for Ir surface site quantification, the dynamic nature of Ln3IrO7 materials throughout electrochemical activation under OER conditions is characterized. The trends are elucidated between intrinsic OER activity, surface Ir site quantity, and metal site dissolution behavior as tuned by the Ln site's atomic number. A critical relationship is uncovered to show that maintenance of excellent OER activity throughout performance testing is correlated with a catalysts’ ability to preserve a high degree of Ir enrichment, where heightened stability of Ir sites interestingly parallels reduced stability of Ln sites throughout testing. It is found that as the Ln site's atomic number is decreased, the materials’ intrinsic OER performance improves, due to an increased thermodynamic driving force for Ln dissolution, which is hypothesized to enable the maintenance of highly active Ir‐based surface motifs.