27 January 2021 in IEEE Access
Conventional dc-dc Boost converter has limited boost capacity, and its power device suffers high voltage stress. A novel Z-source based dc-dc boost converter featured with high step-up capability and low device voltage stress is proposed in this paper. The proposed topology can also provide a common ground for input and output, which is lacking in the traditional Z-source topology. Compared with other high step-up topologies, the proposed converter can achieve higher voltage gain under the same duty ratio and maintain low voltage stresses on the switch and diode. Moreover, there are fewer passive components in the proposed structure than in other structures. The steady-state analysis for the continuous conduction mode and discontinuous conduction mode is also provided in this manuscript. Finally, a prototype circuit with 40V-60V input voltage, 400V output voltage and 200W output power is implemented in the laboratory. Experiment results confirm the analysis and the features of the proposed converter.
11 January 2021 in IEEE Access
Conventional dc-dc boost converter has limited boost capacity, and its power device suffers high voltage stress. A novel hybrid Z-source dc-dc converter featured with high step-up capability and low device voltage stress is proposed in this article. Compared with the basic structure, the proposed topology can achieve higher voltage gain under the same duty ratio, and reduce the voltage stresses on the switch and diode under the same output condition. Moreover, the duty ratio is not limited. The detailed analysis and a comparison considering the proposed and other structures are also presented, which confirms its unique advantages. To verify the proposed converter performance, a prototype circuit with 40V-60V input voltage, 400V output voltage and 200W output power is built in the laboratory. Experiment results confirm the analysis and the boost capacity of the proposed converter.
28 July 2023 in IEEE Transactions on Industrial Electronics
For the energy storage dc/dc parallel supply system with low-frequency pulsed load, an unbalanced dynamic power distribution problem will occur due to the inconsistent dc inertia of each converter, even resulting in a severe continuous low-frequency power oscillation. For this, a dynamic power balancing control method is proposed to reshape their dc inertia to be consistent and realize dynamic power balancing distribution among multiple converters without low-frequency power oscillation. Meanwhile, by analogy with the rotor swing equation of the synchronous machine, the power–voltage equivalent model with introducing the dc inertia parameter is established. Afterward, the essential mechanism of power oscillation with a low-frequency pulsed load is revealed. Furthermore, the principle of the proposed control method is clarified, and the control parameters are reasonably designed. Finally, the effectiveness of the proposed control method is verified experimentally.
12 July 2021 in IEEE Access
The Boost type multi-input independent generation system (IGS) with multi-winding simultaneous power supply is proposed and deeply investigated, the important conclusions are obtained. Its circuit structure is composed of a single-stage multi-winding Boost type multi-input inverter with high-frequency-link and a single-stage isolated battery charging/discharging converter connected together at the output end, its circuit topological family includes 4 types of circuit such as full-bridge etc, the maximum power energy management control strategy (EMCS) with output voltage single-loop and three-state one-cycle phase-shift modulation is adopted, and the magnetic saturation of the energy storage inductor and the distortion of output voltage of the IGS are effectively suppressed. By comparing the load power and the total input sources power, the proposed EMCS achieves smooth transition among different power supply modes. The designed and developed 2.5kVA experimental prototype has shown that the proposed IGS has advantages such as single-stage conversion, high frequency galvanic isolation among load, multi-input sources and battery, simultaneous power supply in a high-frequency switching cycle, wide regulating range of duty cycle, small size and light weight, and strong load adaptability, etc.
20 May 2025 in IEEE Transactions on Industrial Electronics
The paralleled DSG-VSGs system provides an effective solution for supplying the low-frequency pulsed load (LFPL). By strategically matching the number of paralleled VSGs to the peak power of the LFPL, the capacity requirement of the DSG can be significantly reduced. Nonetheless, the system encounters power oscillation issues, with the oscillation characteristics varying in response to LFPL pulse frequency and peak-to-average ratio. For this, a transient power deviation model is established to elucidate the power oscillation mechanism, and the underlying causes of oscillation intensification due to LFPL are explored. Moreover, the impact of the pulse frequency and peak-to-average ratio on oscillation characteristics is analyzed. Then, a power oscillation suppression method is proposed to narrow the transient power deviation between the VSGs and DSG, which incorporates a transient compensation component within the VSG excitation system. Thus, the active power oscillation caused by parameter mismatch is effectively suppressed, and the oscillation intensification due to LFPL is alleviated. Finally, experimental validation confirms theoretical analysis and control effectiveness.