Silos are used worldwide to store granular and powdered materials. Agricultural, food and feed products are commonly stored in silos. However, many questions remain unanswered about how to estimate the pressures applied by the bulk material, which are needed to design and calculate the structure of the silo. The complexity of the laws that govern the mechanical behavior of the stored material along with the low number of experimental stations in the world hinder progress in this field. The aim of this study was to elucidate the relationship of the hopper angle, flow pattern and vertical stress at the cylinder-to-hopper transition in slender silos. Therefore, a set of experiments was conducted on a test station to measure the vertical stress produced by maize at the cylinder-to-hopper transition. Five different hopper angles were used. The experiments comprised the filling, the static phase and the discharge. The results obtained show that the hopper angle influences the vertical stress at the cylinder-to-hopper transition. Some bottom configurations (flat bottom and bottom with an angle of 30°) led to vertical stresses that exceeded the value calculated according to Eurocode 1. It is clear that further experimental studies are still necessary to understand the underlying physical phenomena and the relations between pressures, silo geometry and flow pattern of the stored material.
31 August 2021 in REVISTA ENGENHARIA NA AGRICULTURA - REVENG
The objective of this work was to develop models using the Finite Element Method (FEM) to assess the maximum normal pressures in the static condition in silos using different wall friction coefficient and specific weight of the stored product compared to the pressures obtained by the Eurocode 1, part 4. The geometries of the silos models were developed based on the dimensions of the experimental station at the Universidad de Leon (Spain). The material properties were obtained by Jenike shear cell tests and were used to generate the models by the MEF. 3D models were generated varying the friction coefficient (0.2, 0.4, and 0.6) and the specific weight (6; 7.5 and 9 kN / m3). It was verified that the models by FEM follow the theory of pressures in silos: normal pressures increase due to the increase in specific weight and decrease due to the increase in the friction coefficient. Moreover, the maximum normal pressure occurs at the hopper silo transition. The experimental pressures (FEM models) compared with Eurocode 1, part 4 allowed to validate the models developed, presenting trends of similar values to those found by the MEF. The experimental models demonstrated that the influence of the wall friction coefficient and specific weight significantly interferes with the pressures in slender silos.
31 October 2020 in Research, Society and Development
The building construction is responsible for the largest industrial sectors in the world, with high energy demand and use of natural resources. Given the scarcity of natural resources and the energy crisis, the use of waste in building materials becomes a target. Therefore, this study aimed to evaluate different treatments with pine sawdust and coffee husk additions, both at 10% by mass and also evaluated in drying and burning. The treatments were evaluated by bulk density, linear shrinkage and compressive strength. In the treatments without burning, it was possible to verify that the addition of 10% of residue reduces the mechanical resistance of the material considerably but improves the physical properties. In the burned materials, it was observed that the addition of residues is unsatisfactory due to the high temperature, carbonizing them, increasing the porosity, thus destabilizing the material, negatively affecting the physical and mechanical properties.
4 November 2026 in Theoretical and Applied Engineering
Technological advances have fostered the widespread use of computational tools in structural engineering, enabling more representative and detailed analyses. The grillage analogy, applied through the Finite Element Method (FEM), is an effective approach for slab analysis. In ANSYS®, this technique can be implemented through APDL (ANSYS Parametric Design Language) input files; however, their manual generation is time-consuming and laborintensive, often requiring thousands of command lines. This study developed a Python-based computational routine to automate the generation of APDL files for grillage-based analysis of slabs and edge beams in ANSYS®. The generated models were validated against slab analyses reported in the literature. Percentage differences in bending moments ranged from 0.21% to 5.09%. The expanded validation included torsional moments and vertical deflections. For torsional moments, differences of 14.44% and 17.53% were obtained for J = 100% and J = 15%, respectively, while reducing J from 100% to 15% decreased the torsional moment by 72.33% in the developed model and 73.06% in the reference study. Vertical deflections showed close agreement with reference values, with differences of 1.08% and 1.48% for the analyzed mesh discretizations. Overall, the APDL Generator provided consistent numerical results while automating the modeling process, supporting its applicability to grillage-based slab analysis in ANSYS®.