Giovanni Pio Pucillo

Giovanni Pio Pucillo

Auto-generated profile, based on publicly available information

Giovanni Pio Pucillo

University of Naples Federico II, Naples, Italy

Research Focus & Metrics

Academic Career Length

17Years (2010-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
14 September 2016 in Vehicle System Dynamics
Verified
Journal Article
Closed access
GPGiovanni Pio Pucillo
Giovanni Pio Pucillo
Because thermal expansions are constrained within continuous welded rail track, the track can buckle, and does so mainly in the horizontal plane. In this paper, a parametric finite element model of railway track is presented, and its sensitivity to the variations of the main parameters that characterise the scenario has been investigated and discussed. Comparison with existing literature shows good agreement. It is found that curved tracks suffer from thermal buckling more than tangent tracks do. To simulate a track misalignment defect, a new methodology has been utilised that does not introduce, as is usual, geometrical discontinuities near the same defect, because it takes into account – in a natural way – the bending stiffness of the whole railway track in the horizontal plane. To contribute to a better understanding of the safe utilisation of raw experimental data obtained from in situ tests, a deep analysis of the effects on the thermal track buckling response produced by each parameter characterising the sleeper–ballast lateral resistance curve is presented and discussed. It is found that for current ballasted railway tracks, the minimum buckling temperature depends only on the limit lateral resistance, whereas a high value of the initial stiffness can lead to overestimation of the maximum buckling temperature, also taking into account the ‘natural’ decrease in the maximum buckling temperature due to an increase in the railway-traffic-induced defect amplitude.

18 December 2016 in Proceedings of the Institution of Mechanical Engineers, Part F: Journal of Rail and Rapid Transit
Verified
Journal Article
Open access
AIAntonio De Iorio
Antonio De Iorio
Marzio GrassoMarzio Grasso
Marzio Grasso
FPFrancesco Penta
Francesco Penta
GPGiovanni Pio Pucillo
Giovanni Pio Pucillo
SRStefano Rossi
Stefano Rossi
MTMario Testa
Mario Testa
In service, railway tracks must withstand the transverse and longitudinal forces that are caused by running vehicles and thermal loads. The mechanical design that adopts any of the track models available in the technical literature requires that the strength of the track is fully characterised. In this paper, the results of an experimental research activity on the sleeper–ballast resistance along the lateral and the longitudinal directions are reported and discussed. In particular, the work is aimed at identifying the strength contributions offered by the base, the ballast between the sleepers, and the ballast shoulder to the global resistance of the track in the horizontal plane. These quantities were experimentally determined by means of an ad hoc system designed by the authors. Field tests were carried out on a series of track sections that were built to simulate scenarios in which the ballast was removed from the crib and/or the shoulder. The results of this study indicate that the strength percent contributions from the crib, the sleeper base, and the shoulder are, respectively, equal to about 50%, 25%, and 25% in the lateral direction, and 60%, 30%, and 10% in the longitudinal direction. Moreover, the comparison of the acquired data with literature results reveals that a detailed knowledge about the testing conditions and the activated ballast failure mechanisms is needed in order to correctly use the test data for the design purpose.

1 October 2017 in Mechanics Research Communications
Verified
Journal Article
Closed access
FPFrancesco Penta
Francesco Penta
MMMichelina Monaco
Michelina Monaco
GPGiovanni Pio Pucillo
Giovanni Pio Pucillo
AGAntonio GESUALDO
Antonio GESUALDO

1 June 2013 in Journal of Food Engineering
Verified
Journal Article
Closed access
Daniele NaviglioDaniele Naviglio
Daniele Naviglio
AFAndrea Formato
Andrea Formato
GPGian Pio Pucillo
Gian Pio Pucillo
Monica GalloMonica Gallo
Monica Gallo

28 June 2017 in Journal of Mechanics of Materials and Structures
Verified
Journal Article
Closed access
PDF file
AGAntonio GESUALDO
Antonio GESUALDO
Antonino IannuzzoAntonino Iannuzzo
Antonino Iannuzzo
FPFrancesco Penta
Francesco Penta
GPGiovanni Pio Pucillo
Giovanni Pio Pucillo
In this paper an homogenization procedure of a Vierendeel girders with elastic joints is shown. The method is based on the Stephen transfer matrix analysis and employs as substitute continuum a polar Timoshenko beam. The polar character of the equivalent beam arises quite naturally from the analysis of the pure bending eigenvector components of the girder force transfer matrix. Through the girder unit cell, two bending moments are transmitted: one is generated by the couple of axial forces acting\ud on each nodal section of the beam, the other is produced by the moments applied at the nodes of every ones by the adjacent cells and is modelled as the resultant of the micro-polar moments. Transfer force eigenvector analysis reveals that the unit cell bends maintaining the webs undeformed, a property that allows evaluating both the bending stiffnesses and the equivalent material micro-polar scale parameter by means of straightforward equations. The accuracy of the proposed method is verified by comparing the predictions of the homogenized model with literature data and with the results of the analysis of a series of girders carried out by the finite element method

10 September 2014 in Fracture and Structural Integrity
Verified
Journal Article
Open access
PDF file
AIAntonio De Iorio
Antonio De Iorio
Marzio GrassoMarzio Grasso
Marzio Grasso
FPFrancesco Penta
Francesco Penta
GPGiovanni Pio Pucillo
Giovanni Pio Pucillo
VRVincenzo Rosiello
Vincenzo Rosiello
In the present paper, testing methods currently adopted to measure the in service ballast resistance are synthetically reviewed to identify the main sources of uncertainty influencing the test loads and to define an experimental methodology allowing the optimal control of the testing parameters without the introduction of spurious or parasitic actions on the track sample. An alternative testing system, which allows applying on a fullscale sample of a railway track testing loads very close the real ones, is presented. Of the new system, both the ways of use for measuring the transversal and axial ballast strength, the general procedure to carry out the experimentation and its application to a real scenario are described, highlighting its main advantages in terms both of modalities for applying the loads and of testing parameter control.