Yuriy Abrashkevich

Yuriy Abrashkevich

Auto-generated profile, based on publicly available information

Yuriy Abrashkevich

Kyiv National University of Construction and Architecture Kyiv Povitryanykh Syl Avenue 31 03037

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
26 June 2023 in Strength of Materials and Theory of Structures
Verified
Journal Article
Open access
PDF file
YMYuriy Maksimyuk
Yuriy Maksimyuk
KPKostyantyn Pochka
Kostyantyn Pochka
YAYuriy Abrashkevych
Yuriy Abrashkevych
MPMykola Prystailo
Mykola Prystailo
APAndriy Polishchuk
Andriy Polishchuk
In order to carry out experimental studies of the process of cutting highly abrasive materials with abrasive reinforced wheels, a dynamometer stand for registering the force load of the author's design of the KNUCA was modified, which made it possible to conduct full-fledged experimental studies taking into account all the valid factors of the interaction of the working environment and the working body during cutting with the supply of water to the cutting zone to dedust the working process The use of refractory bricks is proposed as the working environment, and the abrasive reinforced wheel for cutting highly abrasive materials with a strength of up to 60MPa is used as the working body. As a result of the research conducted for the dynamometric stand for force load registration during the study of the process of cutting highly abrasive materials with an abrasive reinforced wheel, the tangential forces that perform the work of destruction and overcoming friction between the side surfaces of the wheel and the material were analytically determined. According to the results of theoretical studies, it was established that the limits of the change in the resistance to cutting, determined for a natural installation for cutting highly abrasive materials (refractories) with an abrasive reinforced wheel and for a laboratory stand, are the same, and the nature of their change is also similar and related by a similarity coefficient. In order to check the adequacy of theoretical calculations, experimental studies of cutting refractory bricks with temporary resistance to uniaxial compression of the rock σв=60 MPa were carried out on a dynamometric stand. The conducted experimental studies fully confirm the adequacy of the theoretical calculations, and the comparison of the theoretical and experimental results of determining the tangential cutting forces showed their sufficient convergence and, accordingly, the legitimacy of using analytical expressions when calculating the power parameters of machines with an abrasive tool. The maximum value of the error in determining the tangential cutting forces theoretically and experimentally on the laboratory bench for recording the cutting forces of highly abrasive materials with abrasive reinforced wheels is Δδ=13,8%.

30 May 2022 in Strength of Materials and Theory of Structures
Verified
Journal Article
Open access
PDF file
YAYurii Abrashkevych
Yurii Abrashkevych
HMHryhorii Machyshyn
Hryhorii Machyshyn
OMOleksandr Marchenko
Oleksandr Marchenko
MBMaksym Balaka
Maksym Balaka
OZOlena Zhukova
Olena Zhukova
The mechanical strength of unreinforced abrasive wheels is determined by centrifugal and bending forces, but their distribution during reinforcement is unknown. It was assumed that the stresses are distributed evenly, but a comparison of calculations on the theory of elasticity and real characteristics on a special stand showed complete discrepancy. Tensile tests of the wheels made it possible to compare the stresses results in the circumferential and radial directions. Was found that the reinforced wheel is an anisotropic body. Anisotropy can be reduced by displacing one reinforcement mesh relatively to the other by angle of 45°. In this paper, a mathematical model of the stress-strain state of the abrasive reinforced wheel was developed, taking into account the anisotropy of its properties. To determine the centrifugal forces, the theory of elasticity for an orthotropic body is applied. The bending forces that arise in the working wheel were determined during solving the problem of the distribution of deformations in the anisotropic annular plate rigidly fixed along the inner contour. As a result of experimental studies, it was found that stresses reach 8...23 MPa, which can be compared with the ultimate strength of the wheel matrix. The elastic module of the wheel matrix is noticeably greater than the elastic module of the reinforcing mesh, which practically does not perceive the load at the initial stage. The developed mathematical model of the strength indicators for abrasive reinforced wheels makes it possible to predict their reliability and safe operation.

29 July 2021 in Gіrnichі, budіvelnі, dorozhnі ta melіorativnі mashini
Verified
Journal Article
Open access
PDF file
YAYury Abrashkevich
Yury Abrashkevich
HMHrigoriy Machyshyn
Hrigoriy Machyshyn
OMOleksandr Marchenko
Oleksandr Marchenko
SKSvitlana Komotska
Svitlana Komotska
Carrying out of the clearing operations at carrying out mechanized processing of construction equipment from paints and varnishes, rust, various kinds of pollution belongs to mass labour-consuming operations [1]. To carry out these operations, widespread use of hand-held machines, working bodies that have abrasive wheels and metal brushes. The versatility and versatility of these machines, combined with the correct selection of the desired abrasive work tool, can significantly accelerate and facilitate the performance of cleaning and grinding operations with the desired effect. However, most of them have drawbacks in the cleaning of thin-sheet metal, since the removal of the base metal also takes place, which in most cases is not acceptable. So when processing non-metallic materials with metal brushes the working surface is clogged with small particles of metal, which subsequently leads to the formation of rust, and when cleaning the metal surfaces grooves are formed. Metal brushes are also ineffective in cleaning surfaces of synthetic enamels, curvilinear surfaces and inaccessible areas. Machining these tools is energy-intensive and requires the use of heavy-duty hand machines. Fiber and petal abrasive tools are not self-cleaning and lose their cutting power due to the filling of the intergranular space with cleaning waste. Sand blasting is environmentally hazardous for workers and the environment, since the sand consumables fly over long enough distances (especially when clearing tall structures and structures). The analysis showed that one of the effective tools for cleaning metal and non-metal surfaces from paint coatings, rust and other contaminants without removing the base material layer is a polymer-abrasive brush. However, there is insufficient research on the mechanism of its operation, energy and thermal processes that occur during operation and have a decisive influence on the performance of the polymer-abrasive brush. The results of studies of the influence of structural and mode parameters of manual angle grinders with polymer-abrasive brushes are presented in the paper. The study of these issues is an urgent task, as it will allow to determine the parameters of the drive machine, rational modes and schemes of their operation, as well as the scope of use of such working bodies.

30 December 2022 in Gіrnichі, budіvelnі, dorozhnі ta melіorativnі mashini
Verified
Journal Article
Open access
PDF file
YAYuriy Abrashkevich
Yuriy Abrashkevich
MPMykola Prystaylo
Mykola Prystaylo
APAndriy Polishchuk
Andriy Polishchuk
The cost of abrasive cutting is mainly determined by the wear resistance of the abrasive wheel, which consists of abrasive grain, filler, phenolic binder and glass mesh. Due to the fact that during the cutting process, as a result of the summation of heat pulses from the cutting grains located on the cutting edge of the wheel, a significant amount of heat is released, high temperature values are reached in the cutting zone. Meanwhile, it is well known that the phenolic binder has low heat resistance, it breaks down at a temperature of 520-570 °K, therefore the nature of the thermal processes occurring during abrasive cutting determines the temperature in the circle and, accordingly, the speed of its wear. Ideally, of course, the speed of thermal destruction of the bond should correlate with the speed of mechanical destruction of abrasive grains, so that cutting is carried out only with sharp, unfired grains, while only blunt grains should be removed from the cutting edge. Since the rate of abrasion of abrasive grains is different for different processed materials, the characteristics of binders must also depend on the type of processed material, that is, it is necessary to create abrasive wheels for cutting different materials. In practice, abrasive wheels are produced without special consideration of the features of the cut material, which is largely explained by the lack of clarity of the nature of thermal processes in abrasive reinforced wheels and technological difficulties associated with changing the thermophysical properties of the wheels.

2 April 2025 in Gіrnichі, budіvelnі, dorozhnі ta melіorativnі mashini
Verified
Journal Article
Open access
PDF file
KPKostiantyn Pochka
Kostiantyn Pochka
YAYuriy Abrashkevich
Yuriy Abrashkevich
MPMykola Prystaylo
Mykola Prystaylo
APAndrii Polishchuk
Andrii Polishchuk
OSOleksander Skochko
Oleksander Skochko
АПАндрій Поліщук
Андрій Поліщук
At the present stage of development of the processing of solid materials, the science of cutting materials is intensively developing in such cardinal directions as the search for new effective tool materials; in-depth study of cutting physics; improving the quality of the formed surfaces along with the need to intensify operating modes, in particular, cutting speed; creation of new effective lubricating and cooling media; research and systematization of the experience of machinability of the latest structural materials – high-strength and heat-resistant steels and alloys, synthetic materials with various properties, refractory materials, graphite and carbon fibers, parts made of hard alloys of all grades, fiberglass-reinforced plastics, various semiconductor materials of finishing materials and products made of natural stone; development of technical standards for all known types of cutting processing; Optimization of cutting operations on automated equipment, in particular on CNC machines and in flexible automated production environments. Cutting natural and artificial stone materials is an operation, in the process of which a wide range of materials with different physical and mechanical properties is to be processed.

30 December 2025 in Gіrnichі, budіvelnі, dorozhnі ta melіorativnі mashini
Verified
Journal Article
Open access
PDF file
YAYuriy Abrashkevich
Yuriy Abrashkevich
MPMykola Prystaylo
Mykola Prystaylo
OMOleksander Marchenko
Oleksander Marchenko
APAndrii Polishchuk
Andrii Polishchuk
VKViktor Kolomiets
Viktor Kolomiets
ВКВіктор Коломієць
Віктор Коломієць
The article considers the issue of increasing the performance of abrasive reinforced wheels used in the processes of cutting and grinding metals and building materials. The analysis of the design features of wheels with smooth and rough side surfaces is carried out and their influence on cutting efficiency, thermal processes and safety of work is investigated. Physical models have been proposed to explain the reasons for tool jamming during cutting rolled metal, taking into account the elastic deformations of the material and the action of mortise forces. It is shown that the use of wheels with rough side surfaces provides microcutting with protruding abrasive grains, reduces friction, improves heat dissipation and improves the quality of the treated surface. It has been established that such wheels are characterized by greater wear resistance (by 20–30%), reduced likelihood of jamming and increased safety of operation compared to traditional wheels with smooth surfaces. The practical significance of the results obtained lies in the possibility of using them to improve the design of abrasive tools and increase the productivity and reliability of cutting processes in metallurgy, construction and mechanical engineering.