Heein Yoon

Heein Yoon

Auto-generated profile, based on publicly available information

Heein Yoon

Department of Electrical Engineering, Ulsan National Institute of Science and Technology, Ulsan, South Korea

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
11 September 2019 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Closed access
JKJuyeop Kim
Juyeop Kim
YLYounghyun Lim
Younghyun Lim
HYHeein Yoon
Heein Yoon
YLYongsun Lee
Yongsun Lee
HPHangi Park
Hangi Park
JCJaehyouk Choi
Jaehyouk Choi
This article presents a cascaded architecture of a frequency synthesizer to generate ultra-low-jitter output signals in a millimeter-wave (mmW) frequency band from 28 to 31 GHz. The mmW-band injection-locked frequency multiplier (ILFM) placed at the second stage has a wide bandwidth so that the performance of the jitter of this frequency synthesizer is determined by the GHz-band, digital subsampling phase-locked loop (SSPLL) at the first stage. To suppress the quantization noise of the digital SSPLL while using a small amount of power, the optimally spaced voltage comparators (OSVCs) are presented as a voltage quantizer. This article was designed and fabricated using 65-nm CMOS technology. In measurements, this prototype frequency synthesizer generated output signals in the range of 28-31 GHz, with an rms jitter of less than 80 fs and an integrated phase noise (IPN) of less than -40 dBc. The active silicon area was 0.32 mm 2 , and the total power consumption was 41.8 mW.

13 February 2021
Verified
Conference Paper
Closed access
SYSeyeon Yoo
Seyeon Yoo
SPSuneui Park
Suneui Park
SCSeojin Choi
Seojin Choi
YCYoonseo Cho
Yoonseo Cho
HYHeein Yoon
Heein Yoon
JCJaehyouk Choi
Jaehyouk Choi
As the utilization of the mm-wave spectrum becomes active, designers' interests are shifting to even higher frequencies in the W-band. Given their potential use as carrier frequencies for the next-generation mobiles (i.e., beyond 5G), these W-band signals must have ultra-low phase noise (PN). Currently, the most popular solution to generate such frequencies is with a cascaded architecture: a first-stage PLL generates a low-PN signal at a relatively low frequency at which the VCO LC tank has a high Q factor, and following frequency multipliers (FMs) increase the frequency to the W-band [1]. Although various FMs have been proposed, all of them are limited in their ability to achieve a high multiplication factor, M. Push-push or harmonic-selection circuits have high conversion losses. Injection-locked FMs (ILFMs) require multiple stages due to their narrow lock ranges, which increase power consumption and complexity. Thus, single-stage direct PLLs [2-4] would be preferred if they could have a sufficiently wide loop bandwidth to suppress the poor PN of a W-band VCO. Subsampling PLLs (SSPLLs) are suitable for extending the bandwidth since they have low in-band PN due to the high phase-error (φ ERR ) detection gain of a subsampling phase detector (PD). Nevertheless, when SSPLLs operate in the W-band, the degradation of PN is unavoidable because the φ ERR detection gain decreases as the frequency of the VCO, f VCO , increases. As described at the left of Fig. 23.4.1, when the switch of the PD, SWPD, is closed, the output of the PD, SPD, should track the signal of the VCO, S VCO , closely. However, when f VCO increases to the W-band, the amplitude of SPD is reduced significantly by a parasitic pole that is present due to the turned-on resistance of SW PD , R ON , and the sampling capacitor, CS. When SWPD is turned off, φ ERR is detected in SPD, but its magnitude is already suppressed significantly relative to that in SVCO. This effect also can be interpreted in the frequency domain where S VCO is suppressed by a low-pass filter before the information of φ ERR is extracted at the baseband frequencies.

8 February 2019 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Closed access
HYHeein Yoon
Heein Yoon
SPSuneui Park
Suneui Park
JCJaehyouk Choi
Jaehyouk Choi
This paper presents a low-jitter, injection-locked frequency generator that can provide multiple output frequencies concurrently. The injection-locked digitally controlled oscillators (DCOs) can be controlled separately so that their output frequencies can be changed independently between 0.9 and 1.2 GHz in 15-MHz steps. Due to the proposed time-interleaved frequency calibrator that operates continuously in the background, all injection-locked DCOs are ensured to maintain excellent jitter performance against process, voltage, and temperature (PVT) variations. As a prototype, the proposed injection-locked, multi-frequency generator (ILMFG) was designed to generate two independently controlled output signals, and it was fabricated in a 65-nm CMOS technology. The 1-MHz phase noise and the rms jitter integrated from 1 kHz to 40 MHz of the 960-MHz output signal were -133.5 dBc/Hz and 375 fs, respectively. The degradation of rms jitter was restricted to less than 10%. The silicon area was 0.05 mm², and the total power consumption was 7.7 mW when generating two different output frequencies.

10 January 2025 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Closed access
SJSeohee Jung
Seohee Jung
JKJaeho Kim
Jaeho Kim
JBJooeun Bang
Jooeun Bang
SLSarang Lee
Sarang Lee
HYHeein Yoon
Heein Yoon
JCJaehyouk Choi
Jaehyouk Choi
This work presents a D-band frequency synthesizer that can generate an ultra-low jitter output signal over a large frequency-tuning range (FTR). To overcome the structural limitations of conventional sub-terahertz (sub-THz) frequency synthesizers and concurrently achieve a low jitter and a large FTR, we designed a two-stage architecture, in which a 50-GHz band subsampling PLL (SSPLL) with a 3rd-harmonic (HM)-rich class-F voltage-controlled oscillator (VCO) in the first stage interoperated with an HM-boosting frequency multiplier (FM) in the second stage. Designed with a 40-nm CMOS process, this D-band frequency synthesizer exhibited a wide FTR of 11.8%, i.e., 144–162 GHz. Due to its high-gain subsampling phase detector (PD), which can suppress in-band phase noise (PN), and its class-F VCO, which can achieve low out-of-band (OOB) PN, the proposed frequency synthesizer achieved the lowest rms jitter (i.e., 39 fsrms). Since the combination of the 3rd-HM-rich class-F VCO and the HM-boosting FM generated a D-band output signal in a power-efficient manner, this work also achieved the best jitter figure-of-merit (FOM) among the state-of-the-art W/D-band frequency synthesizers with an FTR more than 5%.

24 October 2024 in IEEE Transactions on Circuits and Systems II: Express Briefs
Verified
Journal Article
Closed access
HAHyogyoung An
Hyogyoung An
HNHyeonjun Nam
Hyeonjun Nam
SKSungjin Kim
Sungjin Kim
YLYounghyun Lim
Younghyun Lim
HYHeein Yoon
Heein Yoon
An area-efficient CMOS cross-coupled LC-VCO, operating from 5.74 GHz to 8.02 GHz and featuring a tail noise filter with two tail inductors integrated inside the main inductor, is presented for the first time. The tail noise filter comprised two nested intertwined tail inductors (NITIs) and a tail capacitor bank, effectively suppressing phase noise (PN) while generating negligible magnetic couplings between the main inductor and the NITIs. The proposed architecture enables area-efficient CMOS cross-coupled design, even with the two NITIs, but has no performance degradation, i.e., it eliminates the additional area for the tail noise filter. Implemented in 28-nm CMOS process, it consumed 11 mA current from 0.73 V power supply. The LC-VCO achieved PN of −116.38 dBc/Hz at 1 MHz offset frequency for an output frequency of 5.747 GHz. 37% and 27% reductions in silicon area were achieved, over the conventional LC-VCO and an LC-VCO using intertwined tail inductors (ITIs), respectively, without compromising on performance. The proposed design has the smallest area among state-of-the-art LC-VCOs that include a tail noise filter along with competitive PN and frequency tuning range (FTR).

3 September 2025 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Closed access
CAChangmin An
Changmin An
HAHyogyoung An
Hyogyoung An
HNHyeonjun Nam
Hyeonjun Nam
HYHeein Yoon
Heein Yoon
This work presents an output-capacitor-less digital-assisted analog low-dropout regulator digital-assisted analog LDO (DA-ALDO) that employs a seamless digital-to-analog transfer (D2A-TF) technique enabled by a local ground generator (LGG). The proposed architecture extracts only the strengths of digital LDOs (DLDOs)—fast transient response and low voltage droop—and analog LDOs (ALDOs)—high power supply rejection ratio (PSRR)—to achieve an optimized performance without inheriting their drawbacks. The proposed DA-ALDO is fabricated in a 28-nm CMOS process and achieves a PSRR of −57.6 and −53.7 dB at 10 kHz under load currents of 1 and 100 mA, respectively. It exhibits a voltage droop of only 54mV and a fast settling time of 667 ns in response to a 99-mA load step while consuming a quiescent current of $338.5~{\mu }$ A. The regulator occupies a compact active area of 0.032 mm2 and achieves a figure of merit (FoM) of 0.029 ps.