Xin Zhuo

Xin Zhuo

Auto-generated profile, based on publicly available information

Xin Zhuo


Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
11 November 2023 in Wear
Verified
Journal Article
Closed access
XZXin Zhuo
Xin Zhuo
JCJun Cao
Jun Cao
HHHaibo Huang
Haibo Huang
LLLi Liu
Li Liu
XSXinkun Suo
Xinkun Suo
ZAZeshan Abbas
Zeshan Abbas

14 October 2026 in Tribology International
Verified
Journal Article
Closed access
XZXin Zhuo
Xin Zhuo
FLFeng Lu
Feng Lu
DHDonghan Huang
Donghan Huang
XMXiuwen Ma
Xiuwen Ma
JCJiaying Chen
Jiaying Chen
Zhenzhong WangZhenzhong Wang
Zhenzhong Wang

16 April 2026 in SSRN Electronic Journal
Verified
Preprint
Open access
XZXin Zhuo
Xin Zhuo
TDTao Dang
Tao Dang
YMYile Mao
Yile Mao
LLLi Liu
Li Liu
Michel FillonMichel Fillon
Michel Fillon
JCJun Cao
Jun Cao
Severe degradation of tribological performance and surface cavitation damage were frequently observed in water-lubricated bearings subjected to low-speed, heavy-load, and frequent start-stop operating conditions. To extend the service life and investigate the influence of substrate hardness and elastic modulus on coating performance, PI/PTFE coatings were prepared on CuPb22.5Sn2.5 copper alloy and 45# steel surfaces via liquid spraying. Furthermore, Molecular Dynamics (MD) simulations were employed to analyze the interfacial interactions, revealing that the shear deformation of polymer chains dominated the interfacial friction. Experimental results indicated that the copper-based coating exhibited superior tribological performance compared to the steel substrate due to higher H/E and H³/E² ratios under dry friction, reducing the coefficient of friction (CoF) and wear rate by 59.2% and 16.6%, respectively. Additionally, three-body abrasion and abrasive wear were effectively mitigated by the coating compared with the uncoated copper alloy, yielding significant decreases of 65.7% and 19.7% in CoF and wear rate. However, under seawater lubrication, tribological performance was primarily governed by the coupling effect between the coating’s mechanical properties and the lubrication environment. Consequently, the steel-based coating exhibited tribological performance comparable or superior to the copper-based system. Furthermore, in seawater cavitation experiments, the steel-based coating demonstrated the highest erosion resistance, reducing mass loss by 28.7% relative to the uncoated copper alloy, as its H³/E² value effectively withstood mechanical impacts. In summary, the tribological behavior and cavitation resistance were primarily governed by plastic deformation resistance (characterized by H/E and H³/E² ratios) and the material-medium coupling effect under specific lubrication conditions.

3 February 2026 in SSRN Electronic Journal
Verified
Preprint
Open access
XZXin Zhuo
Xin Zhuo
TDTao Dang
Tao Dang
YMYile Mao
Yile Mao
LLLi Liu
Li Liu
Michel FillonMichel Fillon
Michel Fillon
JCJun Cao
Jun Cao
Severe degradation of tribological performance and surface cavitation damage were frequently observed in water-lubricated bearings subjected to low-speed, heavy-load, and frequent start-stop operating conditions. To extend the service life and investigate the influence of substrate hardness and elastic modulus on coating performance, PI/PTFE soft coatings were prepared on CuPb22.5Sn2.5 copper alloy and 45# steel surfaces via liquid spraying. Furthermore, Molecular Dynamics (MD) simulations were employed to analyze the interfacial interactions between the substrate and the coating under dry friction at the atomic scale, elucidating microscopic wear mechanisms. Results indicated that the coating on the copper alloy exhibited superior tribological performance compared to the steel substrate under dry friction, attributed to higher H/E and H³/E² ratios. Specifically, the coefficient of friction (CoF) and wear rate of the coating on the copper alloy were reduced by 59.2% and 16.6%, respectively. Additionally, three-body abrasion and abrasive wear were effectively mitigated by the coating compared with the uncoated copper alloy, resulting in significant decreases of 65.7% and 19.7% in CoF and wear rate, respectively. However, under seawater lubrication, tribological performance was primarily governed by the coupling effect between the coating's mechanical properties and the lubrication environment. Consequently, the coating on the steel substrate exhibited tribological performance comparable or superior to the copper-based system. In summary, the tribological behavior of the coatings was primarily governed by the resistance to plastic deformation (characterized by H/E and H³/E² ratios) and the coupling effect between the material and the medium under specific lubrication conditions.

17 June 2026 in SSRN Electronic Journal
Verified
Preprint
Open access
XZXin Zhuo
Xin Zhuo
TDTao Dang
Tao Dang
YMYile Mao
Yile Mao
LLLi Liu
Li Liu
SLShuting Li
Shuting Li
JCJun Cao
Jun Cao
Severe degradation of tribological performance and surface cavitation damage were frequently observed in water-lubricated bearings subjected to low-speed, heavy-load, and frequent start-stop operating conditions. To extend the service life and investigate the influence of substrate hardness and elastic modulus on coating performance, PI/PTFE coatings were prepared on CuPb22.5Sn2.5 copper alloy and 45# steel surfaces via liquid spraying. Furthermore, Molecular Dynamics (MD) simulations were employed to analyze the interfacial interactions, revealing that the shear deformation of polymer chains dominated the interfacial friction. Experimental results indicated that the copper-based coating exhibited superior tribological performance compared to the steel substrate due to higher H/E and H³/E² ratios under dry friction, reducing the coefficient of friction (CoF) and wear rate by 59.2% and 16.6%, respectively. Additionally, three-body abrasion and abrasive wear were effectively mitigated by the coating compared with the uncoated copper alloy, yielding significant decreases of 65.7% and 19.7% in CoF and wear rate. However, under seawater lubrication, tribological performance was primarily governed by the coupling effect between the coating’s mechanical properties and the lubrication environment. Consequently, the steel-based coating exhibited tribological performance comparable or superior to the copper-based system. Furthermore, in seawater cavitation experiments, the steel-based coating demonstrated the highest erosion resistance, reducing mass loss by 28.7% relative to the uncoated copper alloy, as its H³/E² value effectively withstood mechanical impacts. In summary, the tribological behavior and cavitation resistance were primarily governed by plastic deformation resistance (characterized by H/E and H³/E² ratios) and the material-medium coupling effect under specific lubrication conditions.