Kensuke Nakanishi

Kensuke Nakanishi

Auto-generated profile, based on publicly available information

Kensuke Nakanishi

Toshiba Corporation, Kawasaki 212-8580, Japan

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
9 November 2018 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Closed access
SKShusuke Kawai
Shusuke Kawai
RIRui Ito
Rui Ito
KNKengo Nakata
Kengo Nakata
YSYutaka Shimizu
Yutaka Shimizu
MNMotoki Nagata
Motoki Nagata
TMToshiya Mitomo
Toshiya Mitomo
A fully integrated 4 x 4 802.11abgn/ac/ax transceiver system-on-chip (SoC) with integrated interference analyzer and frequency-dependent in-phase and quadrature (IQ) (FD-IQ) calibration is presented. The FD-IQ technique helps meeting the extremely strict IQ imbalance requirement for 1-K quadratic-amplitude modulation (QAM). The pure current-mode TX baseband (BB) improves SNR to better than 50 dB, and a multi-mode local oscillator (LO) distribution circuit provides non-contiguous operation with the error vector magnitude (EVM) of less than -37 dB. The integrated interference analyzer achieves the highly reliable connection in the presence of the undesired signal and hence improves the frequency usage efficiency by identifying the wireless LAN (WLAN) and other signals in the 2G/5G band.

11 July 2014 in IEEE Communications Letters
Verified
Journal Article
Open access
KNKensuke Nakanishi
Kensuke Nakanishi
SHShinsuke Hara
Shinsuke Hara
TMTakahiro Matsuda
Takahiro Matsuda
KTKenichi Takizawa
Kenichi Takizawa
FOFumie Ono
Fumie Ono
RMRyu Miura
Ryu Miura
Delay tomography has so far burdened source and receiver measurement nodes in a network with two requirements: path establishment and clock synchronization between them. In this letter, we focus on the clock synchronization problem in delay tomography and propose a synchronization-free delay tomography scheme based on compressed sensing. The proposed scheme selects a path between source and receiver measurement nodes as the reference path, which results in a loss of equation in a conventional delay tomography problem. By utilizing compressed sensing, however, the proposed scheme becomes robust to the loss. Simulation experiments confirm that the proposed scheme works comparable to a conventional delay tomography scheme in a network with no clock synchronization between source and receiver measurement nodes.

1 February 2018
Verified
Conference Paper
Closed access
SKShusuke Kawai
Shusuke Kawai
HAHiromitsu Aoyama
Hiromitsu Aoyama
RIRui Ito
Rui Ito
YSYutaka Shimizu
Yutaka Shimizu
MAMitsuyuki Ashida
Mitsuyuki Ashida
TMToshiya Mitomo
Toshiya Mitomo
An exponentially Increasing number of wireless-LAN (WLAN) devices In a dense environment causes a decrease in throughput owing to collisions among the devices and the lack of contiguous bandwidth. The next-generation standard of 802.11ax improves spectrum efficiency by additionally supporting 1024 (1K) QAM, OFDMA with 80+80MHz; these impose several challenges to silicon design. 1K-QAM demands extreme IQ balance with an IRR better than -50dB over a wide frequency range up to 80MHz to achieve at least -35dB RX EVM or less. Noise characteristics better than -44dBc LO integrated phase noise as well as 50dB isolation between each TRX chain are mandatory. To best make use of the essential features defined in the 11ax standard, a real-time and arbitrary spectrum-resource control capability at each access point (AP) is beneficial both in terms of further improvement in spectrum efficiency as well as communication reliability in ISM coexisting bands and legacy WLAN. Interference identification of the order of 10με while incorporating everything into a strictly limited silicon area is key to launching the advanced unique functionality. This paper presents a fully integrated 4×4 802.11abgn/ac/ax-compliant AP transceiver SoC. The chip offers frequency-dependent IQ (FD-IQ) mismatch calibration for both amplitude and phase, low-noise TX BB and multimode LO distribution techniques, and real-time interference detection including 2.4GHz inverter-type microwave (MW) ovens.

1 December 2017
Verified
Conference Paper
Closed access
KNKensuke Nakanishi
Kensuke Nakanishi
HMHiroki Mori
Hiroki Mori
TKTakeshi Kumagaya
Takeshi Kumagaya
TATsuguhide Aoki
Tsuguhide Aoki
Inverter microwave ovens (MWOs) are day-to-day appliances that can act as fatal interferers for 2.4 GHz wireless LAN (WLAN) systems. However, the interference is avoidable, if it is possible to detect the MWO signal. In this paper, we propose an inverter MWO signal detection method in the time and frequency domains for reliable wireless communication. The operating inverter MWOs inherently generate RF signal whose leakage power level drastically varies depending on the switching of the inverter. The proposed method recognizes the changing signal power level due to the switching. In addition, we confirm the effectiveness of the proposed method in the presence or absence of WLAN systems by using the experimental MWO data obtained in a shielded room. It is revealed that the proposed method is able to detect the inverter MWO signal correctly and is robust against different products, different receiving environment, and presence of other signals.

21 May 2018 in IEEE Transactions on Cognitive Communications and Networking
Verified
Journal Article
Closed access
KNKensuke Nakanishi
Kensuke Nakanishi
HMHiroki Mori
Hiroki Mori
TKTakeshi Kumagaya
Takeshi Kumagaya
TATsuguhide Aoki
Tsuguhide Aoki
Inverter microwave ovens (inv. MWOs) are day-to-day appliances that can severely interfere with 2.4 GHz wireless LAN (WLAN) devices. However, interference is avoidable by using a signal detection method that recognizes MWO signals. In our previous work, we have proposed a specialized detection method that recognizes characteristic power levels of leakage signals from inv. MWOs, which drastically vary depending on the switching of the inverter. Using experimental MWO data obtained in a shielded room, we also demonstrated that the proposed method correctly detects inv. MWO signals with robustness against different products, different receiving environments, and the presence of other signals. In this paper, we begin with a discussion of the influence of MWO interference, and then review process and evaluation of the proposed method, along with new additional analysis. By simplifying the process, we also provide a test chip implementation for method realization and real-time signal detection to enhance the reliability of WLAN systems. Finally, we use the test chip to show that it is also possible to detect jammer signals.

23 August 2018 in EURASIP Journal on Wireless Communications and Networking
Verified
Journal Article
Open access
PDF file
KNKensuke Nakanishi
Kensuke Nakanishi
TNTeruhito Naka
Teruhito Naka
SHShinsuke Hara
Shinsuke Hara
TMTakahiro Matsuda
Takahiro Matsuda
KTKenichi Takizawa
Kenichi Takizawa
RMRyu Miura
Ryu Miura
Delay tomography is an inference technique for link delays in a network, where end-to-end route measurement is a promising method to reduce measurement overhead. Furthermore, by incorporating compressed sensing, delay tomography can efficiently detect sparse anomaly. In delay tomography, however, there is an inevitable issue that is clock synchronization for the route measurements. In this paper, based on route referencing, we study synchronization-free delay tomography with compressed sensing. From theoretical analysis, optimal route referencing and ordering methods for synchronization-free delay tomography are derived as “subtractive and differential schemes,” which cancel or minimize the error factors caused by clock asynchronism, clock skew, and normal link delays with single or multiple references, respectively. Simulation experiments confirm that the proposed methods can identify abnormal links more accurately with robustness against the error factors than a conventional scheme, where the newly proposed differential scheme always shows the best performance thanks to its better error factors cancelation.