Piezoelectric actuators are indispensable over a wide range of industries for their fast response and precise displacement. Most commercial piezoelectric actuators contain lead, posing environmental challenges. We show that a giant strain (1.05%) and a large-signal piezoelectric strain coefficient (2100 picometer/volt) are achieved in strontium (Sr)–doped (K,Na)NbO 3 lead-free piezoceramics, being synthesized by the conventional solid-state reaction method without any post treatment. The underlying mechanism responsible for the ultrahigh electrostrain is the interaction between defect dipoles and domain switching. The fatigue resistance, thermal stability, and strain value (0.25%) at 20 kilovolt/centimeter are comparable with or better than those of commercial Pb(Zr,Ti)O 3 -based ceramics, showing great potential for practical applications. This material may provide a lead-free alternative with a simple composition for piezoelectric actuators and a paradigm for the design of high-performance piezoelectrics.
Benefitting from the reversible phase transition between antiferroelectric and ferroelectric states, antiferroelectric materials have recently received widespread attentions for energy storage applications. Antiferroelectric configuration with specific antiparallel dipoles has been used to establish antiferroelectric theories and understand its characteristic behaviors. Here, we report that the so-called antiferroelectric (Pb,La)(Zr,Sn,Ti)O3 system is actually ferrielectric in nature. We demonstrate different ferrielectric configurations, which consists of ferroelectric ordering segments with either magnitude or angle modulation of dipoles. The ferrielectric configurations are mainly contributed from the coupling between A-cations and O-anions, and their displacement behavior is dependent largely on the chemical doping. Of particular significance is that the width and net polarization of ferroelectric ordering segments can be tailored by composition, which is linearly related to the key electrical characteristics, including switching field, remanent polarization and dielectric constant. These findings provide opportunities for comprehending structure-property correlation, developing antiferroelectric/ferrielectric theories and designing novel ferroic materials.
GeTe-based materials with superior thermoelectric properties promise great potential for waste heat recovery. However, the lack of appropriate diffusion barrier materials (DBMs) limits not only the energy conversion efficiency but also the service reliability of the thermoelectric devices. Here, we propose a design strategy based on phase equilibria diagrams from first-principles calculations and identify transition metal germanides (e.g., NiGe and FeGe 2 ) as the DBMs. Our validation experiment confirms the excellent chemical and mechanical stabilities of the interfaces between the germanides and GeTe. We also develop a process for scaling up the GeTe production. Combining with module geometry optimization, we fabricate an eight-pair module using mass-produced p-type Ge 0.89 Cu 0.06 Sb 0.08 Te and n-type Yb 0.3 Co 4 Sb 12 and achieve a record-high efficiency of 12% among all reported single-stage thermoelectric modules. Our work thus paves the way for waste heat recovery based on completely lead-free thermoelectric technology.
Phase boundary provides a fertile ground for exploring emergent phenomena and understanding order parameters couplings in condensed-matter physics. In Pb(Zr1-xTix)O3, there are two types of composition-dependent phase boundary with both technological and scientific importance, i.e. morphotropic phase boundary (MPB) separating polar regimes into different symmetry and ferroelectric/antiferroelectric (FE/AFE) phase boundary dividing polar and antipolar dipole configurations. In contrast with extensive studies on MPB, FE/AFE phase boundary is far less explored. Here, we apply atomic-scale imaging and Rietveld refinement to directly demonstrate the intermediate phase at FE/AFE phase boundary exhibits a rare multipolar Pb-cations ordering, i.e. coexistence of antipolar or polar displacement, which manifests itself in both periodically gradient lattice spacing and anomalous initial hysteresis loop. In-situ electron/neutron diffraction reveals that the same parent intermediate phase can transform into either FE or AFE state depending on suppression of antipolar or polar displacement, coupling with the evolution of long-/short-range oxygen octahedra tilts. First-principle calculations further show that the transition between AFE and FE phase can occur in a low-energy pathway via the intermediate phase. These findings enrich the structural understanding of FE/AFE phase boundary in perovskite oxides.
Deciphering the mechanisms governing photoinduced phase segregation in mixed halide perovskites is essential to unlock their full potential in stable, high-performance optoelectronic applications. We uncover the mechanism by which residual local strain acts as a key driving force of light-induced phase segregation. By combining in situ transmission electron microscopy with photoluminescence spectroscopy, we observe structural evolution and photocarrier behavior during phase segregation and after re-mixing. Although halide segregation is compositionally reversible, the perovskite lattice retains residual local strain, a “memory” of previously segregated halide domains, which evolves spatiotemporally with each phase segregation cycle. Residual local strain subsequently serves as a driver for successive phase segregation by trapping photocarriers and acts as the nucleation sites for iodide-rich domains. Our findings identify local strain as an intrinsic, evolving driving force of phase segregation, which offers a paradigm for improving the long-term stability of halide perovskites through strain management and compositional engineering.
The capacitors are in rising demand for cryogenic applications. As for now, it still remains an ongoing challenge for simultaneously achieving high energy storage density and cryogenic temperature stability. Herein, the strategy of stable backward phase transition was demonstrated in the antiferroelectric composition of (Pb0.9175La0.055)(Zr0.975Ti0.025)O3. As a result, we achieved high recoverable energy density about 10 J/cm3 with exceptional low-temperature stability from −160 to 25 °C. Multi-layer ceramic capacitors designed for pulse discharge applications also demonstrated high performance in cryogenic conditions, with the peak current fluctuations of less than 4%. Through in situ characterizations using x-ray diffraction, Raman spectra, and transmission electron microscopy, we discovered that the anisotropic structural evolution is responsible for a stable backward phase transition, providing the material with robust stability at cryogenic temperatures. These results offer a good paradigm for improving the temperature stability of antiferroelectric multi-layer capacitors to meet the rigorous demands of energy storage applications.