The spray pyrolysis technique has been extensively used to synthesize materials for a wide variety of applications such as micro and sub-micrometer dimension MOSFET´s for integrated circuits technology, light emitting devices for displays, and solid-state lighting, planar waveguides and other multilayer structure devices for photonics. This technique is an atmospheric pressure chemical synthesis of materials, in which a precursor solution of chemical compounds in the proper solvent is sprayed and converted into powders or films through a pyrolysis process. The most common ways to generate the aerosol for the spraying process are by pneumatic and ultrasonic systems. The synthesis parameters are usually optimized for the materials optical, structural, electric and mechanical characteristics required. There are several reviews of the research efforts in which spray pyrolysis and the processes involved have been described in detail. This review is intended to focus on research work developed with this technique in relation to high-K dielectric and luminescent materials in the form of coatings and powders as well as multiple layered structures.
The fabrication of NiO films by different routes is important to extend and improve their applications as hole-transporting layers in organic and inorganic optoelectronic devices. Here, an automated ultrasonic pyrolysis spray method was used to fabricate NiO and Li-doped NiO thin films using nickel acetylacetonate and lithium acetate dihydrate as metal precursor and dimethylformamide as solvent. The effect of the amount of lithium in the precursor solution on the structural, morphological, optical, and electrical properties were studied. XRD results reveal that all the samples are polycrystalline with cubic structure and crystallite sizes in the range of 21 to 25 nm, without any clear trend with the Li doping level. AFM analysis shows that the crystallites form round-shaped aggregates and all the films have low roughness. The optical transmittance of the films reaches values of 60% to 77% with tendency upward as Li content is increased. The electrical study shows that the films are p-type, with the carrier concentration, resistivity, and carrier mobility depending on the lithium doping. NiO:Li (10%) films were successfully incorporated into inorganic light emitting diodes together with Mn-doped ZnS and ZnO:Al films, all deposited on ITO by the same ultrasonic spray pyrolysis technique.
Composite scaffolds are commonly used strategies and materials employed to achieve similar analogs of bone tissue. This study aims to fabricate 10% wt polylactic acid (PLA) composite fiber scaffolds by the air-jet spinning technique (AJS) doped with 0.5 or 0.1 g of zirconium oxide nanoparticles (ZrO2) for guide bone tissue engineering. ZrO2 nanoparticles were obtained by the hydrothermal method and characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). SEM and fourier-transform infrared spectroscopy (FTIR) analyzed the synthesized PLA/ZrO2 fiber scaffolds. The in vitro biocompatibility and bioactivity of the PLA/ZrO2 were studied using human fetal osteoblast cells. Our results showed that the hydrothermal technique allowed ZrO2 nanoparticles to be obtained. SEM analysis showed that PLA/ZrO2 composite has a fiber diameter of 395 nm, and the FITR spectra confirmed that the scaffolds’ chemical characteristics are not affected by the synthesized technique. In vitro studies demonstrated that PLA/ZrO2 scaffolds increased cell adhesion, cellular proliferation, and biomineralization of osteoblasts. In conclusion, the PLA/ZrO2 scaffolds are bioactive, improve osteoblasts behavior, and can be used in tissue bone engineering applications.
ZrO2 and ZrO2: Al3+(× at.%) films were deposited by ultrasonic spray pyrolysis process. Luminescent films were produced from Oxychloride Zirconium Octahydrate and Aluminium Chloride Hexahydrate as precursors. Measurements of photo and cathodoluminescence were carried out doing variations on deposition temperature and doping concentration (× at.% Al3+ions). With the increase in substrate temperature, an overall growth of photo-cathodoluminescence intensities was perceived. Furthermore, these films presented luminescence concentration quenching with hight Al doping concentration. Chromaticity coordinates indicated blue emission from host lattice (ZrO2 films) and cold-white emissions from ZrO2: Al3+(× at.%) films. Closest CIE coordinates to the perfect white emission were x = 0.303, y = 0.337. XRD patterns, measured with variations of substrate temperature, showed tetragonal phase of nano-zirconium oxide films. In addition, surface morphology characteristics for studied films are presented.
Photoluminescent ZrO2 and ZrO2:Tb3+ thin films were synthesized from metal-organic precursor, zirconium acetylacetonate [Zr(C5H7O2)4], using Ultrasonic Spray Pyrolysis method. These thin films were deposited on Corning glass substrates at several deposition temperatures. ZrO2 and ZrO2:Tb3+ (X a/o) films were characterized by x-ray diffraction to identify the crystalline structure; results showed tetragonal phase of zirconia; with a crystalline size of approximately 4 nm according to Scherrer’s formula. Also, SEM micrographs revealed that surface morphology of these films is very flat. Chemical composition microanalysis showed presence of oxygen and zirconium as major species. Analysis by Infrared spectroscopy demonstrates that 900 and 760 nm bands correspond to presence of ZrO2. In addition, these films showed optical transmittances from 75 to 98 % in the visible range. Photoluminescent features varied as a function of excitation wavelength; when excited at λex = 286 nm strong green emission is observed, which is associated to electronic transitions 5D4 → 7Fn (n = 6, 5, 4, 3) corresponding to Tb3+ ions. Excitation with λex = 336 nm exhibits spectra with simultaneous emissions from host lattice and Tb3+ ions; here, observed color was blue-green.