There is a clear demand to increase detection depths in the context of raw material exploration programs. Semi-airborne electromagnetic (semi-AEM) methods can address these demands by combining the advantages of powerful transmitters deployed on the ground with efficient helicopter-borne mapping of the magnetic field response in the air. The penetration depth can exceed those of classic airborne EM systems because low frequencies and large transmitter-receiver offsets can be realized in practice. A novel system has been developed that combines high-moment horizontal electric bipole transmitters on the ground with low-noise three-axis induction coil magnetometers, a three-axis fluxgate magnetometer, and a laser gyro inertial measurement unit integrated within a helicopter-towed airborne platform. The attitude data are used to correct the time series for motional noise and subsequently to rotate into an earth-fixed reference frame. In a second processing step, and as opposed to existing semi-AEM systems, we transform the data into the frequency domain and estimate the complex-valued transfer functions between the received magnetic field components and the synchronously recorded injection current by regression analysis. This approach is similar to the procedure used in controlled-source EM. For typical source bipole moments of 20–40 kAm and for rectangular current waveforms with a fundamental frequency of approximately 10 Hz, we can estimate reliable three-component (3C) transfer functions in the frequency range from 10 to 5000 Hz over a measurement area of 4×5 km2 for a single source installation. The system has the potential to be used for focused exploration of deep targets.
The transition toward renewable energies demands a secure supply of critical raw materials and requires efficient noninvasive methods for deep earth resource exploration. The novel, deep electromagnetic (EM) sounding for the mineral exploration semi-airborne EM (semi-AEM) exploration concept aims at the efficient exploration of resources down to a depth of 1 km. Here, we evaluate a large-scale semi-AEM exploration study in a graphite mining district in eastern Bavaria, Germany. The derived 3D semi-AEM model is based on approximately 70,000 complex-valued data points recorded using seven transmitters. Strong conductivity contrasts with dominant east–west-trending anomalies are visible. Shallow high-conductivity structures correlate well with the known occurrence of graphite and match existing helicopter-borne EM results. The main anomaly reaches down to several hundred meters depth. To investigate different interpretation scenarios for large-scale semi-AEM data, we determine the effect of topography and analyze the feasibility of fast 2D inversion applications. To validate the robustness of the 3D semi-AEM model, the data set is inverted with two different 3D inversion algorithms and the results are compared. The presence of graphite leads to significant induced polarization (IP) effects with considerably high chargeabilities superposing EM induction. We include these effects in a realistic 3D inversion using a synthetic data study to analyze if the IP effect alters the overall conductivity structure and demonstrate that the obtained 3D model is reliable.
The classical radio-magnetotelluric (RMT) method is nowadays routinely applied to various environmental, engineering, and exploration problems. The technique uses radio transmitters broadcasting in the frequency range of 10 kHz to 1 MHz, and the measurements are carried out in the far field. The well-known disadvantages of RMT are a lack of robust radio transmitters in remote areas; the absence of transmitters broadcasting below 10 kHz, which limits the penetration depth; and a possible low signal-to-noise ratio. To overcome these difficulties, controlled sources can be used (controlled-source RMT [CSRMT]). We extend the CSRMT method to perform measurements not only in the far field but also in the transition zone. In CSRMT practice, it often is challenging to maintain far-field conditions for logistical reasons. Therefore, part of the measured data contains signatures of the source field, which cannot be interpreted with magnetotelluric software. In addition, the source placed directly in the survey area allows us to increase the signal-to-noise ratio and resolution. Such CSRMT in the transition zone is, in fact, a controlled-source electromagnetic method but with full impedance tensor and tipper vector transfer functions. We develop new procedures for the 3D modeling and inversion of the tensor radio-frequency data measured in the transition zone of two perpendicular horizontal electric dipole sources. In this case, the geometry of the source must be considered in the forward modeling. The developed modeling and inversion software is tested on a synthetic 3D model. The 3D resistivity models derived from the real data confirm the geologic settings and are consistent with the available borehole information. Therefore, we conclude that the CSRMT approach extended to include the source field is feasible and that the developed procedures are reliable.
We have developed a transient electromagnetic (TEM) study in the noisy urban environment of the megacity Santiago de Chile. Our investigation characterizes the electrical conductivity structure of the Santiago Basin down to 300 m depth, providing key information about the sedimentary infill, hydrogeologic aspects, and geomorphological units. In total, 52 TEM soundings were recorded over roughly 900 km2. We identified different transient characteristics and noise patterns, spatially correlated to the investigation area. This step allowed classification of the soundings into three groups: highly distorted data, transients severely affected by cultural electromagnetic noise sources, and good-quality data with low noise levels. Conventional 1D inversion techniques were then used to derive resistivity depth models. The models were interpreted using sedimentary units, alluvial fan, static groundwater level information, and also were verified using borehole data. Based on 1D models, different minimum sedimentary thicknesses are observed, ranging between 50 and 300 m in depth. The average derived sedimentary thickness is approximately 210 m. In addition, seven soundings indicated the basement. These are mostly located toward the periphery of the Santiago Basin. We found a high conductive zone toward the north and a low-conductive area toward the south of the basin. The southern area is characterized by the absence of conductive layers at a depth between 100 and 150 m. This is likely related to the presence of a thick gravel layer and the absence of shallow clay layers acting as aquitards. The resistivity distribution and the sedimentary thickness obtained for this noisy and urban environment are key inputs for groundwater research as the water supply becomes more limited, specifically in central Chile. The overall consistency of the derived subsurface models highlights the suitability of the TEM method for investigating urban noise environments.
The shift toward renewable energy sources necessitates a stable supply of essential raw materials and calls for advanced, noninvasive techniques to explore deep-seated mineral resources. In the past few years, the semi-airborne electromagnetic (SAEM) method has been further developed to efficiently investigate the subsurface down to 1 km depth. The Kropfmühl graphite deposit in Lower Bavaria comprises high-grade metamorphic graphite-bearing gneisses. Although mining reaches depths of 200 m, the western extent of the deposit remains unknown. To verify the western extension and continuity of the Kropfmühl graphite deposit, a drone-based SAEM survey was conducted, combining a dense spatial sampling of magnetic fields using a UAV (Unmanned Aerial Vehicle) system and a high signal strength with controlled-source electromagnetic transmitters on the ground. The survey area spanned approximately 1.8 × 2.5 km2, using four galvanically coupled dipole transmitters and multiple UAV flights over 4 days. To increase depth sensitivity, a total-field magnetometer alongside a three-component induction coil system was used. To derive a reliable subsurface conductivity model, a 3D inversion of multifrequency, multisource SAEM data from vector and scalar magnetic field data was conducted. The obtained model revealed three east–west trending conductive anomalies, interpreted as graphite-rich zones. The main anomaly (C1), 200 m south of the active mine, indicates possible fault-controlled displacement. Borehole resistivity logs and available helicopter-borne electromagnetic data correlate well with conductive zones and graphite enrichment. The results highlight the potential of UAV-based SAEM to image complex subsurface structures. The method delivers high-resolution, cost-effective data acquisition, with a high data coverage and only the transmitters requiring ground installation. This renders the method suitable for imaging geologically complex settings in hard-to-access areas.
14 October 2024 in IEEE Journal of Selected Topics in Applied Earth Observations and Remote Sensing
Different electromagnetic (EM) techniques have distinct resolutions for the exploration of natural resources. Integrating independent information from different EM datasets in a joint inversion results in a more precise and reliable resistivity model. To conduct an efficient joint inversion, it is crucial to understand the resolution characteristics of each EM technique and configuration. To enhance the interpretation using 1-D joint inversion of multiple EM datasets in a former mining area in eastern Thuringia (Germany), we developed a novel workflow for systematic resolution studies. Rather than focusing on limited resistivity models, our approach provides a broader perspective on the resolution characteristics of specific EM methods. The workflow is applied to helicopter-borne EM (HEM), semi-airborne EM (Semi-AEM), and long-offset transient EM datasets. Resolution studies reveal not only the advantages and limitations of each method but also demonstrate scenarios where joint inversion benefits. These insights are useful to optimally design multimethod applications. A synthetic 1-D joint inversion example successfully reconstructs the true model, while each individual method fails. This example demonstrates the added value of our presented resolution study workflow with respect to experimental design and acquiring optimal data in terms of resolution capabilities. We provide a toolkit for resolution analysis that serves as a roadmap for multimethod studies. Subsequently, we demonstrate that the accurate determination of shallow layers improves the resolution for deep targets. This is significant for designing deep exploration prospects. In the last step, our novel triple-method joint inversion scheme is validated through the application of field data.