9 February 2023 in IEEE Transactions on Power Electronics
The development of wide band-gap power electronics over the last two decades has stimulated a tremendous amount of research into high performance liquid cooling solutions for high heat flux (200-1000 W/cm $^{2}$ ) power semiconductor devices. A patent literature search for electronics cooling technologies was conducted in the late-2000 time frame and promising technologies for high performance thermal management were identified, at that time, for research and development. These promising technologies were separated into four categories classified as single-phase (i.e., liquid) jet impingement cooling, microchannel cooling, phase change or two-phase cooling, and near-junction including direct chip cooling. In this Letter, a perspective is provided on select patents from our group that stem from research into these technology areas from 2010 to 2022. Additionally, the thermal-fluid performance capability of each technology is briefly summarized. As a whole, the Letter provides a demonstration of the historical significance of power electronics cooling technology on the mobility industry and briefly outlines future directions for research and development.
22 August 2019 in IEEE Transactions on Power Electronics
This paper $^1$ proposes an unsupervised learning approach for fault prognosis of Silicon Carbide (SiC) MOSFETs. The proposed approach utilizes the changing trend of a device's voltage, current, temperature and other device characteristics with its degradation. The failure modes of semiconductors are reviewed along with existing methods for fault prognosis. The proposed approach is the first to address prognostics of SiC devices, and it can avoid the effects from system noise and data errors. It is not limited to offline analysis and is targeted at online implementation. It is easy to implement on standard digital platforms, and has fast computational speed. Offline data analysis is performed to verify the effectiveness of the proposed method, and a processor-in-the-loop system is used to verify its ability to perform online fault prognosis.
7 January 2022 in IEEE Transactions on Power Electronics
Power electronics (PE) and high-frequency switching circuits are key to superior performance of electric vehicles. It is vital to monitor the condition of the PE components in real-time for safety and reliability. In this article, we propose two anomaly detection methods based on a combination of data preprocessing to suppress noise and outliers, multivariate regression models to predict signals of interest under nominal operation, and sequential analysis of residuals. In particular, the methods utilize median filtering to extract on -state medians in each switching cycle in nonlinear autoregressive exogenous neural network models or filtered on -state data in partial least squares-based models to represent the nominal circuit behavior. Optimal and approximate dynamic programming-based feature selection methods are developed to select the most informative signals or their transformations. Predictions from the learned models are used to generate the residuals for anomaly detection by Page’s cumulative sum test. The proposed models and anomaly detection methods are validated on three accelerated aging experimental datasets, comprised of 60 power mosfet devices with low-frequency and high-frequency switching under disparate operating conditions. Due to the simplicity and efficiency of the data-driven anomaly detection schemes, the proposed methods can potentially be embedded in real-time digital platforms.
15 January 2024 in International Journal of Heat and Mass Transfer
19 September 2019 in Journal of Electronic Packaging
This paper demonstrates the concept and fabrication process for a novel (copper, nickel)–tin, (Cu, Ni)–Sn, transient liquid phase (TLP) high-temperature bond that exploits the addition of a pure aluminum (Al) core layer for die attachment in a power electronics power card structure. The bond quality and composition of the bond layer are characterized using confocal scanning acoustic microscopy (CSAM), scanning electron microscopy (SEM), and energy-dispersive X-ray (EDX). The experimental results indicate that the material composition and established fabrication process enable a crack-free bond that exhibits a void fraction of 2% or less. Compared to a traditional foil-based single-layer TLP bonding system, the proposed foil-based TLP/metal laminated structure displays ∼60% reduction in thermally induced mechanical stress built-in after fabrication, as verified through steady-state thermal stress simulations.
7 September 2019 in Journal of Thermal Science and Engineering Applications
The heat transfer and fluid flow performance of a hybrid jet plus multi-pass microchannel heat sink in two-phase operation is evaluated for the cooling of a single large area, 3.61 cm2, heat source. The two-layer branching microchannel heat sink is evaluated using HFE-7100 as the coolant at three inlet volumetric flow rates of 150, 300, and 450 ml/min. The boiling performance is highest for the flow rate of 450 ml/min with the maximum heat flux value of 174 W/cm2. Critical heat flux was observed at two of the tested flow rates, 150 and 300 ml/min, before reaching the maximum operating temperature for the serpentine heater. At 450 ml/min, the heater reached the maximum allowable temperature prior to observing CHF. The maximum pressure drop for the heat sink is 34.1 kPa at a heat flux of 164 W/cm2. Further, the peak heat transfer coefficient value of the heat sink is 28,700 W/m2K at a heat flux value of 174 W/cm2 and a flow rate of 450 ml/min. Finally, a validated correlation of the single device cooler is presented that predicts heat transfer performance and can be utilized in the design of multi-device coolers.