19 January 2018 in Advanced Materials
18 April 2017 in Journal of Applied Physics
ZnO is considered as one of the most promising semiconductor materials for future applications based on the piezotronic effect. Intense studies on ZnO nanowires had been carried out to understand the modulation of the Schottky barrier height at the metal ZnO interface via piezoelectricity. However, an experimental investigation on bulk ZnO single crystals and a fundamental comparison of the modification of the barrier height determined experimentally and theoretically are still missing. Therefore, an adjustment of the electrostatic potential barrier height at metal-ZnO single crystal interfaces due to stress induced piezoelectric charges was conducted, using both O- and Zn-terminated surfaces. In-situ stress dependent impedance and current-voltage measurements were utilized to extract the electrical properties of the potential barrier and to determine the reduction of the barrier height. The decrease of the interface resistance and increase of the capacitance reveal the presence of stress induced piezoelectric charges. The experimentally evaluated reduction of the barrier height reveals a moderate change of about 9 meV at 70 MPa and supports prior work on metal-ZnO nanowires. This change was found to be in good agreement with theoretical calculations based on the imperfect screening model if a thickness of the interface layer is assumed to be ∼2 .
30 September 2018 in Journal of the American Ceramic Society
16 January 2020 in Journal of Applied Physics
Mechanically induced changes in electrical properties have gained increasing interest over the last decade. The research field piezotronics, which describes the change in potential barrier height (e.g., at Schottky contacts) by piezoelectric charges, could lead to promising applications such as sensors or strain trigged transistors. In this contribution, the changes of potential barriers by mechanical stress at several grain boundaries of polycrystalline ZnO have been quantified. Rationalization is provided by concurrent measurement of crystal orientations of both neighboring grains. The highest changes in barrier height could be observed at ZnO–ZnO grain boundaries exhibiting varistor properties. In this case, the barrier height can be almost completely reduced by positive piezoelectric charges. Furthermore, an increase in barrier height is observed with negative piezoelectric charges. The developed physical model suggests an equivalent impact of externally applied voltage and induced positive piezoelectric charge on the barrier properties. In turn, not only the barrier height is modified by piezoelectric charges but also the breakdown voltage. This has, nevertheless, been only indirectly verified in experiments. These allow rationalizing the proposed model. Furthermore, a statistical study reveals a change in the distribution of breakdown voltages with changing stress conditions in the varistor ceramic.
14 November 2019 in Journal of the American Ceramic Society
TEM and SEM investigations of ZnO bicrystal interfaces were undertaken with an aim to study the correlation of local grain‐boundary structure, segregation and electrical transport perpendicular to the interface. To this end, varistor‐like ZnO bicrystals with piezotronic characteristics were chosen with (0001̅)║(0001̅) tail‐to‐tail orientation with respect to the c‐axis. In order to contrast different local grain‐boundary structures with different coherency and segregation of bismuth, but identical macroscopic polarization state, two complementary processing techniques were applied. A diffusion‐bonded bicrystal with an intermediate thin film containing Zn‐Bi‐Co‐O provided a straight interface as reference. In contrast, a ZnO bicrystal prepared by epitaxial solid‐state transformation was manufactured by bonding two ZnO single crystals with a 100 µm thick polycrystalline ZnO varistor material with a typical dopant composition including bismuth and cobalt. This structure was annealed to the point that a bicrystal was formed with the varistor concentration at the boundary, which was strongly curved due to the polycrystalline microstructure still providing a shadow image at the interface. The results highlight a distinct correlation between local interfacial morphology, degree of segregation of bismuth and degree of nonlinearity of the electrical transport across the interface.
1 November 2018 in AIP Advances
An extended phenomenological model is proposed to rationalize the potential barriers of the varistor like boundaries of piezoelectric semiconductors. This model takes self-consistently into account the inverse piezoelectric effect of the internal electric field associated with the barrier height at grain boundaries. A double Schottky barrier at a grain boundary gives rise to a strong internal electric field in the depletion layer. Due to the inverse piezoelectric effect, this internal electric field leads to mechanical strain and consequently piezoelectric charge at a grain boundary and also an additional space charge associated with the polarization inhomogeneity. The piezoelectric charges in return impacts the barrier height. Results show that the piezoelectric charge induced by the internal field tends to adjust the grain boundary charge and lowers the barrier height. Furthermore, the barrier height becomes less sensitive to mechanical stress and applied voltage if the influence of the internal field is taken into account. The extended model with the inverse piezoelectric effect of the internal field allows to further elucidate their piezotronic response. The work improves the grain boundary barrier height theory of piezoelectric ceramics and is expected to have general impact on piezotronics and other junction devices.