Vitaliy Kononov

Vitaliy Kononov

Auto-generated profile, based on publicly available information

Vitaliy Kononov

Національний університет «Запорізька політехніка», м. Запоріжжя

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
26 March 2025 in New Materials and Technologies in Metallurgy and Mechanical Engineering
Verified
Journal Article
Open access
PDF file
SBSergiy Byelikov
Sergiy Byelikov
ВКВіталій Кононов
Віталій Кононов
OHOleksandr Hlotka
Oleksandr Hlotka
VVValeriy Vinichenko
Valeriy Vinichenko
YMYuriy Mykhaylov
Yuriy Mykhaylov
ІМІгор Макаров
Ігор Макаров
Purpose The main objective of the work was to study the influence of the working environment on the performance of the ГТК-10I hollow working blades. Research methods. Microstructure studies were carried out on microsections under a “Neophot-2” microscope and a “Stereoscan” microscope-analyzer. Microhardness was measured with a ПМТ-5 device. Phase composition and lattice periods of the main components were measured on a ДРОН-1 diffractometer in copper Kα radiation. The content of chemical elements was measured on a REM-106I scanning electron microscope. Short-term strength tests (GOST 1497-61, GOST 9651-61, GOST 1497-84) were carried out on standard cylindrical samples (diameter of the working part 5 mm, length 25 mm) at temperatures of 200, 800, 900 and 10000°C on a УМЕ-10TM tensile machine. Long-term strength tests (GOST 10145-81) were performed on standard cylindrical samples at temperatures of 800, 900, 10000°C and corresponding loads of 600, 400, 180 MPa on the AIMA-5-2 machine by uniaxial stretching of samples under constant load. Comparative experimental studies of high-temperature corrosion of alloys were carried out in synthetic ash using a method widely used in the industry. For corrosion tests, standard cylindrical samples (diameter 10 mm, length l = 12 mm) were used, on which, after preliminary degreasing, measurement and weighing on an analytical balance with an accuracy of (± 0.0005 g), synthetic ash in an amount of 12 mg / cm2 was applied to their surface, simulating the combustion products of gas turbine fuel of the following composition, which were placed and kept in a furnace on a platform made of refractory material in an air atmosphere. Obtained results. Studies of the influence of the working environment on the performance of the ГТК-10I hollow blades. It is shown that the working environment significantly affects the performance of the ГТК-10I hollow blades. It was established that the outer layer of the profile part did not show deep damage due to their removal by a high-speed gas flow. It was established that corrosion damage begins from the beginning of operation and the damaged layer contains sulfides of the TiS and Ti2S3 types. It is shown that the short-term strength of the ЗМІ-3 alloy relative to the initial values (passport data) decreases by approximately 16–20 %. It was established that due to structural changes in the alloy during operation, the time to fracture of the samples under load decreased by approximately 18–22 %. Based on the studies performed, the use of protective coatings is necessary to increase performance. Scientific novelty. Obtained results make it possible to evaluate the processes that occur during operation on the surface of products and to establish relationships between alloying elements concentration and the corrosion rate. Practical value. Obtained results allow us to recommend domestic alloys as a substitute for foreign alloys without losing the properties and durability of the products.

20 April 2023 in New Materials and Technologies in Metallurgy and Mechanical Engineering
Verified
Journal Article
Open access
PDF file
AGAlexander Glotka
Alexander Glotka
VOV. Ol’shanetskii
V. Ol’shanetskii
SBS. Byelikov
S. Byelikov
ВКВ. В. Кононов
В. В. Кононов
ВХВ. В. Хвостак
В. В. Хвостак
Мета роботи. Полягає у встановленні закономірностей впливу легувальних елементів на теплофізичні характеристики жароміцних нікелевих сплавів рівноосної кристалізації, що дозволяє оптимізувати процеси виготовлення та термічного оброблення. Методи дослідження. Експериментальні значення оброблялися математичними методами з отриманням кореляційних залежностей типу «параметр-властивість», що оптимально їх описують. Для експериментально-теоретичних досліджень температурної здатності сформовано робочу вибірку сплавів, що складається з відомих промислових жароміцних нікелевих сплавів для рівноосного лиття вітчизняного та закордонного виробництва. Отримані результати. Встановлено закономірності впливу хімічного складу жароміцних нікелевих сплавів рівноосної кристалізації на теплофізичні характеристики. Отримані співвідношення, що дозволяють врахувати критерії конкуренції (кооперації) хімічних елементів та отримати діаграми, за допомогою яких можна визначити критичні температури. Наукова новизна. Раніше отримані і нові співвідношення Кg¢, Кg, КМС та КМ23С6 дозволяють врахувати критерії конкуренції (кооперації) хімічних елементів у складі жароміцних нікелевих сплавів рівноосної кристалізації. Завдяки цим співвідношенням отримана діаграма, за допомогою якої можна встановити теплофізичні характеристики жароміцних сплавів. Практична цінність. Запропоновані ефективні рішення по встановленню основних критичних температур жароміцних сплавів рівноосної кристалізації, що дало змогу оптимізувати температури виробництва, термічної обробки та експлуатації. Отримані розрахункові значення критичних температур мали задовільну збіжність з результатами отриманими диференціально-термічним аналізом.

1 November 2025 in Journal of Achievements in Materials and Manufacturing Engineering
Verified
Journal Article
Closed access
OGO. Glotka
O. Glotka
VKV. Kononov
V. Kononov
YFYelyzaveta Fasol
Yelyzaveta Fasol
The purpose is to establish dependencies between chemical and phase composition in the Ni-Al-Cr-Co-W-Mo-Ti-Nb-Ce-Zr-B-La system; obtain dependencies between the mismatch of crystal lattices of the strengthening phase and matrix; obtain dependencies between phase composition and mechanical properties to increase the service life of hot-tract parts.The methodology for obtaining the dependencies involved simulating the thermodynamic processes of phase formation, where the elements were changed step by step using the CALPHAD thermodynamic modelling method. Predictive calculations were performed based on the initial chemical composition of the VZhL-12 alloy, which determined the most probable phases and their corresponding chemical compositions. The phase composition was experimentally determined using a REM-106I scanning electron microscope with an energy-dispersive X-ray spectral microanalysis system. The method was employed to investigate the morphology and chemical composition of the precipitated phases within the alloy structure.The influence of individual alloying elements on phase stability has been established: aluminium promotes the formation of the γ′-phase, reaching its content of up to 89% at 7.6% Al, but when in excess, it causes the formation of brittle TСР phases, which impair ductility; titanium also increases the content of the γ′-phase, but when the content is above 6.4%, it leads to the formation of lamellar TСP phases (for example, the η-phase), which negatively affect the mechanical properties; cobalt and chromium increase their concentration in the strengthening phase, promoting its thermal stability. Molybdenum and tungsten do not directly participate in the formation of the γ′-phase but increase its heat resistance. The effect of temperature on the lattice parameters of the γ and γ′-phases is shown. The minimum mismatch of the lattice parameters (-0.4%) is observed at 700-800C, corresponding to optimal values of strength, ductility, and creep resistance. Experimental testing on the industrial single-crystal alloy VZhL-12 yielded good agreement between the calculated and actual data.The established patterns of alloying, phase transformations, and thermomechanical properties can serve as the basis for creating new generations of materials capable of operating under extremely high temperatures and loads. However, the disadvantages of this method include sensitivity to the initial data, the ability to analyse materials only in a stable state, and the reliability of thermodynamic databases (which have recently improved significantly). Future studies are planned to study the behaviour of secondary phases and the influence of rare earth elements in the system.The obtained relationships between alloying, phase transformations and thermomechanical properties can be used to create new generations of materials. They enable the determination of properties of new alloys without testing, significantly reducing research costs. The work will also be beneficial in refining the existing chemical compositions of alloys.The work is intended for researchers and engineers in the field of high-temperature materials (superalloys).

30 October 2024 in New Materials and Technologies in Metallurgy and Mechanical Engineering
Verified
Journal Article
Open access
PDF file
КОК. В. Обносов
К. В. Обносов
VSVadym Shalomeev
Vadym Shalomeev
OHO. Hlotka
O. Hlotka
ВКВ. В. Кононов
В. В. Кононов
YFYelyzaveta Fasol
Yelyzaveta Fasol
ЄФЄ. О. Фасоль
Є. О. Фасоль
Purpose. Establishing the specifics of the influence of alloying elements on the formation of carbides in the structure, their shape and the possibility of separating TLC phases for the system of the Ni-Cr-Co-W-Mo-Al-Ti-C type using the CALPHAD calculation method of prediction in comparison with data obtained by the method of raster electron microscopy. Research methods. The results of experimental and calculated data, formed on the basis of experimental and results taken from open sources, are presented. The chemical composition was determined on a REM-106I scanning electron microscope equipped with an energy dispersive analysis. Experimental values were processed by the method of least squares with obtaining correlation dependencies of the “parameter-property” type and establishing mathematical equations of regression models that optimally describe these dependencies. Results. It was established that when the concentration of titanium is more than 4 % and molybdenum is more than 6 % and 15 % chromium, the formation of TSC phases (Р, s and m- phases) is possible, which reduce the operational properties of the alloy. It was found that when the alloy contains more than 25 % chromium, a solid chromium-based solution is formed, which reduces the properties of the alloy (mechanical and corrosion). It is shown that the obtained dependences correspond to reality and coincide with experimental data at the level of 10 %. Scientific novelty. Obtained dependences of the influence of alloying elements on the chemical composition of carbides will allow predicting properties without conducting experiments. It was established that changes in the course of dependencies are closely correlated with the processes occurring in the structure of alloys. Practical value. The obtained dependencies can be used both for the development of new heat-resistant alloys and for the improvement of the compositions of industrial alloys.

16 June 2025 in New Materials and Technologies in Metallurgy and Mechanical Engineering
Verified
Journal Article
Open access
PDF file
MSMykhailo Sydorenko
Mykhailo Sydorenko
VKVitaliy Kononov
Vitaliy Kononov
EKEvhen Kravchenko
Evhen Kravchenko
МСМихайло Сидоренко
Михайло Сидоренко
ЄКЄвген Кравченко
Євген Кравченко
Purpose. To enhance the load-bearing capacity of the junction nodes between main and end beams of overhead cranes by improving diagnostic methodologies and developing structural reinforcement techniques for repair applications. Research methods. The stress state of junction nodes was investigated using the finite element method with adaptation of the hot spot stress approach to Ukrainian standards. Stress-strain analysis of the overlapping structure was conducted using sub-modeling techniques. Stress intensity factors were determined through the displacement method. Results. Based on statistical data analysis, a logit model was developed to determine the probability of junction node damage depending on overhead crane parameters. It was established that for butt joint structures, the most significant factors are operation intensity (coefficient 4.0) and service life (coefficient 2.05), whereas for overlapping structures, operation intensity is the dominant factor (coefficient 6.12). Stress state models were developed for nodes under vertical and transverse loads. It was discovered that increasing the gusset plate leg length does not have the expected effect on stress magnitude due to load redistribution between end beam elements. It was determined that reinforcing end beam webs can reduce stresses in the upper flange by a factor of 1.8. Structural methods for enhancing the load-bearing capacity of butt joint and overlapping structures were proposed. Experimental verification confirmed that when using an integrated approach (gusset plate, overlay, and cut-out) for overlapping structures, the maximum effective stresses in the cut-out zone are 60 MPa. Scientific novelty. New data were obtained regarding the influence patterns of structural parameters of junction nodes between main and end beams of overhead cranes on their load-bearing capacity. Relationships between crack length and fracture toughness parameters were established, enabling prediction of the residual service life of junction nodes. Practical value. The developed structural methods for enhancing the load-bearing capacity of junction nodes provide sufficient safety margins against high-cycle fatigue and improve the operational safety of overhead cranes.

25 March 2025 in New Materials and Technologies in Metallurgy and Mechanical Engineering
Verified
Journal Article
Open access
PDF file
SBSergiy Byelikov
Sergiy Byelikov
ВКВіталій Кононов
Віталій Кононов
OHOlexandr Hlotka
Olexandr Hlotka
MSMichael Sydorenko
Michael Sydorenko
SPSergiy Pychek
Sergiy Pychek
СПСергій Пучек
Сергій Пучек
Purpose. To conduct comparative studies of the complex of physico-mechanical properties of the imported alloy N-155 and the domestic alloy ЗМІ-11 in order to increase the service life of the rotating blades. To conduct comparative tests on the short-term and long-term strength of the alloys in the initial state (after heat treatment), to conduct comparative tests on the short-term and long-term strength of the alloys after prolonged thermal action at T = 850 °C, 950 °C for 1000, 3000, 5000 hours and to conduct research by metallographic method and micro-X-ray spectral analysis of the microstructure and phase composition of the alloys. Research methods. Alloy samples were made from ingots weighing 10 kg in a vacuum induction furnace УППФ-3M in an argon environment at a pressure of 1.4–5.3 Pa in crucibles with the main lining with simultaneous pouring of samples of equiaxed crystallization. Chemical analysis was carried out by standard methods in accordance with the requirements of TU 14-1689-73 and OST 1.90127-85. Microstructure studies were carried out on microsections, the plane of which was oriented normal to the surface on a light optical microscope “Olympus IX-70” with a digital video camera “ExwaveHAD color video camera Digital Sony” at magnifications ×200, ×500, ×1000. Strength tests (GOST 1497-61, GOST 9651-61, GOST 1497-84) were carried out on standard cylindrical samples (diameter of the working part 5 mm, length 25 mm) at temperatures 200, 800, 900 and 1000°C on a УМЕ-10TM brand tensile machine. Long-term strength tests (GOST 10145-81) were carried out on standard cylindrical samples at temperatures 800, 900, 10000 °C and corresponding loads 600, 400, 180 MPa on an AIMA-5-2 machine. Obtained results. It was found that during tests at 800 and 900°С, the tensile strength of the N-155 alloy is 1.2 times lower than that of ЗМІ-11, and the long-term strength is 5.2 times lower, respectively. It was shown that the amount of the strengthening phase in the ЗМІ-11 alloy is 6…10 % more, evenly distributed throughout the alloy body. It was established that in the composition of the strengthening phase of the ЗМІ-11 alloy, the concentration of chromium, tungsten, and molybdenum remains practically unchanged and does not depend on the presence of niobium. At the same time, in the composition of the strengthening phase of the ЗМІ-11 alloy, the concentration of cobalt increases by 1.4 times, and the concentration of aluminum and titanium decreases by 1.1 times compared to the N-155 alloy. It was established that in the process of dissolving non-equilibrium eutectic precipitates, microvolumes arise, locally supersaturated with tungsten, chromium, and titanium, in which the probability of the formation of carbides on a more complex basis increases. It was found that during prolonged thermal action carbides based on tantalum TaC and on a mixed basis (Ta, Ti) C in the ЗМІ-11 alloy are thermally more stable than carbides in the N-155 alloy. Scientific novelty. The obtained results allow us to understand the thermodynamics of phase formation processes in two alloying systems and to establish the relationships between alloying elements concentration and the phase composition of the alloy. Practical value. The obtained results allow us to recommend the domestic ЗМІ-11 as a substitute for the foreign alloy N-155 without loss of properties and service life.