Serhii Puchek

Serhii Puchek

Auto-generated profile, based on publicly available information

Serhii Puchek

National University "Zaporizhzhia Polytechnic" (Zaporizhzhia, Ukraine)

Research Focus & Metrics

Academic Career Length

2Years (2025-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
31 March 2026 in New Materials and Technologies in Metallurgy and Mechanical Engineering
Verified
Journal Article
Open access
SPSerhii Puchek
Serhii Puchek
SBSergiy Byelikov
Sergiy Byelikov
Purpose. To study the macro- and microstructural state of pilot heat-resistant alloy ZhS32-VI casts for the production of critical gas turbine engine components and to evaluate their mechanical properties and heat resistance. Research methods. Structural stability parameters were assessed using the well-known PHACOMP and New PHACOMP calculation methods. Macro- and microstructural analysis and phase composition studies were performed using optical metallography. Mechanical properties at room temperature were determined in accordance with ISO 6892-84 and ST SEV 471-88, while creep-rupture strength tests were conducted in accordance with DSTU ISO 204:2019. Results. The structure and properties of ZhS32-VI alloy specimens produced in a ULMAC FM 1-2-100 vacuum furnace using equiaxed crystallization were studied. The microstructure of the specimens before heat treatment corresponded to the as-cast state of the alloy, and after heat treatment, it met the technical specifications and conformed to the approved microstructure scale. Mechanical properties and heat resistance meet the requirements of technical documentation for critical heat-resistant castings. Scientific novelty. New data on the structure and phase composition of the heat-resistant alloy ZhS32-VI alloy from pilot heats were obtained. Calculation and analytical evaluation method confirmed a high level of structural stability. Practical value. The obtained results provide an opportunity to expand the application of the ZhS32-VI heat-resistant nickel alloy for the production of critical castings.

23 December 2025 in New Materials and Technologies in Metallurgy and Mechanical Engineering
Verified
Journal Article
Open access
SPSerhii Puchek
Serhii Puchek
SBSergiy Byelikov
Sergiy Byelikov
Purpose. To study the macro- and microstructural state of a series of research samples of the heat-resistant alloy ZhS26-VI for the production of critical components of a gas turbine engine, namely rotor blades of a high-pressure turbine (HPT), and to evaluate the mechanical properties and heat resistance in accordance with the technical specifications of the materials of the gas turbine hot part . Research methods. Macro- and microstructural analysis and phase composition studies were carried out by optical metallography using an optical microscope. Mechanical properties at room temperature were determined in accordance with ISO 6892-84 and ST SEV 471-88. Tensile tests were carried out on a ZDMY30 machine. Results. The structure and properties of samples of experimental melts of the ZhS-26VI alloy obtained in the FM-1-2-100 vacuum furnace of the “ULMAC” company by the method of equiaxed crystallization were studied. Significant grinding of the macrograin was established due to intensive heat removal and high crystallization rate. The microstructure of the samples before heat treatment corresponds to the cast state of the alloy, and after heat treatment in the standard mode satisfies the technical conditions and corresponds to the approved microstructure scale. The mechanical and heat-resistant properties of the samples meet the requirements of the regulatory documentation for responsible heat-resistant casting. Scientific novelty. New data on the structure and phase state of the ZhS26-VI alloy of experimental and serial melts were obtained. The fine structure of the nickel-based heat-resistant alloy, which is traditionally used to produce high-pressure turbine blades of an aviation gas turbine engine, was studied. Practical value. The results obtained provide an opportunity to expand the use of the ZhS26-VI heat-resistant alloy for the production of castings for critical purposes.

7 September 2026 in Casting Processes
Verified
Journal Article
Open access
PDF file
SPSergey Puchek
Sergey Puchek
SBSergey Belikov
Sergey Belikov
The structures and properties of the working blades of the first stage of aircraft gas turbine engines (GTD), cast from the heat-resistant nickel alloy ZhS32-VI by the method of high-speed directional crystallization after hot isostatic pressing (HIP) and various heat treatment regimes. HIP at a temperature of 1250 ℃ and a pressure of 170 MPa contributes to the improvement of the quality of castings by stabilizing the structure and properties due to the reduction of microporosity during the "healing" of pores. The size of individual micropores detected after HIP is approximately 32 times smaller compared to the pores observed in the blades before the HIP operation. As a result of plastic deformation initiated by HIP, the formation of a "raft" structure in the form of zonal areas concentrated in the places of "healing" of pores, as well as the release of coagulated phase particles, which together with lamellar (eutectic) carbides have the appearance of a framework. Heat treatment according to the standard regime (1270 ℃, 1h.15min) after HIP promotes recrystallization of the strengthening phase, increases the structural homogeneity of the alloy and causes relaxation of stresses induced in the HIP process, which positively affects the physical and mechanical properties. Four-hour heat treatment at a temperature of 1050 ℃ immediately after the HIP operation does not eliminate structural heterogeneity, which is characterized by the presence of liquation zones, as well as areas characteristic of "raft" - structures formed during the gas-setting process. Conducting intermediate high-temperature heating (homogenization) after HIP at a temperature of 1270℃ (1h.15min) with subsequent heating at a temperature of 1050℃ for 4 hours contributes to obtaining a more homogeneous structure of the ZhS32-VI alloy, which positively affects the mechanical and heat-resistant properties. Досліджено структури та властивості робочих лопаток І ступеня авіаційних газотурбінних двигунів (ГТД), відлитих із жароміцного нікелевого сплаву ЖС32-ВІ методом високошвидкісної спрямованої кристалізації (ВСК) після гарячого ізостатичного пресування (далі — ГІП) та різних режимів термічної обробки. ГІП при температурі 1250 ℃ і тиску 170 МПа сприяє підвищенню якості виливків за рахунок стабілізації структури та властивостей унаслідок зменшення мікропористості при «заліковуванні» пор. Розмір виявлених після ГІП поодиноких мікропор приблизно у 32 рази менший, порівняно з порами, що їх спостерігали у лопатках до проведення операції ГІП. У результаті пластичної деформації, яку ініціює ГІП, утворюється «рафт»-структури у вигляді зональних ділянок, зосереджених у місцях «заліковування» пор, а також виділення скоагульованих частинок — фази, які спільно із пластинчастими(евтектичними) карбідами мають вигляд каркасу. Термообробка за стандартним режимом (1270 ℃, 1 год 15 хв) після газостатування сприяє перекристалізації зміцнюючої фази, підвищує структурну однорідність сплаву та спричинює релаксацію напружень, що виникли в процесі ГІП, а це позитивно впливає на фізико-механічні властивості. Чотиригодинна термічна обробка при температурі 1050 ℃, здійснена безпосередньо після операції ГІП, не усуває структурної неоднорідності, що характеризується наявністю лікваційних зон, а також областей, характерних для «рафт»- структури, що утворилися в процесі газостатування. Проведення після ГІП проміжного високотемпературного нагріву (гомогенізації) при температурі 1270 ℃ (1 год 15 хв) із подальшим нагріванням при температурі 1050 ℃ протягом 4 год сприяє отриманню більш однорідної структури сплаву ЖС32-ВІ (ВСК), що позитивно впливає на механічні та жароміцні властивості.

7 May 2026 in New Materials and Technologies in Metallurgy and Mechanical Engineering
Verified
Journal Article
Open access
SPSerhii Puchek
Serhii Puchek
SBSergiy Byelikov
Sergiy Byelikov
Purpose. To study the macro- and microstructural condition of VK-2500 gas turbine engine rotor blades in their original condition and after various processing stages. To evaluate their mechanical properties and long-term strength.Research methods. The material quality of first-stage gas turbine engine rotor blades made of Zhs26-VI heat-re-sistant nickel alloy was studied in their original condition and after hot isostatic pressing (HIP), as well as after HIP and standard heat treatment. Luminescence testing of the blades was performed using the LUM1-OV method. Microstructure examination was performed using optical microscopy (Neophot-32 microscope) and scanning electron microscopy (JSM T-300 microscope).Mechanical properties at room temperature were determined in accordance with ISO 6892-84 and ST SEV 471-88, and heat resistance parameters were determined in accordance with DSTU ISO 204:2019.Results. Metallographic studies revealed that the microstructure of the rotor blades is single-crystalline, with the main structural components being: γ′- solid solution with the presence of the intermetallic γ′- phase, the eutectic (γ-γ′) phase, carbides, and carbonitrides. A reduction in the size of the structural components is observed in the microstructure of the blades after HIP.Scientific novelty. New data on the structure and phase composition of the rotor blade material for aircraft gas turbine engines have been obtained. Heat treatment under standard conditions after HIP corresponds to almost complete recrystallization of the strengthening intermetallic γ′- phase, which consists of dissolution of the γ′- phase in the γ- matrix and its re-precipitation as dispersed particles of cubic morphology.Practical value. It has been shown that hot isostatic pressing in combination with standard heat treatment provides the most favorable combination of strength and ductility properties, as well as long-term durability of blades.

25 March 2025 in New Materials and Technologies in Metallurgy and Mechanical Engineering
Verified
Journal Article
Open access
PDF file
SBSergiy Byelikov
Sergiy Byelikov
ВКВіталій Кононов
Віталій Кононов
OHOlexandr Hlotka
Olexandr Hlotka
MSMichael Sydorenko
Michael Sydorenko
SPSergiy Pychek
Sergiy Pychek
СПСергій Пучек
Сергій Пучек
Purpose. To conduct comparative studies of the complex of physico-mechanical properties of the imported alloy N-155 and the domestic alloy ЗМІ-11 in order to increase the service life of the rotating blades. To conduct comparative tests on the short-term and long-term strength of the alloys in the initial state (after heat treatment), to conduct comparative tests on the short-term and long-term strength of the alloys after prolonged thermal action at T = 850 °C, 950 °C for 1000, 3000, 5000 hours and to conduct research by metallographic method and micro-X-ray spectral analysis of the microstructure and phase composition of the alloys. Research methods. Alloy samples were made from ingots weighing 10 kg in a vacuum induction furnace УППФ-3M in an argon environment at a pressure of 1.4–5.3 Pa in crucibles with the main lining with simultaneous pouring of samples of equiaxed crystallization. Chemical analysis was carried out by standard methods in accordance with the requirements of TU 14-1689-73 and OST 1.90127-85. Microstructure studies were carried out on microsections, the plane of which was oriented normal to the surface on a light optical microscope “Olympus IX-70” with a digital video camera “ExwaveHAD color video camera Digital Sony” at magnifications ×200, ×500, ×1000. Strength tests (GOST 1497-61, GOST 9651-61, GOST 1497-84) were carried out on standard cylindrical samples (diameter of the working part 5 mm, length 25 mm) at temperatures 200, 800, 900 and 1000°C on a УМЕ-10TM brand tensile machine. Long-term strength tests (GOST 10145-81) were carried out on standard cylindrical samples at temperatures 800, 900, 10000 °C and corresponding loads 600, 400, 180 MPa on an AIMA-5-2 machine. Obtained results. It was found that during tests at 800 and 900°С, the tensile strength of the N-155 alloy is 1.2 times lower than that of ЗМІ-11, and the long-term strength is 5.2 times lower, respectively. It was shown that the amount of the strengthening phase in the ЗМІ-11 alloy is 6…10 % more, evenly distributed throughout the alloy body. It was established that in the composition of the strengthening phase of the ЗМІ-11 alloy, the concentration of chromium, tungsten, and molybdenum remains practically unchanged and does not depend on the presence of niobium. At the same time, in the composition of the strengthening phase of the ЗМІ-11 alloy, the concentration of cobalt increases by 1.4 times, and the concentration of aluminum and titanium decreases by 1.1 times compared to the N-155 alloy. It was established that in the process of dissolving non-equilibrium eutectic precipitates, microvolumes arise, locally supersaturated with tungsten, chromium, and titanium, in which the probability of the formation of carbides on a more complex basis increases. It was found that during prolonged thermal action carbides based on tantalum TaC and on a mixed basis (Ta, Ti) C in the ЗМІ-11 alloy are thermally more stable than carbides in the N-155 alloy. Scientific novelty. The obtained results allow us to understand the thermodynamics of phase formation processes in two alloying systems and to establish the relationships between alloying elements concentration and the phase composition of the alloy. Practical value. The obtained results allow us to recommend the domestic ЗМІ-11 as a substitute for the foreign alloy N-155 without loss of properties and service life.