17 November 2023 in Science
Compared with the n-i-p structure, inverted (p-i-n) perovskite solar cells (PSCs) promise increased operating stability, but these photovoltaic cells often exhibit lower power conversion efficiencies (PCEs) because of nonradiative recombination losses, particularly at the perovskite/C 60 interface. We passivated surface defects and enabled reflection of minority carriers from the interface into the bulk using two types of functional molecules. We used sulfur-modified methylthio molecules to passivate surface defects and suppress recombination through strong coordination and hydrogen bonding, along with diammonium molecules to repel minority carriers and reduce contact-induced interface recombination achieved through field-effect passivation. This approach led to a fivefold longer carrier lifetime and one-third the photoluminescence quantum yield loss and enabled a certified quasi-steady-state PCE of 25.1% for inverted PSCs with stable operation at 65°C for >2000 hours in ambient air. We also fabricated monolithic all-perovskite tandem solar cells with 28.1% PCE.
7 August 2023 in Nature Electronics
1 April 2022 in Nature Communications
Despite the impressive development of metal halide perovskites in diverse optoelectronics, progress on high-performance transistors employing state-of-the-art perovskite channels has been limited due to ion migration and large organic spacer isolation. Herein, we report high-performance hysteresis-free p-channel perovskite thin-film transistors (TFTs) based on methylammonium tin iodide (MASnI3) and rationalise the effects of halide (I/Br/Cl) anion engineering on film quality improvement and tin/iodine vacancy suppression, realising high hole mobilities of 20 cm2 V−1 s−1, current on/off ratios exceeding 107, and threshold voltages of 0 V along with high operational stabilities and reproducibilities. We reveal ion migration has a negligible contribution to the hysteresis of Sn-based perovskite TFTs; instead, minority carrier trapping is the primary cause. Finally, we integrate the perovskite TFTs with commercialised n-channel indium gallium zinc oxide TFTs on a single chip to construct high-gain complementary inverters, facilitating the development of halide perovskite semiconductors for printable electronics and circuits.
21 August 2023 in Nature Electronics
Tin halide perovskites have the general chemical formula ASnX3, where A is a monovalent cation and X is a monovalent halide anion. These semiconducting materials can be used to fabricate p-type transistors at low cost and temperature and could be potentially integrated with n-type oxide-based transistors to create complementary circuits. However, the materials suffer from low crystallization controllability and high film defect density, resulting in uncompetitive device performance. Here we show that pure-tin perovskite thin-film transistors can be created using triple A cations of caesium–formamidinium–phenethylammonium. The approach leads to high-quality cascaded tin perovskite channel films with low-defect, phase-pure perovskite/dielectric interfaces. The optimized thin-film transistors exhibit hole mobilities of over 70 cm2 V−1 s−1 and on/off current ratios of over 108, which are comparable with commercial low-temperature polysilicon transistors. The transistors are fabricated using solution-processing methods at temperatures no higher than 100 °C. We also integrate the devices with n-type metal oxide transistors to create complementary inverters with voltage gains of 370, and NOR and NAND logic gates with rail-to-rail switching performance.
28 April 2025 in Nature Electronics
Solution-processed tin (Sn2+)-halide perovskites can be used to create p-channel thin-film transistors (TFTs) with performance levels comparable with commercial low-temperature polysilicon technology. However, high-quality perovskite film deposition using industry-compatible production techniques remains challenging. Here we report the fabrication of p-channel Sn2+-halide perovskite TFTs using a thermal evaporation approach with inorganic caesium tin iodide (CsSnI3). We use lead chloride (PbCl2) as a reaction initiator that triggers solid-state reactions of the as-evaporated perovskite compounds. This promotes the conversion of dense and uniform perovskite films, and also modulates the intrinsically high hole density of the CsSnI3 perovskite channels. Our optimized TFTs exhibit average hole field-effect mobilities of around 33.8 cm2 V−1 s−1, on/off current ratios of around 108, and large-area fabrication uniformity. The devices also exhibit improved stability compared with solution-deposited devices.