The cladding of titanium and graphite powders on the cp-titanium workpieces using the electron beam injected to the atmosphere provided the formation of the surface layers with a high content of high-strength carbide particles. The main structural components in cladded layers are α-Ti (αʹ-Ti), titanium carbide and graphite. Electron beam current is the main technological parameter defining a thickness of the hardened layer. An increasing beam current ranged from 20 to 23 mA leads to the cladded layer growth up to 2.9 mm. However, in this case a significant decrease of the microhardness level and the wear resistance level of the cladded layer is not observed. An average microhardess value of the hardened layer is of 430 HV. Under the conditions of friction against fixed abrasive particles, a wear resistance level of the cladded layers is by 32-45 % larger than that of cp-titanium.
Structural investigations of the materials obtained by surface alloying with titanium-containing powder compositions using industrial electron acceleration were carried out. It was revealed that hardened particles of titanium carbides and borides were formed as a result of high-energy treatment. The highest value of materials studied microhardness was about 8.4 GPa. Friction testing against fixed abrasive particles showed that electron-beam cladding of the titanium and graphite mixture conduced to increasing material wear resistance by a factor of three.
The influence of the cladding rate on the structure and microhardness parameter of coatings obtained by non-vacuum electron beam treatment of Ni-Cr-Si-B powder mixtures was investigated. Modified layers characterized by the gradient structure and consist of dendritic grains and a eutectic located at the grain boundaries. It was found that the lowest microhardness level (300 HV) was characteristic of the coatings obtained when the workpiece was moving relative to an electron beam with a speed of 10 mm per second. This treatment regime allowed obtaining high-quality coatings 2.5 mm in thickness. However, a large thickness of fusion penetration led to the interfusion of the base metal with a coating material and a decrease in the concentration of alloying elements in the coating. Reducing the lifetime of the liquid phase during treatment prevented intensive diffusion processes. Increasing the treatment velocity to 20 mm per second doubled the cladded layer microhardness (up to 650 HV).
The surface layer of steel was reinforced by electron-beam cladding at air atmosphere. Two types of powder mixtures were used to receive coatings: (1) titanium and graphite, (2) titanium and boron carbide. The formation of heterogeneous structure was observed in specimens after the electron-beam treatment by the methods of optical microscopy and scanning electron microscopy. The X-ray diffraction analysis was used to analyze the phase composition of the coatings. The wear resistance level of the coatings was estimated by friction test against loosely fixed abrasive particles. It was found that surface alloying of steel with carbon containing components led to the formation of material with an enhanced wear resistance level.
The electron beam cladding of vanadium and graphite powder mixture with additions of the flux agents on thick steel workpieces was implemented using the “ELV-6” electron accelerator. Structural and tribological investigations of the hardened surface were carried out. It was shown that cladding of vanadium-carbon powder mixtures by high-power electron beam injected to the atmosphere led to formation of high quality coatings. The highest microhardness level of cladded layer reached 12 GPa. Thickness of the surface layer was in the range 2.5-3.4 mm. Concentration of hard vanadium carbide particles increased with decrease of layer thickness which resulted in growing the wear resistance level of modified material.
1 December 2014 in Applied Mechanics and Materials
Structural investigations of steel surface layers alloyed with vanadium, titanium and graphite were carried out using optical microscopy, scanning electron microscopy (SEM) and X-ray diffraction analysis methods. Coatings were obtained by high-energy electron beam treatment. The titanium – vanadium ratio in initial powder mixtures was as 2:1, 1:1 and 1:2. TiC, a-Fe (ferrite), eutectic consisted of VC and a-Fe were the main structural components of the coating: With an increase of vanadium content shapeless TiC particles turned into dendritic; tertiary dendritic arms consisted of VC. In addition, it also resulted in an increase of carbide particle sizes. The volume fraction of strengthening particles in all coatings was approximately identical (18 %).