13 December 2014 in Journal of Macromolecular Science, Part B
Polylactide (PLA)/graphene oxide (GO) nanocomposites with different GO loadings were prepared by solution blending using tetrahydrofuran (THF) as solvent. The morphologies of the nanocomposites in the cast films and in subsequently isothermally crystallized samples were investigated separately. According to polarized optical microscopy images of the composites after isothermal crystallization, it was deduced that GO had nucleation effects on the crystallization of PLA and led to the size of spherulites decreasing and the number of spherulites increasing. However, by virtue of SEM, unique microsphere morphologies were found in the cast films of the PLA/GO composites. It was found that the features of this kind of microsphere were not influenced by the compositions but by the evaporation rate of the solvent during the preparation of the cast films. A faster evaporation rate of solvent resulted in smaller size of the microspheres. Based on DSC and FTIR results, it was proposed that the forming of this kind of microsphere was related to hydrogen bonds being formed between PLA and GO. The unique microsphere morphology is suggested to provide a new method to prepare PLA microsphere-based scaffolds.
30 January 2018 in Chinese Journal of Polymer Science
Fully biodegradable blends with low shape memory recovery temperature were obtained based on poly(lactic acid) (PLA) and poly(propylene carbonate) (PPC). By virtue of their similar chemical structures, in situ cross-linking reaction initiated by dicumyl peroxide (DCP) between PLA and PPC chains was realized in PLA/PPC blends. Therefore, the compatibility between PLA and PPC was increased, which obviously changed the phase structures and increased the elongation at break of the blends. The compatibilized blends had a recovery performance at 45 °C. Combining the changes of phase structures, the mechanism of the shape memory was discussed. It was demonstrated that in situ compatibilization by dicumyl peroxide was effective to obtain eco-friendly PLA/PPC blends with good mechanical and shape memory properties.
17 June 2019 in Journal of Applied Clinical Medical Physics
Polyvinyl chloride (PVC) is a commonly used tissue‐mimicking material (TMM) for phantom construction using 3D printing technology. PVC‐based TMMs consist of a mixture of PVC powder and dioctyl terephthalate as a softener. In order to allow the clinical use of a PVC‐based phantom use across CT and magnetic resonance imaging (MRI) imaging platforms, we evaluated the mechanical and physical imaging characteristics of ten PVC samples. The samples were made with different PVC‐softener ratios to optimize phantom bioequivalence with physiologic human tissue. Phantom imaging characteristics, including computed tomography (CT) number, MRI relaxation time, and mechanical properties (e.g., Poisson’s ratio and elastic modulus) were quantified. CT number varied over a range of approximately −10 to 110 HU. The relaxation times of the T1‐weighted and T2‐weighted images were 206.81 ± 17.50 and 20.22 ± 5.74 ms, respectively. Tensile testing was performed to evaluate mechanical properties on the three PVC samples that were closest to human tissue. The elastic moduli for these samples ranged 7.000–12.376 MPa, and Poisson’s ratios were 0.604–0.644. After physical and imaging characterization of the various PVC‐based phantoms, we successfully produced a bioequivalent phantom compatible with multimodal imaging platforms for machine calibration and image optimization/benchmarking. By combining PVC with 3D printing technologies, it is possible to construct imaging phantoms simulating human anatomies with tissue equivalency.
13 November 2015 in Chinese Journal of Polymer Science
The effects of graphene oxide (GO) with polar groups and functionalized GO (fGO) with nonpolar groups on the isothermal crystallization of poly(L-lactide) (PLLA) were compared. Functionalized GO was obtained by grafting octadecylamine and characterized by FTIR, WAXD and TGA. Isothermal crystallization kinetics of PLLA/GO and PLLA/fGO nanocomposites were investigated by combining DSC data and Avrami equation. The results showed that fGO could improve PLLA crystallization rate more obviously than GO. By analyzing the morphology obtained from POM, SEM and TEM, it was found fGO with large layer space dispersed better in PLLA and supplied more nucleation sites than GO. Therefore, for the multilayer graphene, increasing the layer spaces is important to improve its dispersion in polymers, which will cause the crystal kinetics changing of polymers.
29 February 2020 in Cellulose
21 November 2017 in Genes & Genomics