Resolvers as position sensors need a high frequency AC excitation voltage, and the induced voltage in their 2-phase perpendicular windings are amplitude modulated (AM) signals. For calculating the position, it is required to demodulated the output signals and calculate their envelopes. Then, inverse tangent can be used for calculating the position. Despite the advantages of resolvers, there are some drawbacks in their application. Calculating the envelopes is always one of the deep concerns in using resolvers. Furthermore, due to low-amplitude of the excitation flux, the performance of the resolvers is strongly affected by electromagnetic interference by the stray fields of motor and brake. Complicated winding process is the next challenge of resolvers. The last concern is referred to the high speed applications where to maintain the accuracy of the sensor it is required to increase the excitation frequency. While, the maximum frequency of excitation is limited by the frequency response of the employed ferromagnetic core and the employed resolver to digital converter (RDC). To overcome all the mentioned worries, a new permanent magnet (PM) resolver is proposed in this paper. The presented resolver has no copper winding and no need to the high frequency excitation. It is equipped by low-price Hall Effect sensors to measure the magnetic flux density and has a robust performance in high electromagnetic disturbance environments. All the analysis is done using time stepping finite element method (TSFEM) and verified by experimental measurements on a built prototype.
8 March 2018 in IEEE Transactions on Energy Conversion
Linear Variable Reluctance (LVR) resolvers have substantial benefits that make them suitable for linear motion control drives. The optimal design of LVR resolvers needs an accurate modelling that is usually achieved by three-dimensional (3-D) time stepping finite element method (TSFEM). However, 3-D TSFEM is very time consuming method and is unsuitable for co-usage with optimization algorithms. So, in this paper an accurate analytical model based on improved winding function (IWF) method is proposed. The proposed model is used to calculate the inductances, air-gap flux density, induced voltages and linear position error. The distinguished feature of the proposed model is direct usage of the turn function in calculating the inductances. While, the conventional modified winding function (MWF) method uses the Fourier Seri of the turn function. So, the proposed model is much faster and more accurate than the models based on conventional MWF method. The results of the proposed model are verified with those of 3-D TSFEM. Then, the proposed model is used for design optimization of the sensor. Also, two methods are proposed for compensating the longitudinal end effect. Finally, the experimental prototype is used to evaluate the developed analytical model and the optimization process.
31 May 2018 in IEEE Transactions on Industrial Electronics
Among position sensors, resolvers are superior from reliability point of view. However, obtaining lower output voltage harmonics and simple manufacturing process is a challenge in the design and optimization of resolvers. In this paper, a metaheuristic optimization algorithm is used to minimize total harmonic distortion of the output signals, and consequently the estimated position error in concentrated coil wound field resolvers. Meanwhile, to minimize total coil numbers, manufacturing costs, and complexity of the winding process, modified objective function and constraints are proposed. In this way, a modified winding function method is employed for performance analysis of the axial flux resolver. Then, the merits of the optimized winding configuration with respect to fractional slot concentrated windings are shown. The results of the proposed configurations are verified with a three-dimensional time-stepping finite-element method. Finally, the prototype of the studied axial flux resolver is constructed and tested. Good agreement is obtained between simulation and experimental results, confirming the effectiveness of the optimization process.
Multi-turn resolvers are supposed to be used in high accuracy industrial applications where both high resolution and absolute measurement is needed. The existed multi-turn resolvers are Wound-Rotor (WR) resolvers. While, Variable Reluctance (VR) resolvers are expected to be more cost efficient than WR resolvers. Because, they have a simple, solid rotor that make them independent of using rotary transformer. In this paper, a multi-turn VR resolver is proposed for such applications. Then, the proposed structure is optimized to decrease the ferromagnetic material’s volume and improve the performance of the sensor under mechanical faults. The studied mechanical faults include run out, static, dynamic, and mixed eccentricities that are studied independently and simultaneously. The analysis is done using Three-dimensional Time Stepping Finite Element Method (3-D TSFEM) and the optimal structure is experimentally built to validate the success of the design and optimizations.
Resolvers are electromagnetic position sensors that are widely used in industrial applications. In this paper, a novel axial flux resolver with a simple solid rotor is introduced for the first time. The stator of the proposed resolver has a disk type structure with two-phase distributed windings as signal windings and a concentric winding as an excitation winding. The rotor is a disc with a simple structure. Its width is 20° without any winding, and thus, the proposed resolver has the advantages of variable reluctance resolvers for having no winding on rotor and also its manufacturing process is much simpler than that of variable reluctance resolvers. The performance analysis of the proposed structure is simulated and optimized using a 3D time stepping finite element method. Then, a prototype is constructed based on the optimized dimensions and tested. Good agreement between the simulation and the experimental results validates the success of the proposed resolver.
16 November 2018 in IEEE Transactions on Energy Conversion
Nowadays, position sensors are increasingly used in many applications. One of the most commonly used sensors are resolvers. There are different types of resolvers including wound rotor resolvers, variable air-gap length variable reluctance resolvers, and sinusoidal rotor variable reluctance resolvers. Regardless of the resolvers' configurations, including linear, cylindrical and disk type, finite element analysis (FEA) is inseparable part of design and the performance evaluation of these magnetic sensors. The scope of this study is to discuss challenges in the FEA of resolvers. The influence of mesh quality, time steps, stop time, excitation methods including voltage source and current source and signal processing methods are investigated in detail. Then, a key question in analysis of resolvers is answered. The question is Is total harmonic distortion of induced voltages' envelopes a suitable criterion for the performance evaluation of resolvers? Finally, four prototypes of different types of resolvers are used for experimental tests. Good agreements are obtained between simulation and test results indicating the accuracy of following discussions.