InAlGaAs tunnel diodes, lattice-matched to InP and grown by molecular beam epitaxy, are demonstrated with peak tunneling current densities exceeding 1200 A/cm2. This was achieved by a 20 °C reduction in growth temperature for the p-type tunnel diode layers, resulting in up to two orders of magnitude improvement in the peak tunneling current density. Secondary ion mass spectrometry measurements reveal that the lower growth temperature reduces unwanted segregation of p-type Be dopants, improving dopant incorporation within the active tunnel diode layers. The diodes are transparent to wavelengths above 1000 nm and are compatible with the bottom junctions of InP-based multi-junction solar cells and with InP-based photonic power converters operating in the telecommunication O- and C-bands. When incorporated into a dual-junction photonic power converter test structure, measurements under 1319-nm laser illumination demonstrate integrated tunnel diode operation, enabling a halving of the short-circuit current and doubling of the open-circuit voltage as compared to a single junction reference device.
We present an approach to realize antimonide superlattices on silicon substrates without using conventional Indium-bump hybridization. In this approach, PIN superlattices are grown on top of a 60 nm Al0.6Ga0.4Sb sacrificial layer on a GaSb host substrate. Following the growth, the individual pixels are transferred using our epitaxial-lift off technique, which consists of a wet-etch to undercut the pixels followed by a dry-stamp process to transfer the pixels to a silicon substrate prepared with a gold layer. Structural and optical characterization of the transferred pixels was done using an optical microscope, scanning electron microscopy, and photoluminescence. The interface between the transferred pixels and the new substrate was abrupt, and no significant degradation in the optical quality was observed. An Indium-bump-free membrane detector was then fabricated using this approach. Spectral response measurements provided a 100% cut-off wavelength of 4.3 μm at 77 K. The performance of the membrane detector was compared to a control detector on the as-grown substrate. The membrane detector was limited by surface leakage current. The proposed approach could pave the way for wafer-level integration of photonic detectors on silicon substrates, which could dramatically reduce the cost of these detectors.
16 December 2016 in Proceedings of the National Academy of Sciences
Antimonide compounds are fabricated in membrane form to enable materials combinations that cannot be obtained by direct growth and to support strain fields that are not possible in the bulk. InAs/(InAs,Ga)Sb type II superlattices (T2SLs) with different in-plane geometries are transferred from a GaSb substrate to a variety of hosts, including Si, polydimethylsiloxane, and metal-coated substrates. Electron microscopy shows structural integrity of transferred membranes with thickness of 100 nm to 2.5 m and lateral sizes from m2 to cm2. Electron microscopy reveals the excellent quality of the membrane interface with the new host. The crystalline structure of the T2SL is not altered by the fabrication process, and a minimal elastic relaxation occurs during the release step, as demonstrated by X-ray diffraction and mechanical modeling. A method to locally strain-engineer antimonide-based membranes is theoretically illustrated. Continuum elasticity theory shows that up to 3.5% compressive strain can be induced in an InSb quantum well through external bending. Photoluminescence spectroscopy and characterization of an IR photodetector based on InAs/GaSb bonded to Si demonstrate the functionality of transferred membranes in the IR range. Significance In this work we present a versatile method to fabricate antimonide-based heterostructures in membrane form, and we demonstrate the potential of these materials to enable hybrid integration and elastic strain engineering. The relevance of our work is threefold. First, integration of Sb-based compound membranes with Si substrates will potentially solve a number of technological challenges in the fabrication of IR optoelectronic devices based on type II superlattices. Second, transfer of Sb compounds to insulating materials will enable a thorough investigation of electrical transport in the heterostructure via Hall and Van der Pauw measurements. Third, membrane technology applied to Sb-based structures will enable one to engineer strain distributions, which are not obtainable within the limitations of epitaxial growth processes.
We demonstrate thin-film GaSb solar cells which are isolated from a GaSb substrate and transferred to a Si substrate. We epitaxially grow ∼3.3 μm thick GaSb P on N diode structures on a GaSb substrate. Upon patterning in 2D arrays of pixels, the GaSb films are released via epitaxial lift-off and they are transferred to Si substrates. Encapsulation of each pixel preserves the structural integrity of the GaSb film during lift-off. Using this technique, we consistently transfer ∼4 × 4 mm2 array of pixelated GaSb membranes to a Si substrate with a ∼ 80%–100% yield. The area of individual pixels ranges from ∼90 × 90 μm2 to ∼340 × 340 μm2. Further processing to fabricate photovoltaic devices is performed after the transfer. GaSb solar cells with lateral sizes of ∼340 × 340 μm2 under illumination exhibit efficiencies of ∼3%, which compares favorably with extracted values for large-area (i.e., 5 × 5 mm2) homoepitaxial GaSb solar cells on GaSb substrates.
5 February 2021 in ACS Applied Materials & Interfaces